Quantcast

Twin Switch Socket Outlet, 250V, 10A, Standard Size

White Electric | Twin Switch Socket Outlet, 250V, 10A, Standard Size

Twin Switch Socket Outlet, 250V, 10A, Standard Size

Item Number: 25-WE

Datasheet

Barcode

Qty UoM EAN Colour
-
-
-

Specifications

Design

Surface finish

glossy

Sustainable offer status

Green Premium product

Range of product

Standard Series

Product brand

Clipsal

Physical

Control type

ON/OFF button

Number of gangs

2 gangs

Pin number

3

Number of power socket outlets

2

Actuator

  • switch
  • rocker

Fixing mode

by screws

Local signalling

without light indicator

Mounting position

horizontal

[Ue] rated operational voltage

250 V AC

[In] rated current

10 A

Depth

16 mm

Length

115 mm

Width

73 mm

Fixing center

84 mm

Standards

  • AS/NZS 3100
  • AS/NZS 3112
  • AS/NZS 3133
  • AS/NZS 3000:approval number S/1

REACh Regulation

Reference contains Substances of Very High Concern above the threshold

EU RoHS Directive

Compliant

Mercury free

Yes

RoHS exemption information

Yes

China RoHS Regulation

Product out of China RoHS scope. Substance declaration for your information

Environmental Disclosure

ENVPEP120506EN

Material

Material

PC (polycarbonate)

Others

Unit Type of Package 1

PCE

Number of Units in Package 1

1

Package 1 Weight

0.101 kg

Package 1 Height

3 cm

Package 1 width

7.3 cm

Package 1 Length

11.5 cm

Unit Type of Package 2

BB1

Number of Units in Package 2

10

Package 2 Weight

1.078 kg

Package 2 Height

12 cm

Package 2 width

13.8 cm

Package 2 Length

15.3 cm

Unit Type of Package 3

CAR

Number of Units in Package 3

100

Package 3 Weight

11.216 kg

Package 3 Height

25.4 cm

Package 3 width

34.8 cm

Package 3 Length

44.5 cm
Show all specifications

Documents & downloads

hide show
Filter items
  • All

  • Product Brochures

  • Technical Data Catalogues

  • Specifications

  • Declaration of Conformity

  • Certificates (MSDS)

Frequently Asked Questions

hide show

What is the command word for the ATS22 soft starters for network communication?

Issue:
Command word for the ATS22 soft starters.

Product Line:
Altistart ATS22

Environment:
All

Cause:
Modbus address for ATS22

Resolution:
The command word address for the ATS22 soft starter is 752.
The ETA status word address for the ATS22 soft starter is 256

See the attached PDF document for the Command word and the ETA status bit assignments.

Can circuit breakers be reverse-fed or back-fed?

Issue:
Ability of circuit breakers to be reverse fed

Product Line:
Circuit Breakers

Resolution:
Any circuit breaker that does NOT have Line and Load (or + and - on DC breakers) identifying markings may be reverse fed. See the compiled list below:

Breakers that can be back fed and exceptions (This is a work in process list, and does not include legacy breakers):
  • HOM (Excludes those with suffix GFI, EPD, AFI, CAFI and DF.)
  • QO and QOB (Excludes those with suffix GFI, EPD, EPE, AFI, CAFI and DF.)
  • QOU
  • Multi 9 products (Excludes the products rated 125VDC, and 250-500Vdc. Also excludes ID Residual current switches, GFP, DPN VIGI and Vigi modules.)
  • E frame for NF panel (Excludes those with suffix EPD.)
  • Powerpact H, J and L frame (Excludes those with T or R suffix, which are breakers with replaceable trip units. Also excludes those with Fxx suffix, which are "frame only" sold without terminations or trip unit.)
  • Powerpact Q frame and B frame
  • Powerpact M, P and R frame
  • Masterpact NT and NW (Excludes Masterpact DC rated breakers)
  • NOTE: Any Legacy or Powerpact breakers with GFM and ELM module attached cannot be reverse fed.

Video: How does the PK4MB2HA retaining kit install into the proper QO, single phase, 225 A max, convertible mains load centers?

Issue:
Product Design Features 
 
Product Line:
QO Load Centers
 
Resolution:
The PK4MB2HA retaining kit secures one QO 2-pole branch circuit breaker with or without electrical accessories to the Right side of the interior when used as a Back-Fed Main Breaker.
This retaining kit can ONLY be used for QO, 1phase, 150-225amp, Convertible main load centers, Series S01 and S02 and Plug-On Neutral Series S06 Load Centers.
The retaining bracket will mount over the face of the back-fed branch breaker and get secured using the single interior mounting screw that comes with the kit.
NOTE: QO-GFI and QO-AFI branch circuit breakers are NOT suitable for use as back-fed main circuit breakers.

