Quantcast

Altivar 71 1.5KW 4.1A 480V 3PH EMC IP20

Altivar 71 1.5KW 4.1A 480V 3PH EMC IP20

Altivar 71 1.5KW 4.1A 480V 3PH EMC IP20

Item Number: ATV71HU15N4

Product Dimensions

Width icon

Width130 mm

Height icon

Height230 mm

Depth icon

Depth175 mm

Datasheet

Barcode

Qty UoM EAN Colour
-
-
-

Specifications

Design

Product destination

  • synchronous motors
  • asynchronous motors

Sustainable offer status

Green Premium product

Warranty

18 months

Range of product

Altivar 71

Product or component type

variable speed drive

Physical

Local signalling

1 LED (red) for drive voltage

Type of cable

  • with a NEMA Type1 kit: 3 wire(s)UL 508 cable at 40 °C, copper 75 °C / PVC
  • with an IP21 or an IP31 kit: 3 wire(s)IEC cable at 40 °C, copper 70 °C / PVC
  • without mounting kit: 1 wire(s)IEC cable at 45 °C, copper 70 °C / PVC
  • without mounting kit: 1 wire(s)IEC cable at 45 °C, copper 90 °C / XLPE/EPR

Supply

  • internal supply for reference potentiometer (1 to 10 kOhm): 10.5 V DC +/- 5 %, <10 ma,="" protection="" type:="" overload="" and="" short-circuit="">
  • internal supply: 24 V DC (21-27 V), <200 ma,="" protection="" type:="" overload="" and="" short-circuit="">

Protection type

  • against exceeding limit speed: drive
  • short-circuit between motor phases: drive
  • thermal protection: drive
  • motor phase break: motor
  • power removal: motor
  • thermal protection: motor
  • against input phase loss: drive
  • break on the control circuit: drive
  • input phase breaks: drive
  • line supply overvoltage: drive
  • line supply undervoltage: drive
  • overcurrent between output phases and earth: drive
  • overheating protection: drive
  • overvoltages on the DC bus: drive

Insulation resistance

> 1 mOhm 500 V DC for 1 minute to earth

Communication port protocol

  • CANopen
  • Modbus

Connector type

  • 1 RJ45 (on front face) for Modbus
  • 1 RJ45 (on terminal) for Modbus
  • male SUB-D 9 on RJ45 for CANopen

Marking

CE

Height

230 mm

Depth

175 mm

Width

130 mm

Net weight

3 kg

Standards

  • EN 61800-3 environments 2 category C2
  • IEC 60721-3-3 class 3S2
  • EN/IEC 61800-5-1
  • IEC 60721-3-3 class 3C1
  • UL Type 1
  • EN 61800-3 environments 1 category C2
  • EN/IEC 61800-3
  • EN 55011 class A group 1

Product certifications

  • GOST
  • UL
  • CSA
  • NOM 117
  • C-Tick

IP degree of protection

IP20

Relative humidity

  • 5...95 % without condensation conforming to IEC 60068...2-3
  • 5...95 % without dripping water conforming to IEC 60068...2-3

Ambient air temperature for operation

-10...50 °C (without derating)

Ambient air temperature for storage

-25...70 °C

EU RoHS Directive

Pro-active compliance (Product out of EU RoHS legal scope)

Mercury free

Yes

RoHS exemption information

Yes

China RoHS Regulation

X

Environmental Disclosure

ENVPEP050303EN

Circularity Profile

ENVEOLI100207EN

California proposition 65

WARNING: This product can expose you to chemicals including: Lead and lead compounds, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov

Others

Supply voltage limits

323...528 V

Supply frequency

50...60 Hz - 5...5 %

Network frequency

47.5...63 Hz

Speed range

  • 1...100 for asynchronous motor in open-loop mode, without speed feedback
  • 1...1000 for asynchronous motor in closed-loop mode with encoder feedback
  • 1...50 for synchronous motor in open-loop mode, without speed feedback

Speed accuracy

  • +/- 0.01 % of nominal speed in closed-loop mode with encoder feedback 0.2 Tn to Tn
  • +/- 10 % of nominal slip without speed feedback 0.2 Tn to Tn

Torque accuracy

  • +/- 15 % in open-loop mode, without speed feedback
  • +/- 5 % in closed-loop mode with encoder feedback

