Standard Series Flush Plate Architrave Size, Switch Plate 1 Gang (75 x 32mm) | White Electric

How to trigger a action selector from C-Bus key switch

1. SELECT TRIGGER CONTROL FROM SECONDARY APPLICATION (UNIT IDENTIFICATION TAP)
2. SELECT THE SECONDARY APPLICATION FROM (P) TO (S) FROM THE SELECT KEY
3. SELECT THE TRIGGER CONTROL GROUP AND THEN FUNCTION AS TRIGGER 1 OR 2
4. SELECT THE THREE DASH TO SELECT THE ACTION SELECTOR

eg.5085DL

eg.5031nmml

 

The 31CAP and 31LCDA both have separate uses to resolve issues experienced with 2-wire Dimmers.

The 31CAP should be used when minimum load of the device is not being met, this is usually indicated by the load/light, that is controlled by the dimmer, by glowing when it should be off. Adding the 31CAP will increase the load and prevent the load/light from glowing in the off state. Depending on how far off minimum load you are more than one 31CAP may be required.

The 31LCDA should be used in instances where the load/light is flickering constantly, which indicates an issue with compatibility with the 2-wire dimmer used. The 31LCDA resolves these incompatibilities and flickering should then stop, if the flickering is reduced but still present you may need another 31LCDA to completely resolve. No more than 3x 31LCDA’s should be used on one dimmer.

If the load connected to the 41E300PBUD2SM is glowing when the dimmer is showing that it is switched off this usually indicates that the minimum load has not been met. 
You can then connect a 31CAP to increase the loading.

Issue:
Breakdown of components for 9001KYK117  

Product Line:
Harmony Push Buttons

Environment:
Harmony Control Stations

Cause:
Product Features

Resolution:
9001KYK117 components are:
1-9001KY1S1 (red enclosure)
1-9001K15 (break glass operator)
1-9001KA1 (1 open and 1 closed contact)
1-9001KN799RP (legend plate)

Replacement glass discs are 9001K57 (package of five)

MAXBAR with neutral terminal block can be used to distribute active and neutral in the row with main switch. Use the connectors provided with MAXBAR to take active and neutral feed from the row with main switch to take the feed to other rows. You can follow the same process for other rows in switchboard.

MAXBAR is a top feeding comb busbar able to feed Line & Neutral from the Main incoming Switch or MCB and neutral terminal directly to all type of Clipsal RCBOs and AFDDs. 

There are Comb busbar for 1P+N and 3P+N applications. There is one variant with neutral terminal block for rows with Main Switch  and another variant for rows without Main switch.

MAXBAR removes the need for cutting stripping, twisting and managing cables for feeding RCBO & AFDD on typical installation. This helps to achieve installation speed of up to 15x faster with MAXBAR compared to traditional wiring.

Iconic Outdoor is available in Matte White -XW and Matte Black -BK.

All Iconic Outdoor mounting points are outside the wiring area and do not need to be drilled or any additional sealant applied.

Iconic Outdoor suits both 20mm and 25mm conduit.

The 31CAP is a load correction device which consists of a "Capacitor only" to help 2 wire products achieve minimum load levels. The 31LCDA has circuitry built in to the device to enable it to correct minor compatibility issues found between dimmers and LED lights for example slight flickering when dimmed at a higher level.



31CAP - Increases minimum load.


For further information please visit http://www.clipsal.com/Trade/Products/ProductDetail?catno=31CAP



31LCDA - Assists with compatibility issues.



For further information please visit http://www.clipsal.com/Trade/Products/ProductDetail?catno=31LCDA

Issue:
Wants the Altivar VFD set to always run at a particular speed when no reference input is connected.

Product Line:
Altivar 12, 32, 312, 61, 71, 212, 320

Environment:
All models

Cause:
VFD does not run the motor without a speed reference.

Resolution:
If there is no external speed reference when the VFD gets a run command, then it will always run at the minimum speed programmed to the VFD.  Set the minimum speed parameter to the desired run speed.  Use parameter LSP for the Altivar12, 32, 312, 320, 61, 71 drives.  Use parameter LL for the Altivar 212 drive.  These can be adjusted while the motor is running.

Issue:
What is a possible cause of OSF fault? 

Product Line:
Altivar 312 , ATV312

Environment:
All

Cause:
Line voltage is too high
Problem with the line supply
Voltage spike on line side affecting DC bus voltage
Switching power factor correction capacitors by the facility or by the utility company

Resolution: 

• Check the line voltage at L1, L2, L3 on the drive terminals
• Compare the line voltage reading with the ULn display ( SUP menu)
• Measure the DC Bus voltage
• Monitor line power for voltage spikes