Clipsal - General Accessories, Screws, 32mm x M3.5 x 0.8 Pitch, Plated

To be able to measure the energy out from a Solar Panel a meter needs to be able to do Four Quadrant Calculation.

This means it is capable of Identification of imported and exported active and reactive energy allows you to monitor energy flow in both directions: delivered from the utility and produced on-site.

In the iEM3000 series the following meters are capable of Four Quadrant Calculation.

iEM31** range - iEM3135, iEM3155, iEM3165, and iEM3175
iEM32** range - iEM3235, iEM3255, iEM3265, and iEM3275
iEM33** range - iEM3335, iEM3355, iEM3365, and iEM3375
iEM34** range - iEM3455, iEM3465, iEM3555, and iEM3565


 

There are two types of clock behaviours found on iEM3000 meter series.
iEM3110, iEM3210, iEM3150, iEM3250, iEM3310 and iEM3350
These meters lose the clock immediately after the power interruption as there is no super capacitor or battery built-in. When power is interrupted, the date and time are reset and you must enter configuration mode to configure the clock, if you require time information.

iEM3115, iEM3135, iEM3155, iEM3165, iEM3175, iEM3215, iEM3235, iEM3455/iEM3555, iEM3465/iEM3565, iEM3275, iEM3335, iEM3355, iEM3365, iEM3375, iEM3455, iEM3465, iEM3555 and iEM3565
These meters could  keep the clock running for up to 3 days in absence of external power, the meter design uses a built-in super capacitor (not a battery) to power the clock only and keep it running. If power is interrupted for longer than 3 days, the device automatically displays the screen to set Date and Time when power is restored.

Refer to User manual for further information (page 28).
https://www.se.com/ww/en/download/document/DOCA0005EN/

Issue

I cannot find the Modbus Register List for the METSEDM2355N Power Meter

 

Product Line

METSEDM2355N

 

Environment

Medium Meters

 

 

Resolution

Please find the attached Modbus Register List for the METSEDM2355N Power Meter

Issue:
Repair parts

Product Line:
Heavy Duty Safety Switch

Resolution:
The repair parts for the HU363SS, series F6 (F06) are as follows. No other parts are available.
Line Base Assembly - 4056775250 (arc suppressor not included)
-Line Base mounting screw - 4020515101 (3 required)
-Arc Suppressor Assembly - 4056635550
-Arc Suppressor mounting screw - 4020514501 (1 required)
-Lug assembly - 4025101851 (per lug)
-Lug Mounting Screw - 4020514202 (per lug)
-Mechanism Assembly - 4056646950 (NOTE: handle coupling, cover interlock defeat coupling, and lockplate gaskets may also need replacing)
-Handle Coupling - 4056699850
-Cover Interlock Defeat Coupling - 4056699750
-Handle Assembly - 4056894150 (also recommend replacing lockplate gaskets)
-Lockplate - 4056894201 (also recommend replacing lockplate gaskets)
-Lockplate Gasket - 4050322802 (2 required)
-Lockplate mounting screw - 2194900001 (2 required)
-Ground Lug - 4025101851 (2 required)
-Ground Lug Mounting Screw - 4020514801

The following applies to both Geo SCADA Expert / ClearSCADA

Area of Interest is not enabled by default. You can enable Area of Interest feature by ticking the check box in Alarms section of Server Configuration.

Right click on Server Icon > Server Configuration  > System Configuration > Alarms



Please note you will have to restart the Geo SCADA Expert server for the changes to take effect. 

Unfortunately there is No direct replacement for this part.

 
Customer will have to use our panel LED i.e CLITPLP3/4/5/6 and will have to source the DALI driver from a different manufacturer.

Discontinued DALI Driver specifications: https://eref.se.com/au/en/myse/product-pdf/CLITPLPDRVDALI