Standard Series, Single Socket Outlet, 125VAC, 10A, 2 PIN ParAllel, Surface Mount

Standard Series, Single Socket Outlet, 125VAC, 10A, 2 PIN ParAllel, Surface Mount WE

Item Number: 402-WE



Qty UoM EAN Colour



Product or component type


Product brand



Quantity per set

set of 1


without marking

Local signalling

without light indicator

Device mounting


Fixing mode

by screws

[in] rated current

10 A

[ue] rated operational voltage

110 V AC


28 mm

Fixing center

28 mm

Number of poles



AS/NZS 3100|AS/NZS 3112|AS/NZS 3133|AS/NZS 3000:approval number S/1

Reach regulation

Reference contains Substances of Very High Concern above the threshold

Eu rohs directive

Compliant with Exemptions

China rohs regulation

Product out of China RoHS scope. Substance declaration for your information


Package 1 bare product quantity


Cover type

complete housing


45 mm

Unit type of package 1


Number of units in package 1


Package 1 height

2.8 cm

Package 1 width

4.1 cm

Package 1 length

4.1 cm

Package 1 weight

32 g
Show all specifications

Frequently Asked Questions

hide show

On the Altivar drives, in CiA402 profile, what sequence is written to run drive in Reverse?

On the Altivar drives, in CiA402 profile, what sequence is written to run drive in Reverse?

Product LIne:
Altivar drives with serial communication control in CiA-402 (Drivecom) Mode of operation.

All current production models with the exception of the ATV212 series, all serial numbers

To issue a run command forward in CiA402 profile, you must write the sequence 6,7,15 to the command word.  What sequence should be written to run reverse?

In order to run, Bits 0-3 must be all high, this translates to decimal value of 15.  Bit 11 of the control word determines the direction of the the drive.  When bits 0,1,2,3 are high  (decimal 15) the drive runs in Forward direction.  When bits 0,1,2,3,11 are high (decimal 2063) the drive runs in Reverse direction.

What is the cut out size for Z4025, Zen series double outlet?

Please use the attached template for Z4025 cutout.User-added image
Please go to the following links below and check under the Documentation Tab for more information.

Australia -

New Zealand -

Video: Enabling Sell Mode on the Xantrex XW Hybrid Solar Inverter/Charger

1) Enable Grid support in XW basic setup menu
2) Set Grid Support Voltage to 64V (32V for XW4024) and enable SELL in XW Advanced - Grid Support menu (only if firmware on the XW inverter/charger is 1.07)
3) Verify XW CHARGE CYCLE is '2Stg/NoFloat' in XW Advanced - Charger Settings - Charge Cycle (factory default setting)
4) On MPPT set CHARGE CYCLE to '3 stage' in MPPT Advanced - Charger Settings - Charge Cycle 
5) It is also recommended that the system has a minimum battery capacity of 200Ah. An additional 100Ah for every 1kW of solar power is preferable.

What are the characteristics of the XW fan?

XW+/XW Series Fan Image

Note: There may be times where the fan needs to be replaced and customer would like to know the ratings of the fan. Physically, the fan's size is 12cm by 12cm.
Caution: This should only be done safely and by a qualified technician

How do I enable/disable SCP audible alarm when a fault occurs?

In order to enable/disable the audible alarm on the XW inverter/charger and the Conext SW Inverter/charger, you have to navigate through the system control panel.

From the System Status Screen
1.)  Press Enter
2.)  Under Select Device select the SCP
3.)  Scroll down until you see Fault Alarm
4.)  Press enter to enable/disable

*NOTE:  Below the fault alarm option there is an additional low battery alarm that you would need to enable separately from the fault alarm option