surround pvc w/proof box

Weatherprotected Boxes and Enclosures, Box SurRound for Finished SurRound

Catalogue Number: 255Z
surround pvc w/proof box
Colour: Grey
Colour: Per UOM Std.
  • Grey 1 PCE
Added to cart

Specifications

hide show
Product brand
Clipsal
Material
PVC (polyvinyl chloride)
Depth
6 mm
Length
149 mm
Width
111 mm
EU RoHS Directive
Compliant
Toxic heavy metal free
Yes
Mercury free
Yes
RoHS exemption information
Yes
China RoHS Regulation
 Pro-active China RoHS declaration (out of China RoHS legal scope)

Frequently Asked Questions

hide show

Do you sell the flap only for the 255?

Yes, we do sell the flap only for the 255. The part number is 255FLAP.

Some of the key features are:
  • For weatherprotected enclosure
For further information please visit https://www.clipsal.com/Trade/Products/ProductDetail?catno=255FLAP

What is the part number for flap to suit 255?

The part number for flap to suit 255 is 255FLAP-TR.

What is the IP rating of the 255?

The IP rating of the 255 is IP53.

For more information, please refer to the link:
https://www.clipsal.com/Trade/Products/ProductDetail?catno=255

What is part number for lid to suit 255?

Part number is actually 255FLAP -TR

What is the part number for a replacement flap for the 255?

The part number for a replacement flap for the 255 is - 255FLAP

For further information , visit link below:-
https://www.clipsal.com/Trade/search-results?q=255FLAP

What is the Pot Level of the C-Bus 5753L if the Potentiometer A set to fully clockwise?

It reads 2550 lux, if the Pot A at the fully clockwise position.

Is is possible to scale ATV320 analog input to have precisely 25.0Hz when AI1=5V

Issue:
Need to scale to have 5V equal 25Hz speed. 

Product line:
Altivar 320, ATV320 Altivar Machine

Environment:
all models

Cause:
n/a

Resolution:
By default, the analog input on the ATV320 follows Low speed to High speed in Inputs/Outputs CFG > Reference Template = Standard

To have the drive follow 25Hz with 5V analog signal, set LSP to 0.0 and HSP to 50Hz. Otherwise 5V cannot refer to 25Hz.
If necessary adjust AI1 min value, AI1 max value, AI1 range, AI1 Interim points X or Y. 

See the extracted pages from the ATV320 programming manual attached

What are the basic troubleshooting steps for the Smart-UPS SMX1500RM2U ?


Issue:

What are the basic troubleshooting steps for the Smart-UPS SMX1500RM2U ?

Product Line:

Smart-UPS

Environment:

SMX1500RM2U - All Serial Numbers

Cause:

During normal operation, you may find your UPS not functioning as expected. This may be due to a malfunction, configuration issue, or the install environment.
This document will assist you with basic troubleshooting steps.

Resolution:

 
Problem Possible Cause Solution
     
The UPS will not turn on or there is no output The unit has not been turned on. Press the ON button once to turn on the UPS. Please note that the LCD screen may be lit even though the UPS is OFF.
  The UPS is not connected to utility power. Be sure that the power cable is securely connected to the unit and to the utility power supply.
  The input circuit breaker has tripped. Reduce the load to the UPS, disconnect nonessential equipment and reset the circuit breaker. 
  The unit shows very low or no input utility voltage Check the utility power supply to the UPS by plugging in a table lamp. If the light is very dim, check the utility voltage.
  The battery connector plug is not securely connected. Be sure that all battery connections are secure.
  There is an internal UPS fault. Do not attempt to use the UPS. Unplug the UPS and have it serviced immediately
     
The UPS is operating on battery, while connected to utility power The input circuit breaker has tripped. Reduce the load to the UPS, disconnect nonessential equipment and reset the circuit breaker.
  There is very high, very low, or distorted input line voltage. Move the UPS to a different outlet on a different circuit. Test the input voltage with the utility voltage display. If acceptable to the connected equipment, reduce the UPS sensitivity.
     
UPS is beeping The UPS is in normal operation. None. The UPS is protecting the connected equipment.
     
UPS does not provide expected backup time The UPS battery is weak due to a recent outage or is near the end of its service life. Charge the battery. Batteries require recharging after extended outages and wear out faster when put into service often or when operated at elevated temperatures. If the battery is near the end of its service life, consider replacing the battery even if the replace battery indicator is not yet illuminated.
  The UPS is overloaded.  Check the UPS load display. Unplug unnecessary equipment, such as printers
     
Display interface LEDs flash sequentially The UPS has been shut down remotely through software or an optional accessory card. None. The UPS will restart automatically when utility power is restored.
     
Fault LED illuminates Possible Internal Fault Contact APC Support for further assistance. Take care to note the exact fault message on the LCD Display
     
All LEDs are illuminated and the UPS is plugged into a wall outlet The UPS has shut down and the battery has discharged from an extended outage. None. The UPS will return to normal operation when the power is restored and the battery has a sufficient charge.
     
The Replace Battery LED is illuminated The battery has a weak charge Allow the battery to recharge for at least four hours. Then, perform a self-test. If the problem persists after recharging, replace the battery
  The replacement battery is not properly connected. Be sure that the battery connector is securely connected.
     
The UPS displays a site wiring fault message Wiring faults detected include missing ground, hot-neutral, polarity reversal, and overloaded neutral circuit. If the UPS indicates a site wiring fault, have a qualified electrician inspect the building wiring. (Applicable for 120 V units only.)

What are the basic troubleshooting steps for the Smart-UPS SMX2000LV / SMX3000LV ?


Issue:

What are the basic troubleshooting steps for the Smart-UPS SMX2000LV / SMX3000LV ?

Product Line:

Smart-UPS

Environment:

SMX2000LV / SMX3000LV - All Serial Numbers

Cause:

During normal operation, you may find your UPS not functioning as expected. This may be due to a malfunction, configuration issue, or the install environment.
This document will assist you with basic troubleshooting steps.