Transient overtorque

  • 170 % of nominal motor torque +/- 10 % for 60 s every 10 minutes
  • 220 % of nominal motor torque +/- 10 % for 2 s

Braking torque

  • <= 150="" %="" with="" braking="" or="" hoist="">
  • 30 % without braking resistor

Synchronous motor control profile

vector control without speed feedback

Regulation loop

adjustable PI regulator

Motor slip compensation

  • suppressable
  • adjustable
  • not available in voltage/frequency ratio (2 or 5 points)
  • automatic whatever the load

Output voltage

<= power="" supply="">

Insulation

electrical between power and control

Electrical connection

  • terminal, clamping capacity: 2.5 mm², AWG 14 (AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1...LI6, PWR)
  • terminal, clamping capacity: 4 mm², AWG 10 (L1/R, L2/S, L3/T, U/T1, V/T2, W/T3, PC/-, PO, PA/+, PA, PB)

Tightening torque

  • 0.6 N.m (AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1...LI6, PWR)
  • 1.4 N.m, 12.3 lb.in (L1/R, L2/S, L3/T, U/T1, V/T2, W/T3, PC/-, PO, PA/+, PA, PB)

Analogue input number

2

Analogue input type

  • AI1-/Al1+ bipolar differential voltage: +/- 10 V DC 24 V max, resolution 11 bits + sign
  • AI2 software-configurable current: 0...20 mA, impedance: 242 Ohm, resolution 11 bits
  • AI2 software-configurable voltage: 0...10 V DC 24 V max, impedance: 30000 Ohm, resolution 11 bits

Sampling duration

  • 2 ms +/- 0.5 ms (AI1-/Al1+) - analog input(s)
  • 2 ms +/- 0.5 ms (Al2) - analog input(s)
  • 2 ms +/- 0.5 ms (LI1...LI5) - discrete input(s)
  • 2 ms +/- 0.5 ms (LI6)if configured as logic input - discrete input(s)

Response time

  • <= 100="" ms="" in="" sto="" (safe="" torque="">
  • AO1 2 ms, tolerance +/- 0.5 ms for analog output(s)
  • R1A, R1B, R1C 7 ms, tolerance +/- 0.5 ms for discrete output(s)
  • R2A, R2B 7 ms, tolerance +/- 0.5 ms for discrete output(s)

Accuracy

  • +/- 0.6 % (AI1-/Al1+) for a temperature variation 60 °C
  • +/- 0.6 % (AI2) for a temperature variation 60 °C
  • +/- 1 % (AO1) for a temperature variation 60 °C

Linearity error

  • +/- 0.15 % of maximum value (AI1-/Al1+, AI2)
  • +/- 0.2 % (AO1)

Analogue output number

1

Analogue output type

  • AO1 software-configurable logic output 10 V 20-20 mA
  • AO1 software-configurable current 0...20 mA, impedance: 500 Ohm, resolution 10 bits
  • AO1 software-configurable voltage 0...10 V DC, impedance: 470 Ohm, resolution 10 bits

Discrete output number

2

Discrete output type

  • configurable relay logic: (R1A, R1B, R1C) NO/NC - 100000 cycles
  • configurable relay logic: (R2A, R2B) NO - 100000 cycles

Minimum switching current

3 mA at 24 V DC for configurable relay logic

Maximum switching current

  • R1, R2: 2 A at 250 V AC inductive load, cos phi = 0.4
  • R1, R2: 2 A at 30 V DC inductive load, cos phi = 0.4
  • R1, R2: 5 A at 250 V AC resistive load, cos phi = 1
  • R1, R2: 5 A at 30 V DC resistive load, cos phi = 1

Discrete input number

7

Discrete input type

  • LI1...LI5: programmable 24 V DC with level 1 PLC, impedance: 3500 Ohm
  • LI6: switch-configurable 24 V DC with level 1 PLC, impedance: 3500 Ohm
  • LI6: switch-configurable PTC probe 0-6 , impedance: 1500 Ohm
  • PWR: safety input 24 V DC, impedance: 1500 Ohm conforming to ISO 13849-1 level d

