Quantcast

Max 4 Connector Blocks, 40A, 2 Way, Triple Entry Single Unit

Max 4 Connector Blocks, 40A, 2 Way, Triple Entry Single Unit

Max 4 Connector Blocks, 40A, 2 Way, Triple Entry Single Unit

Item Number: BP603

Retail
N/A
RRP (Inc. GST)

Datasheet

Barcode

Qty UoM EAN Colour
-
-
-

Specifications

Design

Product brand

Clipsal

Range of product

Blue Point

Product or component type

connector block

Physical

[In] rated current

40 A

Connector type

screw terminals

EU RoHS Directive

Compliant

Mercury free

Yes

RoHS exemption information

Yes

China RoHS Regulation

Product out of China RoHS scope. Substance declaration for your information

Others

Package 1 Height

19 mm

Package 1 Length

36 mm

Package 1 width

36 mm

Cable cross section

10-10 mm²

Package 1 Weight

31 g
Show all specifications

Frequently Asked Questions

hide show

Is part number BP30F still available?

No. Unfortunatelythis part is no longer available nor a replacement.

Video: Back-UPS CS, RS & XS - Manual Adjustment for Sensitivity

Issue:

UPS will not operate on utility power or may be clicking between utility and battery power.


Product Line:

Back-UPS RS/XS & Back-UPS CS (4-LED Interfaces)


Environment:

All models & serial numbers


Cause:

This may be caused by one of the following conditions;
  • Low Voltage / Sag
  • Black-out
  • High Voltage / Over-Voltage
  • Frequency is out of range
  • Total Harmonic Distortion

Resolution:

The following video details the process for manually adjusting the Back-UPS RS & XS or Back-UPS CS system's AC Input Sensitivity.
 

What does a -1603 error indicate in Concept?

This error usually occurs when trying to go online to a PLC and is usually caused by one of the following:
1/ Expansion Size in Peer Cop needs to be decreased. This must be done offline.
2/ If it is a Hot Standby system, either no CHS or HSBY loadable configured or heap size is too large.
3/ Memory partitions maybe incorrect or may be illegal for controller type.


Legacy KB System (APS) Data: RESL1987 V1.0, Originally authored by on , Last Edited by on
Related ranges: Concept

A customer will connect several motors in parallel for conveyor application, and they will be driven by a ATV68C23N4. However, the total motors' ratin...

Goals and Symptoms

A customer will connect several motors in parallel for conveyor application, and they will be driven by a ATV68C23N4. However, the total motors' rating current is less than ATV68C23N4's current. How to setup the motor data in Menu B3 for this case? Is there any particular parameter setting need to be configured for this motor parallel case?

Causes and Fixes

For this application there is some restrictions :

- need to have same motors
- same cabe lenght for each motor

However, for the B3 menu :
B3.00 = global power ( sum of motors )
B3.01 = global current
B3.02 = nominal voltage
B3.03 = nominal frequency
B3.04 = nominal speed
B3.05 = nominal network voltage

And make a tune only if you have exactly same motors.


Legacy KB System (APS) Data: RESL161617 V1.0, Originally authored by on , Last Edited by on
Related ranges: Altivar 68

Does Schneider Electric offer a replacement for the Berger Lahr WPM-311 controller?

The entire product line of WPM-311 type controllers from Berger Lahr are obsolete and no longer available
Schneider Electric does not offer a drop in replacement.

The Berger Lahr WPM311 uses a special programming environment which was unique to Berger Lahr ( Depending on the firmware, Bpro3 programming system or ProOed3 Programming system )

The WPM311 is a 4 axis motion controller that utilizes pulse/direction type outputs which were most commonly used to interface with stepping motor drives.

So to replace the WPM311 you will have to not only find a controller that is capable of controlling multiple axis, but you will also have to write a motion program that duplicates the current application process.

You may try contacting the OEM machine builder, they may have spare WPM311 controllers or they may have already developed a retrofit solution.  

Service is still available at the Schneider Electric Repair Center in Greensboro NC


rev 2-20-18

Does Schneider Electric offer a replacement for the Berger Lahr WPM-311 controller?

The entire product line of WPM-311 type controllers from Berger Lahr are obsolete and no longer available
Schneider Electric does not offer a direct replacement.

The Berger Lahr WPM311 uses a special programming environment which was unique to Berger Lahr ( Depending on the firmware, Bpro3 programming system or ProOed3 Programming system )

The WPM311 is a 4 axis motion controller that utilizes pulse/direction type outputs which were most commonly used to interface with stepping motor drives.

To replace the WPM311 you will need a controller that is capable of controlling multiple axis, and you must write a motion program that duplicates the current application process.

You may try contacting the OEM machine builder, they may have spare WPM311 controllers or they may have already developed a retrofit solution.  

Service is still available at the Schneider Electric Repair Center in Greensboro NC.


Rev 8-8-17
Show More