Resolution:

 
Problem Possible Cause Solution
     
The UPS will not turn on or there is no output The unit has not been turned on. Press the ON button once to turn on the UPS. Please note that the LCD screen may be lit even though the UPS is OFF.
  The UPS is not connected to utility power. Be sure that the power cable is securely connected to the unit and to the utility power supply.
  The input circuit breaker has tripped. Reduce the load to the UPS, disconnect nonessential equipment and reset the circuit breaker. 
  The unit shows very low or no input utility voltage Check the utility power supply to the UPS by plugging in a table lamp. If the light is very dim, check the utility voltage.
  The battery connector plug is not securely connected. Be sure that all battery connections are secure.
  There is an internal UPS fault. Do not attempt to use the UPS. Unplug the UPS and have it serviced immediately
     
The UPS is operating on battery, while connected to utility power The input circuit breaker has tripped. Reduce the load to the UPS, disconnect nonessential equipment and reset the circuit breaker.
  There is very high, very low, or distorted input line voltage. Move the UPS to a different outlet on a different circuit. Test the input voltage with the utility voltage display. If acceptable to the connected equipment, reduce the UPS sensitivity.
     
UPS is beeping The UPS is in normal operation. None. The UPS is protecting the connected equipment.
     
UPS does not provide expected backup time The UPS battery is weak due to a recent outage or is near the end of its service life. Charge the battery. Batteries require recharging after extended outages and wear out faster when put into service often or when operated at elevated temperatures. If the battery is near the end of its service life, consider replacing the battery even if the replace battery indicator is not yet illuminated.
  The UPS is overloaded.  Check the UPS load display. Unplug unnecessary equipment, such as printers
     
Display interface LEDs flash sequentially The UPS has been shut down remotely through software or an optional accessory card. None. The UPS will restart automatically when utility power is restored.
     
Fault LED illuminates Possible Internal Fault Contact APC Support for further assistance. Take care to note the exact fault message on the LCD Display
     
All LEDs are illuminated and the UPS is plugged into a wall outlet The UPS has shut down and the battery has discharged from an extended outage. None. The UPS will return to normal operation when the power is restored and the battery has a sufficient charge.
     
The Replace Battery LED is illuminated The battery has a weak charge Allow the battery to recharge for at least four hours. Then, perform a self-test. If the problem persists after recharging, replace the battery
  The replacement battery is not properly connected. Be sure that the battery connector is securely connected.
     
The UPS displays a site wiring fault message Wiring faults detected include missing ground, hot-neutral, polarity reversal, and overloaded neutral circuit. If the UPS indicates a site wiring fault, have a qualified electrician inspect the building wiring. (Applicable for 120 V units only.)

What are the basic troubleshooting steps for the Smart-UPS SMX2000RMLV2U / SMX2200RMLV2U / SMX3000RMLV2U ?


Issue:

What are the basic troubleshooting steps for the Smart-UPS SMX2000RMLV2U / SMX2200RMLV2U / SMX3000RMLV2U ?

Product Line:

Smart-UPS

Environment:

SMX2000RMLV2U / SMX2200RMLV2U / SMX3000RMLV2U - All Serial Numbers

Cause:

During normal operation, you may find your UPS not functioning as expected. This may be due to a malfunction, configuration issue, or the install environment.
This document will assist you with basic troubleshooting steps.

Resolution:

 
Problem Possible Cause Solution
     
The UPS will not turn on or there is no output The unit has not been turned on. Press the ON button once to turn on the UPS. Please note that the LCD screen may be lit even though the UPS is OFF.
  The UPS is not connected to utility power. Be sure that the power cable is securely connected to the unit and to the utility power supply.
  The input circuit breaker has tripped. Reduce the load to the UPS, disconnect nonessential equipment and reset the circuit breaker. 
  The unit shows very low or no input utility voltage Check the utility power supply to the UPS by plugging in a table lamp. If the light is very dim, check the utility voltage.
  The battery connector plug is not securely connected. Be sure that all battery connections are secure.
  There is an internal UPS fault. Do not attempt to use the UPS. Unplug the UPS and have it serviced immediately
     
The UPS is operating on battery, while connected to utility power The input circuit breaker has tripped. Reduce the load to the UPS, disconnect nonessential equipment and reset the circuit breaker.
  There is very high, very low, or distorted input line voltage. Move the UPS to a different outlet on a different circuit. Test the input voltage with the utility voltage display. If acceptable to the connected equipment, reduce the UPS sensitivity.
     
UPS is beeping The UPS is in normal operation. None. The UPS is protecting the connected equipment.
     
UPS does not provide expected backup time The UPS battery is weak due to a recent outage or is near the end of its service life. Charge the battery. Batteries require recharging after extended outages and wear out faster when put into service often or when operated at elevated temperatures. If the battery is near the end of its service life, consider replacing the battery even if the replace battery indicator is not yet illuminated.
  The UPS is overloaded.  Check the UPS load display. Unplug unnecessary equipment, such as printers
     
Display interface LEDs flash sequentially The UPS has been shut down remotely through software or an optional accessory card. None. The UPS will restart automatically when utility power is restored.
     
Fault LED illuminates Possible Internal Fault Contact APC Support for further assistance. Take care to note the exact fault message on the LCD Display
     
All LEDs are illuminated and the UPS is plugged into a wall outlet The UPS has shut down and the battery has discharged from an extended outage. None. The UPS will return to normal operation when the power is restored and the battery has a sufficient charge.
     
The Replace Battery LED is illuminated The battery has a weak charge Allow the battery to recharge for at least four hours. Then, perform a self-test. If the problem persists after recharging, replace the battery
  The replacement battery is not properly connected. Be sure that the battery connector is securely connected.
     
The UPS displays a site wiring fault message Wiring faults detected include missing ground, hot-neutral, polarity reversal, and overloaded neutral circuit. If the UPS indicates a site wiring fault, have a qualified electrician inspect the building wiring. (Applicable for 120 V units only.)

What are the basic troubleshooting steps for the Smart-UPS SMX2000RMHV2U / SMX3000RMHV2U ?


Issue:

What are the basic troubleshooting steps for the Smart-UPS SMX2000RMHV2U / SMX3000RMHV2U ?

Product Line:

Smart-UPS

Environment:

SMX2000RMHV2U / SMX3000RMHV2U - All Serial Numbers

Cause:

During normal operation, you may find your UPS not functioning as expected. This may be due to a malfunction, configuration issue, or the install environment.
This document will assist you with basic troubleshooting steps.

