Quantcast

Clipsal MAX4 Mini Active link 100 A 500 V 6 hole with cover front wiring Red

Clipsal MAX4 Mini Active link 100 A 500 V 6 hole with cover front wiring Red

Clipsal MAX4 Mini Active link 100 A 500 V 6 hole with cover front wiring Red

Item Number: L6R

Retail
$51.37
RRP (Inc. GST)

Datasheet

Barcode

Qty UoM EAN Colour
-
-
-

Specifications

Design

Product brand

Clipsal

Range of product

Blue Point

Product or component type

active link

Physical

[In] rated current

100 A

[Ue] rated operational voltage

500 V

Connector type

screw terminals

REACh Regulation

Free of Substances of Very High Concern above the threshold

EU RoHS Directive

Compliant

Mercury free

Yes

RoHS exemption information

Yes

China RoHS Regulation

Product out of China RoHS scope. Substance declaration for your information

Others

Number of Units in Package 1

1

Package 1 Height

55 mm

Package 1 Length

46 mm

Package 1 width

70 mm

Unit Type of Package 1

PCE

Cable cross section

16-16 mm²

Package 1 Weight

72 g
Show all specifications

Frequently Asked Questions

hide show

Why do you not see the LFr parameter to control in keypad mode and has Altivar ATV16 with keypad VW3A16102?

Issue:
Can't find LFr parameter to control in keypad mode and has Altivar ATV16 with keypad VW3A16102.
 
Product Line:
ATV16
 
Environment:
All
 
Cause:
No LFR parameter
 
Resolution: 
The LFr parameter does not appear if the keypad part number VW3A16102 (which is required) datecode is before 9422.
 

What is the maximum DC voltage per pole for TeSys F Range contactors.

The maximum DC voltage for TeSys F range contactors is 125 Volt per pole. This voltage is applicable for the specification of L/R <= 15ms in DC applications.

What is the maximum DC voltage per pole for TeSys D range contactors.

The maximum DC voltage for TeSys D range contactor is 75 Volt per pole. This voltage is applicable for the specification of L/R <= 15ms in DC applications.

What is the scaling unit for ATV600 motor current (LCR) parameter?

When reading the value of LCR parameter using Modbus the scaling unit varies as follows:  
  • 0,01 for all sizes below or equal to 15KW 
  • 0,1A between 18,5 to 160KW 
  • 1A over 160KW 

 

How do you set up the Altivar 28 drive so the start / stop / speed are controlled by the remote keypad?

Issue:
Altivar 28 start/stop/speed controlled via remote keypad.

Product Line:
Altivar 28

Environment:
All

Cause:
N/A

Resolution:
Go to the I/O ( input / output ) menu and set LCC ( local control) to Yes which no allows acces to LFR ( local frequency) parameter for local speed adjustment.  
To change the reference setting you will need to go to the SET menu and change parameter LFR each time desire to change the speed the drive is commanded to run at..

What can cause an ULF motor underload fault on the ATS48 soft starter?

Issue:
ATS48 tripping on ULF or motor underload fault.

Product Line:
Altistart ATS48

Environment:
All

Cause:
The soft starter is programmed for activation motor underload (ULL) in the Pr0 menu.
The motor underload threshold parameter (LUL) is set to 60% and the drive is running only 58% or lower motor torque viewed in the SUP menu parameter (Ltr).

Resolution:
Troubleshooting:
Check Motor underload threshold parameter (LUL) in menu PrO and compare it the motor torque parameter in the SUP menu.   If your LUL parameter is set lower then the Ltr in the SUP then the soft starter will trip on ULF fault.
Show More