OptiLine 50 Trunking, Wall/Ceiling frame

OptiLine 50 WAll/Ceiling Frame, 80 x 63 mm, PC/ABS

Catalogue Number: INS12105
OptiLine 50 Trunking, Wall/Ceiling frame
Retail
N/A
RRP (Inc. GST)

Specifications

hide show
Range of product
OptiLine 50
Product or component type
wall/ceiling frame
Quantity per set
1 piece
Colour tint
white (RAL 9010)
Trunking dimension
80 x 63 mm
Trunking material
  • aluminium
  • plastic
    • Fixing mode
      screw-fixed
      Material
      PC/ABS
      Length
      88 mm
      Height
      130 mm
      Width
      225 mm
      Ambient air temperature for operation
      -25-60 °C
      IP degree of protection
      IP40
      IK degree of protection
      IK07
      Sustainable offer status
      Green Premium product
      REACh Regulation
      Free of Substances of Very High Concern above the threshold
      REACh free of SVHC
      Yes
      EU RoHS Directive
      Pro-active compliance (Product out of EU RoHS legal scope)
      Toxic heavy metal free
      Yes
      Mercury free
      Yes
      RoHS exemption information
      Yes
      China RoHS Regulation
       Pro-active China RoHS declaration (out of China RoHS legal scope)
      Environmental Disclosure
      ENVPEP090918EN
      Warranty
      18 months

      Frequently Asked Questions

      hide show

      What is the key lock replacement for a INS1250?

      You can replace the key lock with the following models

      33190 (https://www.schneider-electric.com/en/product/33190/ronis-keylock---for-masterpact-nt---off-position---2-same-key---el24135/)
      41950 (https://www.schneider-electric.com/en/product/41950/2-key-lock-%2B-1-flat-key).


       

      What is the part number for an end stop for the Optiline 50 ducting , INS12300?

      The part number for an end stop for the Optiline 50 ducting , INS12300 is - INS12304

      For further information , visit link below:-
      https://www.clipsal.com/Trade/search-results?q=INS12304
      User-added image

      Can part number INS51245 be installed in concrete?

      No part number INS51245 can not be installed in concrete.

      Does the INS62045 come with or without the actual power/data outlets?

      They come empty by default.

      What is the code extended front rotary handle / shaft for an INS250?

      Code = 31050

      What are the terminal spreaders that can be used for the INS320?

      LV432490 - 52.5mm Pitch
      Please follow the link for the data sheet:
      https://eshop.schneider-electric.com/product.aspx?org=21&lang=1&dist=276&prod_id=LV432490
       

      What is the part number for a floor box which is 310 x 310?

      The INS62044 has the dimensions of  311mm x 311mm x 105mm complete with a square plastic recessed lid. This part has provisions for 4 power and 4 data (suits 4 x 2000 or C2000 Series outlets). 
      The base is metal which is used primarily in a concrete floor.

      For further information please visit the following link: www.clipsal.com/Trade/Products/ProductDetail?catno=INS62044
       

      Is it possible to install the rectangular sensor at the incoming side of the Masterpact ACB with Micrologic 7.0?

      Yes, it is possible to install the rectangular sensor at the incoming side of the Masterpact Air circuit breaker (ACB).

      The earth leakage protection in Micrologic 7.0 trip unit will work correctly irrespective of whether the rectangular sensor is installed in the upstream or downstream.

      What happens when the dip switches on a EGX100 are set to "on" for termination?

      Issue:
      EGX100 termination dip switches are set to "on" for termination
       
      Product Line:
      EGX100

      Environment:
      EGX100

      Cause:
      When the termination is enabled (On), the EGX applies a 120 ohm resister across the RS485 terminals.

      In a 2 wire application the 120 ohm resistor is connected across the positive (+) and negative (-) terminals (In this 2-wire mode the RX+ and TX+ are jumpered together and the RX- and TX- are jumpered together).

      In the 4 wire application mode two 120 ohm resistors are connected. One is connected across the transmit plus (TX+) and transmit negative (TX-). The other is connected across the receive plus (RX+) and the receive negative (RX-).

      Resolution:
      The modbus standard specification requires both sides of a modbus daisy chain to be terminated.