Resolution:

 
Problem Possible Cause Solution
     
The UPS will not turn on or there is no output The unit has not been turned on. Press the ON button once to turn on the UPS. Please note that the LCD screen may be lit even though the UPS is OFF.
  The UPS is not connected to utility power. Be sure that the power cable is securely connected to the unit and to the utility power supply.
  The input circuit breaker has tripped. Reduce the load to the UPS, disconnect nonessential equipment and reset the circuit breaker. 
  The unit shows very low or no input utility voltage Check the utility power supply to the UPS by plugging in a table lamp. If the light is very dim, check the utility voltage.
  The battery connector plug is not securely connected. Be sure that all battery connections are secure.
  There is an internal UPS fault. Do not attempt to use the UPS. Unplug the UPS and have it serviced immediately
     
The UPS is operating on battery, while connected to utility power The input circuit breaker has tripped. Reduce the load to the UPS, disconnect nonessential equipment and reset the circuit breaker.
  There is very high, very low, or distorted input line voltage. Move the UPS to a different outlet on a different circuit. Test the input voltage with the utility voltage display. If acceptable to the connected equipment, reduce the UPS sensitivity.
     
UPS is beeping The UPS is in normal operation. None. The UPS is protecting the connected equipment.
     
UPS does not provide expected backup time The UPS battery is weak due to a recent outage or is near the end of its service life. Charge the battery. Batteries require recharging after extended outages and wear out faster when put into service often or when operated at elevated temperatures. If the battery is near the end of its service life, consider replacing the battery even if the replace battery indicator is not yet illuminated.
  The UPS is overloaded.  Check the UPS load display. Unplug unnecessary equipment, such as printers
     
Display interface LEDs flash sequentially The UPS has been shut down remotely through software or an optional accessory card. None. The UPS will restart automatically when utility power is restored.
     
Fault LED illuminates Possible Internal Fault Contact APC Support for further assistance. Take care to note the exact fault message on the LCD Display
     
All LEDs are illuminated and the UPS is plugged into a wall outlet The UPS has shut down and the battery has discharged from an extended outage. None. The UPS will return to normal operation when the power is restored and the battery has a sufficient charge.
     
The Replace Battery LED is illuminated The battery has a weak charge Allow the battery to recharge for at least four hours. Then, perform a self-test. If the problem persists after recharging, replace the battery
  The replacement battery is not properly connected. Be sure that the battery connector is securely connected.
     
The UPS displays a site wiring fault message Wiring faults detected include missing ground, hot-neutral, polarity reversal, and overloaded neutral circuit. If the UPS indicates a site wiring fault, have a qualified electrician inspect the building wiring. (Applicable for 120 V units only.)

What are the basic troubleshooting steps for the Smart-UPS SMX2000HV / SMX3000HV ?


Issue:

What are the basic troubleshooting steps for the Smart-UPS SMX2000HV / SMX3000HV ?

Product Line:

Smart-UPS

Environment:

SMX2000HV / SMX3000HV - All Serial Numbers

Cause:

During normal operation, you may find your UPS not functioning as expected. This may be due to a malfunction, configuration issue, or the install environment.
This document will assist you with basic troubleshooting steps.

Resolution:

 
Problem Possible Cause Solution
     
The UPS will not turn on or there is no output The unit has not been turned on. Press the ON button once to turn on the UPS. Please note that the LCD screen may be lit even though the UPS is OFF.
  The UPS is not connected to utility power. Be sure that the power cable is securely connected to the unit and to the utility power supply.
  The input circuit breaker has tripped. Reduce the load to the UPS, disconnect nonessential equipment and reset the circuit breaker. 
  The unit shows very low or no input utility voltage Check the utility power supply to the UPS by plugging in a table lamp. If the light is very dim, check the utility voltage.
  The battery connector plug is not securely connected. Be sure that all battery connections are secure.
  There is an internal UPS fault. Do not attempt to use the UPS. Unplug the UPS and have it serviced immediately
     
The UPS is operating on battery, while connected to utility power The input circuit breaker has tripped. Reduce the load to the UPS, disconnect nonessential equipment and reset the circuit breaker.
  There is very high, very low, or distorted input line voltage. Move the UPS to a different outlet on a different circuit. Test the input voltage with the utility voltage display. If acceptable to the connected equipment, reduce the UPS sensitivity.
     
UPS is beeping The UPS is in normal operation. None. The UPS is protecting the connected equipment.
     
UPS does not provide expected backup time The UPS battery is weak due to a recent outage or is near the end of its service life. Charge the battery. Batteries require recharging after extended outages and wear out faster when put into service often or when operated at elevated temperatures. If the battery is near the end of its service life, consider replacing the battery even if the replace battery indicator is not yet illuminated.
  The UPS is overloaded.  Check the UPS load display. Unplug unnecessary equipment, such as printers
     
Display interface LEDs flash sequentially The UPS has been shut down remotely through software or an optional accessory card. None. The UPS will restart automatically when utility power is restored.
     
Fault LED illuminates Possible Internal Fault Contact APC Support for further assistance. Take care to note the exact fault message on the LCD Display
     
All LEDs are illuminated and the UPS is plugged into a wall outlet The UPS has shut down and the battery has discharged from an extended outage. None. The UPS will return to normal operation when the power is restored and the battery has a sufficient charge.
     
The Replace Battery LED is illuminated The battery has a weak charge Allow the battery to recharge for at least four hours. Then, perform a self-test. If the problem persists after recharging, replace the battery
  The replacement battery is not properly connected. Be sure that the battery connector is securely connected.
     
The UPS displays a site wiring fault message Wiring faults detected include missing ground, hot-neutral, polarity reversal, and overloaded neutral circuit. If the UPS indicates a site wiring fault, have a qualified electrician inspect the building wiring. (Applicable for 120 V units only.)

What are the basic troubleshooting steps for the Smart-UPS SMC1000 / SMC1500 ?


Issue:

What are the basic troubleshooting steps for the Smart-UPS SMC1000 / SMC1500 ?

Product Line:

Smart-UPS

Environment:

SMC1000 / SMC1500 - All Serial Numbers

Cause:

During normal operation, you may find your UPS not functioning as expected. This may be due to a malfunction, configuration issue, or the install environment.
This document will assist you with basic troubleshooting steps.