The attached video is ONLY to supplement the INSTRUCTIONS that come with the kit. PLEASE make sure to read the instructions and all the below Safety Information that is located in the instructions BEFORE working on any electrical equipment.
A pdf copy of the complete instructions is attached below the video.
Danger label pic

Make sure to turn OFF ALL Power supplying the equipment and verify the power is OFF using a properly rated voltage sensing device, BEFORE working on or with electrical equipment. 
1) Once all Safety steps are followed, begin the kit installation by following the instructions.
2) Make sure to obtain the correct 2-pole, QO branch breaker to be used as the back-fed Main and DO NOT exceed the maximum rating marked on each load center.
3) As shown in step 2, on page 2 of the intructions, remove and discard the interior mounting screw(Fig. 1) 
4) Install the appropriate  QO back-fed branch breaker ONLY in positions 2-4 (The first two positions in the upper right side of the interior)
5) Center the retaining bracket over the breaker to be used as the back-fed breaker and press down against the face of the retaining bracket to seal it against the breaker.
6) Secure the retaining bracket to the base with the new interior mounting screw provided in the kit and torque to 35 lb-in (4 N-m)
7) Remove the backing of the wiring diagram label that comes in the kit, to expose the adhesive and attach the label to the inside of the load center enclosure or to the back of the cover.

NOTE: PLEASE READ ALL INSTRUCTIONS AND SAFETY INFORMATION THAT COME WITH THE KIT AND NEVER WORK ON ENERGIZED EQUIPMENT.

What are the repair parts for the HU363SS, series F6? (may be shown as F06)

Issue:
Repair parts

Product Line:
Heavy Duty Safety Switch

Resolution:
The repair parts for the HU363SS, series F6 (F06) are as follows. No other parts are available.
Line Base Assembly - 4056775250 (arc suppressor not included)
-Line Base mounting screw - 4020515101 (3 required)
-Arc Suppressor Assembly - 4056635550
-Arc Suppressor mounting screw - 4020514501 (1 required)
-Lug assembly - 4025101851 (per lug)
-Lug Mounting Screw - 4020514202 (per lug)
-Mechanism Assembly - 4056646950 (NOTE: handle coupling, cover interlock defeat coupling, and lockplate gaskets may also need replacing)
-Handle Coupling - 4056699850
-Cover Interlock Defeat Coupling - 4056699750
-Handle Assembly - 4056894150 (also recommend replacing lockplate gaskets)
-Lockplate - 4056894201 (also recommend replacing lockplate gaskets)
-Lockplate Gasket - 4050322802 (2 required)
-Lockplate mounting screw - 2194900001 (2 required)
-Ground Lug - 4025101851 (2 required)
-Ground Lug Mounting Screw - 4020514801

What is the operating principle of an XS1 ferrous/non-ferrous detector with materials?

Difference between ferrous and non-ferrous products

  • Ferrous products:  any steel
  • Non-ferrous products: any metal except steel (brass, copper, etc.)
Caution - non-ferrous does not mean any material (wood, plastic, etc.)


Difference between ferrous sensors and non-ferrous sensors

There are sensors which can detect:

Ferrous metals as a preference (steel, iron)
The sensing distances for these products vary according to the metals to be detected: maximum for ferrous and dependent on a Km coefficient typical of each metal (value between 0 and 1: Km = 1 for steel). This coefficient reduces the sensor detection range. For example if Km = 1 for cast iron, it is only 0.25 for copper. This is the conventional inductive sensor.
 

Both for ferrous (steel, iron) and non-ferrous (brass, aluminium, copper, etc) metals
The sensing distance for these sensors is the same for both ferrous and non-ferrous materials. The Km coefficient is always 1. They are called Ferrous/Non-Ferrous sensors. The Schneider part numbers are: XS1M18KPM40x, XS1M30KPM40x 18mm and 30mm diameter sensors respectively, and also XS7C40KPM40.
 

Difference in detection principles 
For both sensors, an LC oscillator creates an electromagnetic signal.

The difference in detection principles for the two types of sensor lies in:

  • Attenuation of the oscillation amplitude for ferrous materials, it is significant for ferrous materials and insignificant for non-ferrous materials
  • Variation in oscillation frequency for ferrous/non-ferrous materials. For high-frequency operation (in the region of one MHz), both types of material (ferrous and non-ferrous) have the same effect on the oscillation frequency variation.


Km coefficient depending on the different metalsKM coefficient

DALI rotary dimmer (DCDAL31SROT), if replacing the dimmer does it need to be reprogrammed?

If replacing just the slave rotary (DCCAL31SROT) then no but if replace the master unit (DCDAL31M2PB)  that the slave is connected to then yes.

The master switch can be use to control the light without the rotary slave only if the master is program with the same group/address.


Master/Rotary Save dali mech


connection between dali slave rotary and master mech
Show More