Standard Series Single Switch Socket Outlet 250V,10A, Skirt Mount | White Electric

Issue:
Connecting SoMove to the VFD using the Ethernet network connection.
 

Product Line:
ATV61 
ATV71 
ATV630
ATV930
ATV320
ATV340
ATV32

Environment:
Ethernet IP or Profinet option installed.
VW3A3316, VW3A3320, VW3A3627 VW3A3720

Cause:
Drive is not detected when attempting to connect.

Resolution:
See attachment for screenshots showing SoMove V2.9.4

STEP 1
Turn OFF your computers firewall before starting so you will have access to your Ethernet port. 


STEP 2
Edit Connection on your computers ethernet port and setup IP address in the Altivar Drive using an HMI.
Computer or PC setup:
Example setting up your PCs IP address.
Search Ethernet settings
-Change adapter options
- Choose the Ethernet port you want to use.
-Choose Properties
-Make sure IPV4 and IPV6 are both checked. 
-Double click on the IPV4 settings
-Select "Use the following IP address" and now enter in an IP address for your PCs ethernet port. 
Note this IP address needs to match your Drives IP address up to the last octet. 
Drives IP address= 10.172.86.1 (for the Drive) and your PC's IP address = 10.172.86.10 (your computer)
Subnet address= 255.255.255.0
-Choose ok


Drive Setup
Example set your Drives IP address using the remote HMI under the Ethernet settings in the programming. 
Type=Fixed
IP address= 10.172.86.1 (for the Drive) 
Subnet address= 255.255.255.0
-Power cycle your Drive after changing the IP address 


STEP 3 
Open up Somove 2.9.4 or newer and setup your "edit connection/scan" settings.
-Click on  "edit connection/scan"
-Choose Modbus TCP double click
-Choose the advanced settings (small gear wheel icon).
-Choose More
-Choose Scan tab
-Now type in your Drives IP address example 10.172.86.1  
-Choose Single Scan and enter 1 
-Apply and OK
-Ok again 


STEP 4 
-Now Scan for the Device to see if your PC finds the Drive. 
-double click on the picture of the drive to connect and load from the device.



NOTE: If your Drives ATV630 or ATV930 Firmware is version V3.3IE or above it will now include cyber security features and you will have to enter a password before connecting to the drive other Ethernet or Profinet. You can find this unique password on your HMI under the Communications menu, Embedded Ethernet configuration, and find SECE.  SECE select OK on the HMI and then select WDPE and press ok.  Your will now see your unique password example "iY^Nm9cV"
This password is temporary and will need to be changed and remembered.

The USERNAME: ADMIN (all caps)
The Password: iY^Nm9cV (for this example only) 







Please read and understand before checking OK. 



Somove is loading settings from the Drive to your Somove on your PC. 




Your are now connected to the Drive when the bar across the top turn's orange. 




Please be aware that you will be required to enter a password when you connect via Ethernet or Profinet if your Process Drive is version V3.3IE or higher so if you live in an area or work for a company that does not require or mandate having a password for Ethernet or Profinet for cyber security you can disable the feature if desired.  Otherwise leave the feature active which can offer the best cyber security. 




Done.  

NOTE:  

This example should work using. 
-Ethernet TCP
-Ethernet IP
-Profinet

 

1. The trip unit is energized by an external 24 Vdc applied to terminals F1-F2 (F1 negative-F2 positive).  See attachment for location of terminals.
2. The trip unit is energized by an FFTK or HHTK test kit
3. There is at least 100 V between two phases, AND the load reaches approximately 20% of the breaker's rated current.

• Note that the display will not power up with primary injection testing unless one of the conditions in bullet 1 above is met.
• Note that Ammeter trip units do not require external power and the display will come on with sufficient current flow alone.

Issue:
Which guard should be used with the 9001KR16 or 9001SKR16?

Product Line:
Push Buttons and Operator Interface

Environment:
9001K and 9001SK 30mm operators

Resolution:
The 9001K56YM or the 9001K56RM are suitable guards for this operator

Issue:
ATV16 VFD replacement.

Product Line:
ATV16 Altivar 16

Environment:
All models

Cause:
Seeking replacement VFD for the obsolete ATV16.

Resolution:
Recommend the ATV320 product line.

1. the load line-to-line voltage (V)
2. the maximum load phase current (I)

Single Phase Transformers: kVA = (V * I) /1000
Three Phase Transformers:  kVA = (V * I * 1.732) / 1000
where 1.732 is the simple numerical value for the square root of 3 (1.7320508...)
Then round up to the next standard 3ph kVA rating as found in Section 14 of SquareD/Schneider Electric Catalog, Digest 178 .

Single Phase Transformer Example: V = 240, I = 175; Therefore: kVA = (240 x 175) / 1000 = 42 kVA
This calculates to 42 kVA, thus we round up to a standard Single Phase size 50kVA.  From the Digest, an EE50S3H will satisfactorily serve this load.

Three Phase Transformer Example:  V = 208, I = 175; Therefore: kVA = (208 x 175 x 1.732) / 1000 = 63.05kVA
This calculates to 63+ kVA, thus we round up to a standard Three Phase size 75kVA.  From the Digest, an EXN75T3H will satisfactorily serve this load.

Note:  This is a sample kVA calculation and does not take into account possible special load requirements, such as found with motors or some medical equipment, or other specialty applications.