Resolution:

 
Problem Possible Cause Solution
     
The UPS will not turn on or there is no output The unit has not been turned on. Press the ON button once to turn on the UPS. Please note that the LCD screen may be lit even though the UPS is OFF.
  The UPS is not connected to utility power. Be sure that the power cable is securely connected to the unit and to the utility power supply.
  The input circuit breaker has tripped. Reduce the load to the UPS, disconnect nonessential equipment and reset the circuit breaker. 
  The unit shows very low or no input utility voltage Check the utility power supply to the UPS by plugging in a table lamp. If the light is very dim, check the utility voltage.
  The battery connector plug is not securely connected. Be sure that all battery connections are secure.
  There is an internal UPS fault. Do not attempt to use the UPS. Unplug the UPS and have it serviced immediately
     
The UPS is operating on battery, while connected to utility power The input circuit breaker has tripped. Reduce the load to the UPS, disconnect nonessential equipment and reset the circuit breaker.
  There is very high, very low, or distorted input line voltage. Move the UPS to a different outlet on a different circuit. Test the input voltage with the utility voltage display. If acceptable to the connected equipment, reduce the UPS sensitivity.
     
UPS is beeping The UPS is in normal operation. None. The UPS is protecting the connected equipment.
     
UPS does not provide expected backup time The UPS battery is weak due to a recent outage or is near the end of its service life. Charge the battery. Batteries require recharging after extended outages and wear out faster when put into service often or when operated at elevated temperatures. If the battery is near the end of its service life, consider replacing the battery even if the replace battery indicator is not yet illuminated.
  The UPS is overloaded.  Check the UPS load display. Unplug unnecessary equipment, such as printers
     
Display interface LEDs flash sequentially The UPS has been shut down remotely through software or an optional accessory card. None. The UPS will restart automatically when utility power is restored.
     
Fault LED illuminates Possible Internal Fault Contact APC Support for further assistance. Take care to note the exact fault message on the LCD Display
     
All LEDs are illuminated and the UPS is plugged into a wall outlet The UPS has shut down and the battery has discharged from an extended outage. None. The UPS will return to normal operation when the power is restored and the battery has a sufficient charge.
     
The Replace Battery LED is illuminated The battery has a weak charge Allow the battery to recharge for at least four hours. Then, perform a self-test. If the problem persists after recharging, replace the battery
  The replacement battery is not properly connected. Be sure that the battery connector is securely connected.
     
The UPS displays a site wiring fault message Wiring faults detected include missing ground, hot-neutral, polarity reversal, and overloaded neutral circuit. If the UPS indicates a site wiring fault, have a qualified electrician inspect the building wiring. (Applicable for 120 V units only.)

What are the basic troubleshooting steps for the Smart-UPS SMC1000-2U / SMC1500-2U ?


Issue:

What are the basic troubleshooting steps for the Smart-UPS SMC1000-2U / SMC1500-2U ?

Product Line:

Smart-UPS

Environment:

SMC1000-2U / SMC1500-2U - All Serial Numbers

Cause:

During normal operation, you may find your UPS not functioning as expected. This may be due to a malfunction, configuration issue, or the install environment.
This document will assist you with basic troubleshooting steps.

Resolution:

 
Problem Possible Cause Solution
     
The UPS will not turn on or there is no output The unit has not been turned on. Press the ON button once to turn on the UPS. Please note that the LCD screen may be lit even though the UPS is OFF.
  The UPS is not connected to utility power. Be sure that the power cable is securely connected to the unit and to the utility power supply.
  The input circuit breaker has tripped. Reduce the load to the UPS, disconnect nonessential equipment and reset the circuit breaker. 
  The unit shows very low or no input utility voltage Check the utility power supply to the UPS by plugging in a table lamp. If the light is very dim, check the utility voltage.
  The battery connector plug is not securely connected. Be sure that all battery connections are secure.
  There is an internal UPS fault. Do not attempt to use the UPS. Unplug the UPS and have it serviced immediately
     
The UPS is operating on battery, while connected to utility power The input circuit breaker has tripped. Reduce the load to the UPS, disconnect nonessential equipment and reset the circuit breaker.
  There is very high, very low, or distorted input line voltage. Move the UPS to a different outlet on a different circuit. Test the input voltage with the utility voltage display. If acceptable to the connected equipment, reduce the UPS sensitivity.
     
UPS is beeping The UPS is in normal operation. None. The UPS is protecting the connected equipment.
     
UPS does not provide expected backup time The UPS battery is weak due to a recent outage or is near the end of its service life. Charge the battery. Batteries require recharging after extended outages and wear out faster when put into service often or when operated at elevated temperatures. If the battery is near the end of its service life, consider replacing the battery even if the replace battery indicator is not yet illuminated.
  The UPS is overloaded.  Check the UPS load display. Unplug unnecessary equipment, such as printers
     
Display interface LEDs flash sequentially The UPS has been shut down remotely through software or an optional accessory card. None. The UPS will restart automatically when utility power is restored.
     
Fault LED illuminates Possible Internal Fault Contact APC Support for further assistance. Take care to note the exact fault message on the LCD Display
     
All LEDs are illuminated and the UPS is plugged into a wall outlet The UPS has shut down and the battery has discharged from an extended outage. None. The UPS will return to normal operation when the power is restored and the battery has a sufficient charge.
     
The Replace Battery LED is illuminated The battery has a weak charge Allow the battery to recharge for at least four hours. Then, perform a self-test. If the problem persists after recharging, replace the battery
  The replacement battery is not properly connected. Be sure that the battery connector is securely connected.
     
The UPS displays a site wiring fault message Wiring faults detected include missing ground, hot-neutral, polarity reversal, and overloaded neutral circuit. If the UPS indicates a site wiring fault, have a qualified electrician inspect the building wiring. (Applicable for 120 V units only.)

What is the part number for the flap of 255 as a spare?

The part number for the flap of 255 as a spare is 255FLAP-TR.

What is the operating voltage for the Vamp 255 digital inputs?

Issue: Need to know the operating voltage of the Vamp 255 digital inputs.

Product Line: Vamp 255

Resolution: The Vamp 255 has 2 sets of digital inputs. Digital inputs 1-6 are internally wetted with 48Vdc. The other 12 digital inputs operating voltage is defined by the part number ordering code:
A = 40 - 265 VAC/VDC
B = 18 - 36 VDC
C = 40 - 265 VAC/VDC + ARC Protection
D =  18 - 36 VDC + ARC Protection
E = 40 - 265 VAC/VDC + D19, DI20 + ARC channel
F = 18 - 36 VDC + D19, DI20 + ARC channel

Keywords: Vamp 255, Vamp 255 digital inputs, Vamp 255 operating voltage

What is the maximum number of variable that can be shared between Vijeo Designer projects?

