Quantcast

Medilec Isolation Transformers, 240V, 3.6kVA, Encapsulated

Medilec Isolation Transformers, 240V, 3.6kVA, Encapsulated

Medilec Isolation Transformers, 240V, 3.6kVA, Encapsulated

Item Number: E14/36/2

Retail
$4,141.27
RRP (Inc. GST)

Datasheet

Barcode

Qty UoM EAN Colour
-
-
-

Specifications

Design

Range of product

  • ESP Metal Plate Series
  • Series E14
  • Medilec
    • Product brand

      Clipsal

      Physical

      [In] rated current

      15 A

      Others

      Package 1 Height

      26.5 cm

      Package 1 Length

      28.5 cm

      Package 1 width

      30 cm

      Primary voltage

      240 V AC

      Secondary voltage

      240 V AC

      Rated power in VA

      3600 VA

      Package 1 Weight

      40 kg
      Show all specifications

      Frequently Asked Questions

      hide show

      What is the difference between a encapsulated and a non encapsulated isolation tansformer in the medilec range?

      The encapsulated isolation transformer has its windings covered in heat-cured epoxy resin to reduce noise and prevent ingress of moisture and dust. Where for the non-encapsulated model has visible bare windings which are subject to dust and moisture.
      Encapsulated - E14/36/2 & E14/48/2
      Non Encapsulated - E14/36/3 & E14/48/3 
      For further information see link https://www.clipsal.com/search?q=E14

      Is part code E05/36/2 still available in NZ

       Yes it is still available but it is an indent

      Can the Primary and Secondary be run together on the e14/36/3

      - Can the Primary and Secondary be run together?
      Preferably not - but this is impacted by the distance they are run together. If the distance is short, i.e. a few metres then not a problem. If it is more distance then need to segregate. It is difficult to give an exact answer as there are dependencies. If they were separate by 1m then any distance would be ok.

      - Is segregation required, and if so what is the advised segregation distance and type (conduit etc)
      As above - at least 1m would meet all circumstances. Type of conduit does not really matter as the distance provides the segregation rather than any shielding from conduit.
      Please see following link for further information and related products
      https://www.clipsal.com/Trade/search-results?q=e14/36/3

      What replaces the line isolation and overload monitor E05/36/2 and E05/48/2?

      The part number for the line isolation and overload monitor is MLHG6. The MLHG6 line isolation and overload monitor replaces both E05/36/2 and E05/48/2.
      The MLHG6 requires a wall box, the part number for the wall box is MLHG6B-AU.
      Some of the key features are:
      • Programmable for current monitoring up to 100A
      • In-built test / verification module
      • Tracks data history of operational mode and faults
      • Fully approved to AS/NZS4510:1999 Isolated Electrical Supplies for Medical Uses
      • Meets requirements for AS/NZS3003:2011 Electrical Installations – Patient Areas of Hospitals
      • Potential to integrate into BMS
      For further information please visit https://www.clipsal.com/Trade/Products/ProductDetail?catno=MLHG6
       

      What are the dimensions of wall box to suit 14/30/7

      Dimensions of wall box 324mm x 97mm x 58mm Part no 164/7

      What is the wall box to suit the B4/30/2 ?

       The part number for the wall box is 164/2
      Show More