Blue Point Fused Terminal Blocks, 250V, 10A, Fuse

Blue Point Fused Terminal Blocks, 250V, 10A, Fuse

Blue Point Fused Terminal Blocks, 250V, 10A, Fuse

Item Number: BPF10

RRP (Inc. GST)



Qty UoM EAN Colour



Product brand




25 mm

[Ue] rated operational voltage

250 V AC

[In] rated current

10 A

EU RoHS Directive

Under investigation



6 mm

Unit Type of Package 1


Number of Units in Package 1


Package 1 Weight

2 g

Package 1 Height

6 mm

Package 1 width

6 mm

Package 1 Length

25 mm
Show all specifications

Frequently Asked Questions

hide show

What is BP3160 conditional rating of 63kA certificate/ conformity?

Please see attached the BP3160 cover page report which specifies the rating.

Video: Back-UPS CS, RS & XS - Manual Adjustment for Sensitivity


UPS will not operate on utility power or may be clicking between utility and battery power.

Product Line:

Back-UPS RS/XS & Back-UPS CS (4-LED Interfaces)


All models & serial numbers


This may be caused by one of the following conditions;
  • Low Voltage / Sag
  • Black-out
  • High Voltage / Over-Voltage
  • Frequency is out of range
  • Total Harmonic Distortion


The following video details the process for manually adjusting the Back-UPS RS & XS or Back-UPS CS system's AC Input Sensitivity.

What is the amperage rating for the PDL DBF10

The amperage is 100A

What is 56 Series equivalent to part number PDL MP410?

The part number for 56 series equivalent is a 56P410.

What faults can be reset with the ATV61 or ATV71 automatic restart function turned on?

What faults can be reset with the automatic restart on ATV61/71?

Product Line:
Variable Frequency Drives

Applies to Altivar 61/71

Customer wants to know if he can automatically restart the drive after a fault 


Faults that can be reset with automatic restart function, after the cause has disappeared:
APF, CnF, COF, EPF1, EPF2, FCF2, Fd1, LFF2, LFF3, LFF4, nFF, ObF, OHF, OLC, OLF, OPF1, OPF2, OSF, OtF1, OtF2, OtFL, PHF, PtF1, PtF2, PtFL, SLF1, SLF2, SLF3, SPIF, SSF, tJF and ULF

NOTE: In order for the Automatic Restart function to clear a fault and attempt a restart, ALL of the following must be true:
  • The cause of the original fault must be resolved
  • The drive must be set up for 2 wire control
  • 2-wire type set to level
  • Drive controlled by the drive's terminals
  • The run command must be maintained

These faults that can be cleared by Automatic Restart are listed in the ATV61 and ATV71 Programming Manuals.

ATV61 Programming Manual:

ATV71 Programming Manual:

ATV61/71 the Logic Input will not reset the External Fault?

The ATV71 has External Fault assigned to LI5.  When active, LI5 trips the drive into External Fault, EPF1.  When activating Fault Reset on LI4, the fault is not reset.  

Product line:
Altivar 61 ATV61 Altivar 71 ATV71


The fault reset needs to come from the assigned Command Channel.

In this case, Command Channel 1 was assigned to a Communications network. A Fault Reset needs to come from the Communications Network.
Fault reset by Logic Input is not possible unless the active command channel is Terminals.  

Consider temporarily switching the Command Channel to Terminals and then close Logic Input assigned to Reset, or switch to HMI mode and use the local Stop/Reset button (push twice) to reset.  

Alternatively see the recommendations from L3 attached.
Show More