Both the number of variables you can share and the number of targets you can share variables with, are limited.
The limits depend on target's reference code (derived from performance limitations).

Runitme Limitation (extract)
  HMIG5U / HMIG5U2 / iPC /
XBTGTW / HMIGTW
HMIG3U / XBTGC / XBTGT / XBTGH / HMIGTO /
HMISTO / HMISTU / HMISCU / HMIGK
XBTGK
Number of Variables you can share (recommended) 400 300 300


 


 



The Maximum Number of Shared Variables is the recommended maximum number of variables that is shared at any one time NOT the maximum number of Sharing-enabled (Read-only or Read/Write) variables. In other words, the number of variables that you set to Read-Only or Read/Write has no limits; only the number of variables that are accessed by other targets is limited. Performance may become an issue if you exceed the recommended maximum

(derived from VJD 6.2 SP6 Online Help)

What size cables fit into the 4CB3125/10?

If the cable is Rigid/ Semi Rigid the 4CB3125/10 breaker will take a cable from 1mm²- 50mm².

OR

If the cable is Flexible or Ferrule the 4CB3125/10 breaker will take a cable from 1.5mm²- 35mm².

Is there a slim weatherproof enclosure cover?

Yes, the part number is 223H
Some of the key features are:
  • 84 mm Mounting centre apart (94 x 50 mm)
  • Horizontal
For further information please visit https://www.clipsal.com/Trade/Products/ProductDetail?catno=223H


I need a remote switch for my TR series Inverter/Charger

The TR remote (989-1060) is discontinued. It is possible to make your own switch using RJ12 plugs and 6-conductor phone cord. 
Switch is momentary contact. 
Diagram attached. 

What is the Tesys D-Line maximum frequency for Power Poles?

Issue:
Checking on the maximum Hz voltage that can be applied to the Tesys D-line contactors.

Product Line:
Tesys D Contactors

Environment:
IEC Contactors and Starters

Cause:
Product Characteristics

Resolution:
These units have been tested for frequencies 25Hz to 400hz within the operational current of the device .  No testing has been done beyond this frequency.

Error: An unknown error occurred during genie iteration. See the 'Windows Event Log' for details - PSE 8.1 One Line Configuration Utility


Issue
An error message:  An unknown error occurred during genie iteration.  See the 'Windows Event Log' for details  is seen when trying to open the One Line Configuration Utility for PSE 8.1.



Product Line
Power Scada Expert 8.X

Environment
One Line Configuration Utility
Advanced OneLine

Cause
The One Line Configuration Utility opens and updates the AdvOneLine.csv file that is located in the AdvOneLine project folder.  If the AdvOneLine.csv file is already opened, the tool will throw this error.

Resolution
Find any instance of AdvOneLine.csv and close it.  Once it's closed, rerun the One Line Configuration Utility from the Project Editor.

SoMachine (v4.3) Gateway cannot start

Sometimes one of the components needed by SoMachine Gateway is not properly installed or was somehow damaged after installation.
As it is common component with other tools the XBTZ935 cable driver gets damaged. Try the following:
1) From Control Panel\All Control Panel Items\Programs and Features, uninstall XBTZG935 cable driver service 
2) Start SoMachine Configuration Manager, uninstall Gateway,
3) Restart PC
4) Install Gateway and all components it requires.

Notes :
-You will need the SoMachine v4.3 installation media.
-Earlier versions of SoMachine Gateway can benefit also.

Does a 2025RCD30-WE fit into a 255 weather protected box?

Yes, the 2025RCD30-WE will fit into a 255 weather protected box.The 2025RCD30-WE is 27mm deep and the 255 has 35mm depth. The bottom screwed plug will need to be shortened if not used as a cable entry.

Is part no 255 available in shallow version

There is not a shallow version of part no 255 available

for more information on this part please refer to https://www.clipsal.com/Trade/Products/ProductDetail?catno=255


User-added image

Vamp 255 communications maps

Issue    
Need the register list for my VAMP relay.

Product Line
Vamp 255

Resolution
See the attached files for the VAMP 255 communications maps, this includes maps for:
Modbus
Profibus
SPA bus
DNP3
IEC101
IEC103
Modbus Master
ProfibusDP

Note:  Latest information is available in m.vamp.fi

What is the sampling frequency of Sepam series 80?


The sampling frequency is controlled by the network frequency, between 25Hz and 65Hz.

For measurements (except for RMS and THD) and protection functions, the sampling frequency is 12 times the electrical network frequency, i.e. 600 Hz for 50 Hz networks, 606 Hz for 50.5 Hz networks and 720 Hz for 60 Hz networks.

For RMS and THD measurements, the sampling frequency is 36 times the electrical network frequency

Re-published to revised security level: 18 June 2008 by DRM

Applies To: Sepam Series 80

Public

All content © 1992-2008 Schneider Electric


Legacy KB System (APS) Data: RESL166600 V2.0, Originally authored by LaVI on 06/20/2008, Last Edited by DaMi on 06/20/2008
Related ranges: Sepam series 80

Need a direct link to Tables/Alarms/Trends/Diagrams/Reports parts of Power Monitoring Expert's Web Apps

Issue 
What is the direct PME web applications link to Alarms, Trends, Diagrams, Reports, or Tables

Product Line
Power Monitoring Expert 7.2.1, 7.2.2, 8

Environment
Web Applications

Cause
By default, Web Applications opens in Dashboards but by using the links below, one can directly log into Alarms, Diagrams, Reports, Tables, or Trends.

 
Resolution
The user can use the following links for each of the tabs.  NOTE: The /?application portion of the URL is case sensitive.

Diagrams: https://computername/web/?application=Diagrams 
Tables: https://computername/web/?application=Tables 
Alarms:https://computername/web/?application=Alarms 
Reports: https://computername/web/?application=Reports
Trends: https://computername/web/?application=Trends 

Why can't I acknowledge alarms from the Global Event Viewer in Vista in StruxureWare Power Monitoring 7.0?

