Altivar 312, Variable speed drive ATV312, 0.37kW, 1kVA, 41 W, 200..240 V, 1 phase supply
Item Number: ATV312H037M2
Specifications
Design
Range of product
Product or component type
Product destination
Warranty
Physical
Supply
- internal supply for logic inputs: 19...30 V 100 mA, protection type: overload and short-circuit protection
- internal supply for reference potentiometer (2.2 to 10 kOhm): 10...10.8 V 10 mA, protection type: overload and short-circuit protection
Communication port protocol
- Modbus
- CANopen
Ip degree of protection
- IP20 on upper part without cover plate
- IP21 on connection terminals
- IP31 on upper part
- IP41 on upper part
Protection type
- input phase breaks: drive
- line supply overvoltage and undervoltage safety circuits: drive
- line supply phase loss safety function, for three phases supply: drive
- motor phase breaks: drive
- overcurrent between output phases and earth (on power up only): drive
- overheating protection: drive
- short-circuit between motor phases: drive
- thermal protection: motor
Insulation resistance
Local signalling
- 1 LED (red) for drive voltage
- four 7-segment display units for CANopen bus status
Connector type
Marking
Height
Width
Depth
Net weight
Standards
- IEC 61800-5-1
- IEC 61800-3
Product certifications
- UL
- C-Tick
- NOM
- CSA
- DNV
- GOST
Relative humidity
- 5...95 % without condensation conforming to IEC 60068...2-3
- 5...95 % without dripping water conforming to IEC 60068...2-3
Ambient air temperature for storage
Ambient air temperature for operation
- -10...50 °C without derating (with protective cover on top of the drive)
- -10...60 °C with derating factor (without protective cover on top of the drive)
Eu rohs directive
Rohs exemption information
China rohs regulation
Environmental disclosure
Circularity profile
California proposition 65
Others
Package 1 bare product quantity
Product specific application
Assembly style
Component name
Motor power kw
Motor power hp
[us] rated supply voltage
Supply frequency
Network number of phases
Line current
- 5.3 A at 200 V, Isc = 1 kA
- 4.4 A at 240 V
Emc filter
Apparent power
Maximum transient current
Power dissipation in w
Speed range
Asynchronous motor control profile
- factory set : constant torque
- sensorless flux vector control with PWM type motor control signal
Electrical connection
- Al1, Al2, Al3, AOV, AOC, R1A, R1B, R1C, R2A, R2B, LI1...LI6 terminal 2.5-2.5 mm² AWG 14
- L1, L2, L3, U, V, W, PA, PB, PA/+, PC/- terminal 2.5-2.5 mm² AWG 14
Option card
- communication card for CANopen daisy chain
- communication card for DeviceNet
- communication card for Fipio
- communication card for Modbus TCP
- communication card for Profibus DP
Supply voltage limits
Prospective line isc
Continuous output current
Output frequency
Nominal switching frequency
Switching frequency
Transient overtorque
Braking torque
- 150 % during 60 s with braking resistor
- 100 % with braking resistor continuously
- 150 % without braking resistor
Regulation loop
Motor slip compensation
- automatic whatever the load
- suppressable
- adjustable
Output voltage
Tightening torque
- Al1, Al2, Al3, AOV, AOC, R1A, R1B, R1C, R2A, R2B, LI1...LI6: 0.6...0.6 N.m
- L1, L2, L3, U, V, W, PA, PB, PA/+, PC/-: 0.8...0.8 N.m
Insulation
Analogue input number
Analogue input type
- AI1 configurable voltage 0...10 V, input voltage 30 V max, impedance: 30000 Ohm
- AI2 configurable voltage +/- 10 V, input voltage 30 V max, impedance: 30000 Ohm
- AI3 configurable current 0...20 mA, impedance: 250 Ohm
Sampling duration
- AI1, AI2, AI3: 8 ms analog
- LI1...LI6: 4 ms discrete
Response time
- AOV, AOC 8 ms for analog
- R1A, R1B, R1C, R2A, R2B 8 ms for discrete
Linearity error
