The part code is 2000-WE surround cover plate
Unfortunately, we only make a 2 gang version.
Yes the part number is 2031VH-RD
No. Unfortunately, part number 30M35 CANNOT be used in 2031V66.
The 2031RC series consists of 2031RC30, 2031VRC30, 2031RC10, 2031VRC10, ML2031RC10 and ML2031VRC10.
The twin brown wires power the Line Power Available LED. These wires must be connected into the Line Active and Neutral terminals with the incoming supply wires.
For further information please refer to the attached installation instruction
No, unfortunately you will need to buy the parts separately.
Yes, The grid plate has a terminal block on the back and is rated at 30A. The part number is 2031VXCB.
No, We do not supply or encourage this as the 2031v66 has a specific gasket set up to ensure weatherproof rating and this may be compromised if tampered with therefore we only sell them assembled.
Unfortunately we dont do the mech as a spare part it is essentually a 30 mech with a rubber seal between the contacts ant the dolly and we dont do that mech as a spare part.
The part number for cover to suit P2031VA is - P2001
Yes, one off 2031VH + one off 5031NMML
Part no P2031VH will fit on either 449A or 449ASD mounting block
No Medilec permanent connection unit
Use 2031VH with a 38TB Mech.
The following parts are required to build the equivelent: 1x C2031VH + 1x 5031NMML
Yes, as it is based on 30 series mech with 4 terminals it is 2 way compatible.
Some of the key features are:
- 1 gang weatherproof switch
- Standard size gridplate and surround complete with one 30M switch
- Vertical mount
- 116 mm Length x 76 mm Width x 30 mm Depth
- 84 mm apart Mounting centres
For further information please visit https://www.clipsal.com/Trade/Products/ProductDetail?catno=2031V66
No, the mech is intergrated into the grid, and cannot be purchased seperately.
The IP66 rated weather proof indoor switches avaliable are 2031V66, C2031V66.
The part number is P2031VA.
No unfortunately we only go up to 2 gang (C2032V66)
This is not done by clipsal but an outside contractor please contact PLACARD in NSW on 02 9588 8200 Contact Helen Perente
Part numbers are P2031VH (single) P2032VH (double) P30M (Mech)
The cord is a 800CL-WE and the sockets are either 2031VCS-WE or 31VCS-WE.
The coil codes available for the U-Line Motor Starter control units are as follows:
24VDC is BL
24VAC is B
48-72V DC or 48V AC is ES
110-240V AC/DC is FU.
We do not have 480VAC coils available
CTA-ID : 2031577
Yes, one off 2034VH + one off 5031NMML + three off 5031NMS
Yes, one off C2032VH + one off 5031NMML + one off 5031NMS
Yes, one off C2034VH + one off 5031NMML + three off 5031NMS
Yes, one off SC2032VH + one off 5031NMML + one off 5031NMS
Will the LA4DC1U work on the CAd32BD relay
IEC relays and accessories
Products sold and used in the United States
Identifying product compatibility
The CAD32BD with DC coil has built-in coil suppression protection as standard so the LA4DC1U is not needed.
CTA-ID : 2031917
No. Unfortunately, Mechs only are not available for switch.
The codes are 5031NMML and 5031NMS respectively.
Any clipsal plate that fits 30 series mechs
Electrical Distribution Equipment
It takes 4.5`` of mounting height.
4031VH* Grid & plates to suit 30 series page 17 -
mech code 30USBCM
* - denotes colour of grid plate
No, unfortunately this mechanism does'nt fit the Saturn series. However, this mechanism will fit into the coms Saturn series comunication plate 4031VH.
The 2031VETR3 will not operate without a neutral however the 2031VETR WILL operate without a neutral as it was designed purely as a 2 wire device I.e. Active & Switched Active.
Unfortunately this part is unavailable. As an alternative you could use the WS226I, however it is a different range and looks entirely different.
Some of the key features are:
- 1 gang
- M100 rating
- Weather protected switch
- Outdoor lighting, Illuminated signs applications
For further information please visit https://www.clipsal.com/Trade/Products/ProductDetail?catno=WS226I
GV Manual Motor Starters and Protectors
The GV2MC01 has an IP41 rating ( similar to Nema Type 1 ), whereas the GV2MC02 has an IP55 rating (similar to the Nema Type 12 ).
Yes, however you will require these three components:
|P2000 Prestige Series plate
|P2000 Prestige pannel mounting clip
|Cat 6a UTP Connector Mechanism To fit 30 Mech