From the StruxureWare Power Monitoring 7.0.1 User Guide:
Acknowledging Alarms
The alarm acknowledgement function is now available only in the Alarms application in the Web Applications component. See the online help for the Alarms for information about acknowledging alarms.
Every type of event has a prioritized value that identifies its relative significance on a scale of 0 (zero) to 255. By default, Vista identifies any event with a priority of 128 (default) or greater as an alarm.

Keywords: SPM, PME, Power Monitoring Expert, SPM7, AAV, active alarms viewer, cannot acknowledge all, disabled


Legacy KB System (APS) Data: RESL210004 V1.0, Originally authored by AnVa on 12/13/2012, Last Edited by AnVa on 12/13/2012
Related ranges: Power Monitoring 7.0

Will Zen switch plate fit in 223H and 255 enclosures?

Yes, Zen switch plates will fit in 255 as it has a depth of 77mm. It will not fit in 233H as it has a depth of 29mm only.

For further information, please visit 
https://www.clipsal.com/Trade/Products/ProductDetail?catno=223H

https://www.clipsal.com/Trade/Products/ProductDetail?catno=255

 

What is the min/max load on PDL 624TM?

Maximum Load: 450W, 1.8A resistive. Minimum Load: 20W, 0.1A resistive
https://www.pdl.co.nz/product-details.aspx?rcat=products&catid=0&id=1924

How to add a Lantronix UDS1100 Ethernet Gateway Site in PME

Title
How to add a Lantronix UDS1100 Ethernet Gateway Site in PME

Issue
Unable to communicate to a Lantronix UDS1100 using the default Lantronix MSS 3001 port.

Product Line
ION Enterprise, SPM, PME, Lantronix

Environment
ION Enterprise, SPM, PME

Cause
Different model numbers of the Lantronix devices use different ports for communication.
The Lantronix MSS devices use port 3001 for channel 1 and 3002 for channel 2.
Lantronix UDS, CoBox, XPress, and XPort use 10001 for channel 1 and 10002 for channel 2.

Resolution
When adding the Ethernet Gateway Site for the Lantronix UDS1100:
1.) Add the site in Management Conslole
a.) Select Sites
b.) Right click on the right field and select New/Ethernet Gateway Site
c.) Enter the IP address for the gateway
d.) For TCP/IP Port type 10001 (ignore the fact that this may not be available in the dropdown and just type the numbers)


2.) Login to the Lantronix Web page of the UDS1100 by entering the IP addess on the web brower, it will ask for a username/password, you can ignore it and just click on login
3.) Configure the Protocol, local Port and Port Settings to match downstream serial device. Example is given below.



4.) Return to Management Console> Sites
5.) Right click you site created above and select Connect
6.) Click Stay Connected

The site should connect to the lantronix and then show Connected in Management Console

How to fix HTTP Error 405 Method Not Allowed in ClearSCADA Mobile?

A common cause of this error is the WebDAV Publishing feature being installed as a part of Internet Information Services. This feature may block certain HTTP verbs needed for ClearSCADA Mobile to function correctly. Please follow the steps below for resolution:
 

1. Launch Internet Information Services (IIS) Manager and locate the ClearScadaMobile website.
2. Click on the ClearScadaMobile website and open Handler Mappings by locating this feature in the IIS section, right clicking on it and selecting Open Feature.
3. In Handler Mappings, locate the WebDAV handler and double click on it to view its properties.
4. In the Edit Module Mappings window, click on Request Restrictions.
5. Once the Request Restrictions window is shown, click on the Verbs tab, select All Verbs and click OK to apply the change.
6. Select the ClearScadaMobile website again and restart the website by clicking on Restart in the Manage Website section.
7. Restart the mobile application in the mobile device and try to connect again.

The mobile website is named ClearSCADA in ClearSCADA 2015 R1.
It is named ClearScadaMobile in other versions of ClearSCADA.





 

What is the MCS025 Sync-Check Module

Issue
What is the MCS025 Sync-Check Module for the Sepam 80 Series

Product Line
Sepam 80 Series
MCS025 Sync-Check Module

Environment
Digital Relays

Resolution
The optional MCS025 module performs the Sepam Series 80 sync-check function (i.e., checks the upstream and downstream voltages of a circuit breaker to ensure safe closing ANSI 25) for substation, transformer, generator and bus applications.
It checks the differences in amplitude, frequency, and phase between the two measured voltages, and takes into account dead line/bus conditions. Three relay outputs can be used to send a Close Enable signal to several Sepam Series 80 relays. The circuit-breaker control function of each Sepam Series 80 relay takes this close enable into account.

The settings for the sync-check function and the measurements carried out by the module are accessed by the SFT2841 setting and operating software. They are similar to the other settings and measurements for the Sepam Series 80.

The MCS025 module is equipped with the following:
CCA620 connector for connecting the relay outputs and the power supply
CCT640 connector for voltage connection
CCA785 cord for connection between the module and the Sepam Series 80 base unit




see attachment

63230-216-244_MCS025_ InstallSheet.pdf

 

What is the difference between a photoelectric smoke alarm and an ionisation smoke alarm?

The following information was taken from fire.nsw.gov.au. Please visit the website (click here) for further information.

The two main ways that smoke alarms detect smoke are photoelectric and ionisation. Research indicates that photo-electric smoke alarms may be more effective at detecting smouldering fires and fires starting in areas remote from smoke alarms, and that ionisation smoke alarms may be more effective at detecting flaming fires. Both types of fires may occur in buildings where people sleep. FRNSW recommends where possible that photo-electric smoke alarms are installed in paths of travel between sleeping areas and exits to the open air or to common corridors.

Photoelectric smoke alarms

Photoelectric smoke alarms 'see' the smoke. They detect visible particles of combustion, eg smouldering cigarette smoke. They respond to a wide range of fires, but they are particularly responsive to smouldering fires and the dense smoke given off by foam filled furnishings or overheated PVC wiring. 

Ionisation smoke alarms
Ionisation smoke alarms 'feel' the smoke. They detect invisible particles of combustion, eg from cooking toast. They activate more quickly for fast, flaming fires with little visible smoke.

Can you get the flap / lid only for the 255 weatherproof enclosure?

Yes, the part number for the flap / lid is 255FLAP-TR

Video : How to use ION OPC Test Client to read OPC tags in PME?