Amperage provided for a given KVA can be determined by similar techniques:

Single Phase Example:  Using a 50 KVA Single Phase Transformer as a starting point.  50KVA is equal to 50,000 VA. (K= 1,000)  The full value in VA, 50,000 is then divided by the Voltage 240V = 208 Amperes.  This is a "Two Step Division", technique:  VA / Voltage = Amperage. 

Three Phase Example:  Using a 75 KVA Three Phase Transformer as a starting point.  75 KVA is equal to 75,000 VA. (K= 1,000)  The full value in VA, 75,000 divided by 1.732 = 43,302, which is then divided by the Voltage 208V = 208.2 Amperes.  This is a "Three Step Division", technique:  VA / 1.732 / Voltage = Amperage. 


3.  As an alternative to these calculations, you may prefer to use the charts below.  Standard KVA sizes are shown on the left margin, Standard Line-to-Line Voltages are shown along the top margin. 

Chart Example:  Using the numbers from the earlier Three Phase Transformer Example V=208, I=175.  Use the chart titled "Three Phase Low Voltage Dry Type Transformers".  Following the 208V top margin entry, and reading down vertically, it is seen that the first entry in that 208V vertical column that will cover 175A, and then some, is 208A, which indicates a 75 KVA Transformer, shown in the next over vertical column to the left.

See pages 3 & 4 of document 7400HO9501 "Looking for Low Voltage Transformer Solutions" for more information and conversion tables.

Issue:
Needs the part numbers of the measuring board for the ATV61HC16N4 and ATV71HC13N4 drives

Product Line:
ATV61 and ATV71

Environment:
All

Cause:
Failed measuring board component within the drive.

Resolution:
The part number for the measuring board is VX5A71HC13N4 or VX5A71HC13N4F (For Fuji parts)
When a replacement Measurement board is needed, the serial  number of the VFD needs to be verified.
 
If the 8th digit of the Serial number is a "2" as shown below than the replacement part number must have an "F" suffix.
See Attachment
 

Issue:
Where can I download the EDS files for the Ethernet IP card?

Product Line:
ATV61, ATV71, ATV32, ATV Process

Environment:
All

Resolution:
Use this link to access the Global website where EDS files are available for download.  Be sure to download the EDS file that matches your Drive and Product Version.

https://www.schneider-electric.us/en/download/search/?docTypeGroup=3587139-Software%2FFirmware&docType=1555901-EDS+Files

You will need to find out your drive's product version to choose the correct EDS file.

Example:  In the ATV61 or ATV71; go to menu 1.11 in the drives menu enter
find the product Vxxxxxxxxx 

This product version will need to be the version of the EDS file you download for that specific drive.

Issue:
Break down of ETA  status word 3201 on the ATV61/ATV71 drives

Product Line:
Alitvar ATV61 and ATV71

Environment:
With Profibus option card

Cause:
Needs to know the bit breakdown for the ETA status word.

Resolution:
ETA status word for Word 3201
bit 0= Reserved
bit 1= Ready
bit 2= Running
bit 3= Fault
bit 4= Power section line supply present
bit 5= Reserved
bit 6= Reserved
bit 7= Alarm
bit 8= Reserved
bit 9= Command or Ref via network
bit 10= Referenced reached
bit 11= Reference outside of limit
bit 12= Reserved
bit 13= Reserved
bit 14= Stop via Keypad stop button
bit 15= Direction of motor  1=reverse 0=forward.

Issue:
ATV61HC16N4 and ATV71HC13N4 spare parts manual.

Product line: 
Altivar ATV61HC16N4 and ATV71HC13N4

Environment: 
ATV61HC16N4 and ATV71HC13N4 

Cause:
Someone needs a copy of the services manual for the ATV61HC16N4 and the ATV71HC13N4 drives.

Resolution:
Instruction bulletin 30072-452-78 is attached.
 

If you are after a replacement electronic switch for a 5012S164/4L-WE then order the standard item “B5034MNLPCB-WE” which contains a PCB Assy plus the Rear Cover.

If you are after an equivalent to a 5012S164/4L-WE the closest we have can be achieved by ordering 1 x “B12/30/6-WE” + 3 x “5031NMML” + 9 x “5031NMS”

If just for replacement then you could get B503xNL and remove the Metal Plate and just use the gang switch to replace the old unit.

DALI mapping

5080CTC Colour V2/3 touch screen controlling dalicontrol

If having socket error when enabling Dali Mapping

Go into window services and stop Dalibuilding scheduler

Over 7-10 years the battery requires replacing else if there is a power failure you’re risking losing time and all programming on the unit. 

The replacement battery is CR2477N 

Yes, the part number for end plugs is Clipsal 900/25/16P.



Please go to the website via the following links below and check under the Documentation Tab for more information.

Australia - https://www.clipsal.com/products/detail?CatNo=900/25/16P&itemno=900/25/16P-WE&tab-document-1=0
New Zealand - https://www.pdl.co.nz/products/detail?CatNo=900/25/16P&itemno=900/25/16P-WE&tab-document-1=0

Issue:
What is the product number for a complete through-the-door disconnect device for a GV2P

Product Line:
IEC Contactors and Starters

Environment:
GV2P Manual Starters and Protectors

Resolution:
There are three devices which include mechanism, shaft and handle:
GV2APN01 has a NEMA 1, 12 rating and is black
GV2APN02 has a NEMA 1, 12 rating and is red/yellow
GV2APN04 has a NEMA 3R, 4, 4X rating and is red/yellow