socket swt sing vert 10a 250v

Single Switch Socket Outlet, 250V, 10A, Standard Size, Vertical

Catalogue Number: 15V
socket swt sing vert 10a 250v
Colour: White Electric
Colour: Per UOM Std.
  • Cream 1 PCE
  • Red 1 PCE
  • White Electric 1 PCE
Added to cart

Specifications

hide show
Product brand
Clipsal
Range of product
Standard Series
Control type
ON/OFF button
Number of gangs
1 gang
Pin number
3
Number of power socket outlets
1
Actuator
  • rocker
  • switch
    • Mounting position
      vertical
      Fixing mode
      by screws
      Local signalling
      without light indicator
      Material
      PC (polycarbonate)
      Surface finish
      glossy
      [Ue] rated operational voltage
      250 V AC
      [In] rated current
      10 A
      Depth
      14 mm
      Length
      115 mm
      Width
      73 mm
      Fixing center
      84 mm
      Standards
    • AS/NZS 3100
    • AS/NZS 3112
    • AS/NZS 3133
    • AS/NZS 3000:approval number S/1
      • Sustainable offer status
        Green Premium product
        EU RoHS Directive
        Compliant
        Mercury free
        Yes
        RoHS exemption information
        Yes
        China RoHS Regulation
        Product out of China RoHS scope. Substance declaration for your information
        Environmental Disclosure
        ENVPEP120506EN

        Documents & downloads

        hide show
        Filter items
        • All

        • Product Brochures

        • Technical Data Catalogues

        Frequently Asked Questions

        hide show

        How does the shield connection of the comm port on ION8600/8650 connect to earth ground?

        The RS485 shield is connected to earth ground through a 120ohm resistor.
        The RS232 shield is connected to earth ground through a 15V sidactor, 1Mohm resistor, and a 1nF capacitor.


        Legacy KB System (APS) Data: RESL209509 V1.0, Originally authored by MaTh on 10/27/2012, Last Edited by MaTh on 10/27/2012
        Related ranges: ION8650, ION8600

        Communication Gateway - What pins are what on the RS485 (Modbus) Terminal Block? (eg. Rx+, Rx-, Tx+ and correct orientation)

        Pin 1 - 15V input
        Pin 2 - Ground
        Pin 3 - RS485 A
        Pin 4 - RS485 B
         
        RS485 is a bidirectional differential bus so there is no transmit and receive. Pin 1 is on the right when looking at the connector. See attached diagram.
         

        How to power a Xantrex System Control Panel when no XW+ or SW is present?

        When using a Xantrex System Control Panel, this unit is powered from either an XW+ or an SW hybrid inverter.

        When in a situation that either one of these hybrid inverters are not available, to get the SCP to operate, you will need to provide an independant 15V DC 200mA supply to the Xanbus network.

        +ve should be connected straight to pins 1,2 and 7. -ve should be connected to 3, 6 and 8.

        Do you have a 4 pole normally closed 159 Series contactor?

        Unfortunately the 4 pole normally closed 159 Series contactor was a part of the Square D brand and has been discontinued.

        What is the minimum ring Voltage the ION8650 modem can detect?

        Issue
        What is the minimum ring Voltage the ION8650 modem can detect?

        Product Line
        ION8650
        ION8600

        Environment
        Modem communications

        Resolution
        The vendor specification for RING detection use the frequency range from 15Hz to 68Hz and a DC offset of 35V and above with up to 100V RMS RING. This range covers 99.99% of all real world ring scenarios and there are no approval agencies that we are aware of that are outside of that range. Normal ring offset is usually 37V to 48V DC with a ring voltage less than 100V RMS.

        We have tested 15V RMS and have been able to detect RING, but the test equipment was generating a perfect 20 Hz sine wave for TIP and RING and they are opposite of each other. Not every provided TIP/RING signal will be perfect (or even a sine wave) so that would change the actual RING detect voltage. Firmware version 1.02u was tested at 14 Hz and tested to 20 V and 68 Hz tested to 19 V.

        What is the 154 that suits the Slimline range?

        The 154 to suit the Slimline range is the 154RM.

        What is the standard key used in a 9001KX,9001KR, 9001KS and 9001SKS selector switch?

        Issue:
        Replacement standard key for the 9001 oeprators.

        Product Line:
        Harmony Pushbuttons

        Environment:
        All Products

        Resolution:
        The standard key is the E10 key which is catalog number 2941101100.
         

        Is the extra switch in the 15X removable?

        Yes, the extra switch in the 15X is removable. Any 230v rated 30 series mec will fit in it's place.

         

        Do you have a 15S in biege?

        No, the 15S only comes in White Electric and Red.

        Some of the key features are:
        • 1 pole
        • Standard size
        • Safety shutter
        For further information please visit https://www.clipsal.com/Trade/Products/ProductDetail?catno=15Shttps://www.clipsal.com/Trade/Products/ProductDetail?catno=15S

        What is the part code for a caravan lead with RCD 15m permanent connection

         The part code is PDL 953/15

        Is there a PDL 953/15 that is longer than 15m

         No not available 
        Please note this product is being phased out

        What are the dimensions of the 535 power tower

         Dimensions 158 x 158 x 140mm high
        Show More