Issue
How to use ION OPC Test Client (the built-in OPC Test Client utility in PME) to read OPC tags off of the devices that are connected to the PME.

Product Line
ION Enterprise 5.6, 6.0, 6.1
StruxureWare Power Monitoring 7.0.x
Power Monitoring Expert (PME) 7.2.x, 8.x

Environment
OPC Test Client utility

Resolution
Below is a video showing how to use the OPC Test Client to read OPC tags off of the devices connected with the PME.

Why is my Conext SW Inverter/Charger faulting with F2 (AC output Over voltage)?

Conext SW Inverter/Charger is faulting with F2

Problem: Conext SW is faulting with F2(AC Output Over Voltage)
Solution:  Check the firmware and make sure it is 3.0.
The trip limits on the 3.0 were increased so it is most likely the CSW has older firmware.
 
 

What is the part number for Iconic series HDMI mechanisms?

The part number for Iconic HDMI mechanisms are:

40HDMIS -  Clipsal Iconic - HDMI straight socket
For further information, please visit https://www.clipsal.com/Trade/Products/ProductDetail?catno=40HDMIS-TN


40HDMIA - Clipsal Iconic - HDMI Angled socket
For further information, please visit https://www.clipsal.com/Trade/Products/ProductDetail?catno=40HDMIA-TN

What is the harmonized tariiff schedule (HTS code) for a XBTZGM128 Compact Flash card?

HTS stands for Harmonized Tariff Schedule. This reference is needed for International Trade purposes.
The HTS code for XBTZGM128 Compact Flash card is 8538.90.80.80.

Why is the subscription report says successful when sent to the printer but nothing prints?

Issue
Unable to print subscription reports from PME/Web Applications/Reports even when it says it was successful.
If the report is saved to the desktop, it prints OK.
From the Desktop works because it is using Windows not PME.

Product Line
All versions of Power Monitoring Expert (PME)

Environment
Power Monitoring Expert
Printing Reports


Cause
The installed printer does not allow printing from subscription reports in PME/Web Applications/Reports.

Resolution
In order to print pdf subscription reports, a TRUE PDF printer needs to be installed.
The printer specifications needs to include PDF under the  Page Description Languages as shown below.


Page Description Languages (PDL)
PCL® 5c, PCL® 6, PDF direct, PostScript 3 compatible 

Does the 3105LSIM come with a 24V power supply?

No that is designed to go in conjunction with the 3105SIMPS (stereo input module that is Discontinued and no replacement) which does come with the 24V power supply.

What are the part numbers of IP66 rated switches in the weathershield range that can be surface mounted?

The part numbers of IP66 rated switches in the weathershield range that can be surface mounted are:
WSF226B - 1 Gang, 1 way/2 way, 250V 16A
WSF226/2B - 2 Gang, 1 way/2 way, 250V 16A
WSF226/3B - 3 Gang, 1 way/2 way, 250V 16A
WSF226/20B- 1 Gang, 1 way/2 way, 250V 20A
For further information, please visit:
https://www.clipsal.com/Trade/Products/ProductDetail?catno=WSF226B
https://www.clipsal.com/Trade/Products/ProductDetail?catno=WSF226/2B
https://www.clipsal.com/Trade/Products/ProductDetail?catno=WSF226/3B
https://www.clipsal.com/Trade/Products/ProductDetail?catno=WSF226/20B
User-added image
User-added image
 

Does the Clipsal 31E2PUDM2 PB dimmer capable of 2 way Switching?

No, it is a one way switch and cannot be used in a two way switching situation.
 

Web Applications Log In fails with an error message in SPM/PME

Issue
When logging into the Web Applications the user provides a known correct User name and Password however the login is unsuccessful.

SPM 7.0.x Login Screen with error message "Log on unsuccessful":



PME 7.2.x Login Screen with error message "The user name or password you entered is invalid. Please check and try again.":


 
PME 8.x Login Screen with error message "The user name or password you entered is invalid. Please check and try again.":



Product Line
StruxureWare Power Monitoring 7.0.x (SPM 7.0.x)
Power Monitoring Expert 7.2.x (PME 7.2.x)
Power Monitoring Expert 8.x (PME 8.x)
 
Environment
Web Applications Login
 
Cause
There are several possible causes for the Web Applications failed login attempt. Below are some common causes of the login failure.

The SQL Ionedsd user account does not have the correct permissions.

OR

The WebRealTime.svc may be unable to start due to lack of memory.

Resolution
*Warning: Irreparable database damage can occur. This procedure should only be performed by users familiar with SQL Server Management Studio. Databases should be backed up prior to performing this procedure.* 

Resolution 1:
Make sure that the browser version is supported in the PME version that is installed. Check supported browser version in FA211703

Resolution 2:
For the ionedsd user, add the NOM_DSD_Reader role for ION_Network and the ION_DSD_Reader role for ION_Data by opening SQL server Management studio and going to properties on the ionedsd account.




Resolution 3:
Navigate to: https://localhost/Webservices/WebRealTime.svc and verify that there are no errors loading the page. If error contains a message that the service is unable to start due to lack of memory, open the Task Manager and identify the processes that are using high amounts of memory. Identify if there are programs that can be stopped to free up memory. Verify that SQL's memory is limited by following FA213995.

Resolution 4:
Within the ApplicationModules database Views, make sure that the "Configuration.ConfigurationSettings" keys point to the correct locations as shown below in red. The server should be set to the database server for distributed system and the local machine for standalone configurations:

Key - IonDataConnectionString
Value - server=localserver\ION;database=ION_Data;uid=ionedsd;pwd=exw1BStLAmzokMLd4uiXLouELuCl037YUD;MultipleActiveResultSets=True

Key - IonNetworkConnectionString
Value - server=localserver\ION;database=ION_Network;uid=ionedsd;pwd=exw1BStLAmzokMLd4uiXLouELuCl037YUD;MultipleActiveResultSets=True

Resolution 5:
Grant permissions to Connect SQL. To do this, navigate to Microsoft SQL Management Studio. Then go to the security folder. When the security folder is expanded, right click on ionedsd and select the ionedsd properties. When the ionedsd properties pop up window is available select the securables page. From here scroll down under the explicit tab until you find Connect to SQL. Check the box under Grant. Select OK. 



