link neutral 7hole

Max 4 Neutral Active Meter Links, 7 Hole, For 150mm² Cables, Front Wiring

Catalogue Number: L7/150
link neutral 7hole
Retail
$315.26
RRP (Inc. GST)

Specifications

hide show
Product brand
Clipsal
Range of product
Blue Point
Product or component type
neutral link
Cable cross section
150-150 mm²
[In] rated current
370 A
[Ue] rated operational voltage
500 V
Connector type
screw terminals
REACh Regulation
Free of Substances of Very High Concern above the threshold
EU RoHS Directive
Compliant
Mercury free
Yes
RoHS exemption information
Yes
China RoHS Regulation
Product out of China RoHS scope. Substance declaration for your information

Frequently Asked Questions

hide show

What is the tunnel size of L7/150 and what size cables do they take?

L7/150 is 500V 370A 7 Hole Front Wiring Neutral Link. Black base and cover.
Dimensions: 162 x 53 x 55mm.
2 tunnels, 17mm diameter accommodate 150mm2 cable.
1 tunnel, 15.5mm diameter accommodate 120mm2 cable.
2 tunnels, 10mm diameter accommodate 50mm2 cable.
2 tunnels, 5.9mm diameter accommodate 16mm2 cable.
Supplied with Allen key.
For further information, please visit https://www.clipsal.com/Trade/Products/ProductDetail?catno=L7/150

What is the part number for link bar to accommodate 150mm2 cable?

The link bar part number is L7/150 (neutral) or L7/150R (active)
They will accommodate up to 150mm2 cable.

L7/150 Neutral Link, Maxi, 7 Hole, 370A                     L7/150R Active Link, 7 Hole, 370A,        
Front Wiring, Black Base and Cover                           Front Wiring, Red Base and Cover       

For further information, please visit:
https://www.clipsal.com/Trade/Products/ProductDetail?catno=L7/150
https://www.clipsal.com/Trade/Products/ProductDetail?catno=L7/150R

 

Does Clipsal have a Link Bar with at 13 tunnels and 1 x 50mm and 3 x 16mm tunnels?

Yes the L13/150 will suit those requirements.

How to perform MSET on a BPH motor using Lexium 17/15 Servo Drive?



Issue:  Although the BPH motors that are used with the Lexium 17 and 15 range of Servo drives are factory MSET, occasionally there may be a need to MSET this in the field due to commutation error being reported. 


Product Line: Lexium BPH


Environment:


Cause: Due to an incorrect offset value set in the drive, the drive may report a F25, commutation error.


Resolution: This resolution discusses the MSET procedure for a BPH motor with a Lexium 17/15 series drive.

 
Proper commutation and position feedback are required to interface a particular servo drive and motor combination. When using Schneider Electric BPH motors and Lexium drives, this setup (or “characterization”) process has been completed and verified for the user at the factory. Occasionally there may be a need to MSET the BPH motor and this is detailed in this procedure.
 
Perform the following steps, as described, and in the order presented, to complete the MSET procedure. 
 
1.    Disconnect the Motor from the Mechanical Load
2.    Electrical Connections
A.   Verify that the required electrical connections for drive power, logic power, motor power and resolver are as described in the Lexium drive user manual.
B.   Apply 24VDC logic and AC input power to confirm proper drive startup sequence and self-checks.
 
 Follow this MSET procedure only if the drive firmware is ver 5.51 and above.
 
 Connect to the drive using Hyperterm…
 
  1. Type OPMODE followed by Enter – note down the Opmode (xx) the drive is set to.
 
  1. Type OPMODE 2 followed by Enter – switch to digital torque mode
     C.     Type 'EN' followed by Enter.

     D.     Type "Zero" followed by ENTER - Motor shaft will jump to nearest pole. MPHASE value is automatically set.
 
  
  1. Type SAVE
 
  1. Type OPMODE xx followed by enter ( where xx is the default value that was originally set for the application.)
 
     G.    Type COLDSTART (the drive will reboot)
This completes the MSET procedure.