Analogue output number
Analogue output type
- AOC configurable current: 0...20 mA, impedance: 800 Ohm, resolution: 8 bits
- AOV configurable voltage: 0...10 V, impedance: 470 Ohm, resolution: 8 bits
Discrete input logic
- logic input not wired (LI1...LI4), < 13 V (state 1)
- negative logic (source) (LI1...LI6), > 19 V (state 0)
- positive logic (source) (LI1...LI6), < 5 V (state 0), > 11 V (state 1)
Discrete output number
Discrete output type
- configurable relay logic: (R1A, R1B, R1C) 1 NO + 1 NC - 100000 cycles
- configurable relay logic: (R2A, R2B) NC - 100000 cycles
Minimum switching current
Maximum switching current
- R1-R2: 2 A at 250 V AC inductive load, cos phi = 0.4 and L/R = 7 ms
- R1-R2: 2 A at 30 V DC inductive load, cos phi = 0.4 and L/R = 7 ms
- R1-R2: 5 A at 250 V AC resistive load, cos phi = 1 and L/R = 0 ms
- R1-R2: 5 A at 30 V DC resistive load, cos phi = 1 and L/R = 0 ms
Discrete input number
Discrete input type
Acceleration and deceleration ramps
- S, U or customized
- linear adjustable separately from 0.1 to 999.9 s
Braking to standstill
Time constant
Frequency resolution
- analog input: 0.1...100 Hz
- display unit: 0.1 Hz
Physical interface
Transmission frame
Transmission rate
- 10, 20, 50, 125, 250, 500 kbps or 1 Mbps for CANopen
- 4800, 9600 or 19200 bps for Modbus
Number of addresses
- 1...127 for CANopen
- 1...247 for Modbus
Number of drive
- 127 for CANopen
- 31 for Modbus
Operating position
Network frequency
Dielectric strength
- 2040 V DC between earth and power terminals
- 2880 V AC between control and power terminals
Electromagnetic compatibility
- 1.2/50 µs - 8/20 µs surge immunity test level 3 conforming to IEC 61000-4-5
- electrical fast transient/burst immunity test level 4 conforming to IEC 61000-4-4
- electrostatic discharge immunity test level 3 conforming to IEC 61000-4-2
- radiated radio-frequency electromagnetic field immunity test level 3 conforming to IEC 61000-4-3
Pollution degree
Protective treatment
Vibration resistance
- 1 gn (f= 13-150 Hz) conforming to EN/IEC 60068-2-6
- 1.5 mm (f= 3-13 Hz) conforming to EN/IEC 60068-2-6
Shock resistance
Operating altitude
- <= 1000 m without derating
- 1000...2000 m with current derating 1 % per 100 m
Unit type of package 1
Number of units in package 1
Package 1 height
Package 1 width
Package 1 length
Package 1 weight
Unit type of package 2
Number of units in package 2
Package 2 height
Package 2 width
Package 2 length
Package 2 weight
Weee
Product contributes to saved and avoided emissions
Documents & downloads
hide show-
All
-
CAD Files and Packs
-
Technical Data Catalogues
-
Installation Instruction
-
End of Life Manual
-
Operating Manuals
-
System User Guide
-
Certificates (MSDS)
-
Declaration of Conformity
-
Software - Data Library
Frequently Asked Questions
hide showPart number for ATV312 Din rail mounting kit
Product Line:
ATV312
Environment:
All
Cause:
Desire to utilize din mounting kit option
Resolution:
The part numbers need to order the mounting kit for this drive are VW3A9804 and VW3A9805.
VW3A9804 covers the following range of drives: ATV312....
018M2, H037M2, H055M2, H075M2, H018M3, H037M3, H055M3, H075M3
VW3A9805 covers the following range of drives: ATV312....
HU11M2, HU15M2, HU11M3, HU15M3, HU22M3, H037N4, H055N4, H075N4, HU11N4, HU15N4, H075S6, HU15S6
Note: The din rail mounting kits are only available for the above drives.
Note: Other drives not list above do not have a din rail kit.
Powering the ATV312 by an external 24Vdc only
Product Line:
Altivar 312
Environment:
All
Cause:
Installation/programming
Resolution:
No, this drive must have line voltage applied. The voltage must be within -15% to +10% of the rated line voltage.