Resolution 6:
The value in the [Signature] field within the [DataSourceBus].[DataSource] table found in the ApplicationModules database needs to be copied to the following file:
C:\Program Files (x86)\Schneider Electric\Power Monitoring Expert\Applications\bin​\DataServicesHost.config



*Warning: Take backups of any files prior to modifying them. Ensure the backups are in a location that will not be overwritten (i.e. the Desktop).

The setting within the DataServicesHost.config file as shown below from a test PME system must match the value found in the database.  If it doesn't, you can manually edit DataServicesHost.config to match the signature field value in the database.

<?xml version="1.0"?>
<configuration>
  <appSettings>
    <add key="ServiceHostId" value=""/>
    <add key="Role" value="DataBus,IonEnterpriseDataSourceDriver,Hierarchy"/>
    <add key="DataSourceDriverInstance" value="ION Enterprise-Default" />
    <add key="DataSourceSignature" value="2e7666ed-c948-46ad-9994-6cd9623c276f"/>
  </appSettings>
</configuration>
 
Resolution 7:
If the system requires a fully qualified domain name (ie https://pme.schneider-electric.com/web) to access the webpage, then the following database entries may need to be updated to allow for javascript to be loaded to the webpage and encode the user's password: ApplicationModules > Views > Configuration.ConfigurationSettings and ION_Network > Views > dbo.vCFG_ConfigItems.

To update the aforementioned database entries, perform the following:
  1. Login into SQL Server Management Stuido
  2. Navigate to ApplicationModules > Views
  3. Right-click on Configuration.ConfigurationSettings and select Edit Top 200 Rows
  4. Locate the entry where
    • ItemType = WebFramework
    • Item = Server
    • Key = LocalServerAddress
  5. Update this entry to reflect the fully qualified domain name.
For example, update the entry to be something like https://pme.schneider-electric.com/web.
  1. Navigate to ION_Network > Views
  2. Right-click on dbo.vCFG_ConfigItems and select Edit Top 200 Rows
  3. Locate the entry where
    • Module = Reporting
    • Category = General Settings
    • Item = WebServiceURL
  4. Update this entry to reflect the fully qualified domain name.
For example, update the entry to be something like https://pme.schneider-electric.com/ionreportdataservice/ReportDataService.asmx.
  1. Perform an IISReset and restart the ApplicationModules services

Unable to save Realflo file and missing .TFV and .TFX files

If getting these following Error or issues when saving the Realflo files.


Solutions:
Verify the MSXML files in your programs and features under the control panel if missing.

If these files doesn't appear into the programs and features.

Download and install the msxml4.dll.
https://schneider-electric.box.com/s/g5hvexhp9vjniw2lyyajl5b4mkt2gjz2

Copy the file msxml.msi to the local PC and run it as administrator for the customer which have no MSXML 4.0 Parser shown in Control Panel. After that check the control panel again to see if it is show up. Than try to run Realflo again.
 

Configure ClearSCADA as EWS Server and EWS Client

This is a brief article to show how ClearSCADA can be configured as an EWS server and as an EWS client that uses the Advanced EWS driver to communicate with the EWS server. 


ClearSCADA as EWS Server


To configure a ClearSCADA system to allow EWS clients to retrieve data from it please follow these steps:

1. Create a ClearSCADA User to be used by EcoStruxure Web Services.

2. Enable Advanced EWS Web Services and specify the Advanced EWS user account created in the previous step by right clicking on the Root object and going to Properties -> EcoStructure Web Services. Make sure to configure user security appropriately to allow the user to Read and, if needed, to Control.

 

ClearSCADA as EWS Client


In order for a ClearSCADA system to act as an EWS client, the ClearSCADA application needs to use the Advanced EWS driver. The Advanced EWS driver must be installed and licensed on the ClearSCADA server. Please follow the steps below to configure ClearSCADA as an EWS client:

1. Check License Details to make sure your ClearSCADA license allows for the Advanced EWS driver. Otherwise please contact a Schneider Electric representative in your area or fill out this form.

2. If the license supports the Advanced EWS driver, check whether the driver is installed on the ClearSCADA host. Use Status -> General -> Modules dialog to check if the driver is installed and ready. If the driver is not installed, run the ClearSCADA installer and select the Advanced EWS driver from the list.

3. Once the Advanced EWS driver is installed and licensed, create an Advanced EWS Server object and specify the EWS server URL.

 If you are connecting to another ClearSCADA system acting as an EWS server, the URL should be of the following format: https://<server>:<port>/webservices/secorp or https://<server>:<port>/webservices/secorp

4. Create a Group and add the Server object to the Servers list. Configure Scanning Intervals for Current, Historic and Forecast data.

5. Create an Advanced EWS point and browse for the target in the Current Data Id and History Data Id fields. 

6. You should now see the point updating.

Video: How do you create and use a DTX file in Unity Pro?

Issue:
Creation and usage of the DTX file in Unity Pro

Product Line:
Unity Pro

Resolution:

The DTX file is a very useful tool that allows the user to capture the current values stored in %MW as well as unlocated variables. The data stored in the DTX file can be used to restore process data after an outage or capture tuning tuning values for start up. You can make any number of DTX files which would allow you to introduce different process recipes .

The following video will demostrate how to create and use the DTX file.

 

What is the part number of a Zen double outlet with 32A extra switch mechanism?

Below part numbers are needed to build a Zen double outlet with 32A extra switch mechanism:
Z4025XUA - A double Socket Outlet 10A 250V Less Extra Switch
60R32 - Switch Mechanism 32A 250V. 60R32COOK is the part number of the 32A, 250V switch mechanism marked COOKER. (The mechanisms are available in ZW (Zen White) or ZB (Zen Black) to suit the Zen plate)..

https://www.clipsal.com/Trade/Products/ProductDetail?catno=Z4025XUA
https://www.clipsal.com/Trade/Products/ProductDetail?catno=60R32
https://www.clipsal.com/Trade/Products/ProductDetail?catno=60R32COOK
 

Where can I find a Power Monitoring Expert (PME) 8.2 web applications demo site?

Issue:
Is there a PME demo on the internet?

Product Line:
Power Monitoring Expert 8.2

Environment:
Web Applications

Resolution:
Yes, there is a demo site with access to PME 8.2 web applications.

PME 8.2 - https://www.pmedemo.biz/
user:  guest
password: 0

You have a limited view of the web applications with this user account but you can still demo all components of web applications.
Show More