Discrete input logic

  • negative logic (sink) (LI1...LI5), > 16 V (state 0), < 10="" v="" (state="">
  • positive logic (source) (LI1...LI5), < 5="" v="" (state="" 0),=""> 11 V (state 1)
  • negative logic (sink) (LI6)if configured as logic input, > 16 V (state 0), < 10="" v="" (state="">
  • positive logic (source) (LI6)if configured as logic input, < 5="" v="" (state="" 0),=""> 11 V (state 1)

Acceleration and deceleration ramps

  • S, U or customized
  • linear adjustable separately from 0.01 to 9000 s
  • automatic adaptation of ramp if braking capacity exceeded, by using resistor

Braking to standstill

by DC injection

Frequency resolution

  • analog input: 0.024/50 Hz
  • display unit: 0.1 Hz

Physical interface

2-wire RS 485 for Modbus

Transmission frame

RTU for Modbus

Transmission rate

  • 4800 bps, 9600 bps, 19200 bps, 38.4 Kbps for Modbus on terminal
  • 9600 bps, 19200 bps for Modbus on front face
  • 20 kbps, 50 kbps, 125 kbps, 250 kbps, 500 kbps, 1 Mbps for CANopen

Data format

  • 8 bits, 1 stop, even parity for Modbus on front face
  • 8 bits, odd even or no configurable parity for Modbus on terminal

Number of addresses

  • 1...127 for CANopen
  • 1...247 for Modbus

Method of access

slave CANopen

Operating position

vertical +/- 10 degree

Functionality

full

Specific application

other applications

Option card

  • communication card for CC-Link
  • communication card for Modbus TCP
  • communication card for Modbus/Uni-Telway
  • overhead crane card
  • communication card for Profibus DP
  • communication card for Profibus DP V1
  • controller inside programmable card
  • communication card for DeviceNet
  • communication card for EtherNet/IP
  • communication card for Fipio
  • I/O extension card
  • communication card for Interbus-S
  • interface card for encoder
  • communication card for Modbus Plus

Noise level

43 dB conforming to 86/188/EEC

Dielectric strength

  • 3535 V DC between earth and power terminals
  • 5092 V DC between control and power terminals

Electromagnetic compatibility

  • 1.2/50 µs - 8/20 µs surge immunity test level 3 conforming to IEC 61000-4-5
  • conducted radio-frequency immunity test level 3 conforming to IEC 61000-4-6
  • electrical fast transient/burst immunity test level 4 conforming to IEC 61000-4-4
  • electrostatic discharge immunity test level 3 conforming to IEC 61000-4-2
  • radiated radio-frequency electromagnetic field immunity test level 3 conforming to IEC 61000-4-3
  • voltage dips and interruptions immunity test conforming to IEC 61000-4-11

Pollution degree

2 conforming to EN/IEC 61800-5-1

Vibration resistance

  • 1 gn (f= 13-200 Hz) conforming to EN/IEC 60068-2-6
  • 1.5 mm peak to peak (f= 3-13 Hz) conforming to EN/IEC 60068-2-6

Shock resistance

15 gn for 11 ms conforming to EN/IEC 60068-2-27

Operating altitude

  • <= 1000="" m="" without="">
  • 1000...3000 m with current derating 1 % per 100 m

Unit Type of Package 1

PCE

Number of Units in Package 1

1

Package 1 Weight

4.186 kg

Package 1 Height

24.5 cm

Package 1 width

24.5 cm

Package 1 Length

30.5 cm

Unit Type of Package 2

S06

Number of Units in Package 2

10

Package 2 Weight

54.86 kg

Package 2 Height

73.5 cm

Package 2 width

60 cm

Package 2 Length

80 cm

WEEE

The product must be disposed on European Union markets following specific waste collection and never end up in rubbish bins

Product specific application

complex, high-power machines

Component name

ATV71

Motor power kW

1.5 kW, 3 phases at 380...480 V

Motor power hp

2 hp, 3 phases at 380...480 V

Maximum motor cable length

  • 50 m shielded cable
  • 100 m unshielded cable

[Us] rated supply voltage

380...480 V - 15...10 %

Network number of phases

3 phases

Line current

  • 5.3 A for 480 V 3 phases 1.5 kW / 2 hp
  • 5.8 A for 380 V 3 phases 1.5 kW / 2 hp

EMC filter

integrated

Assembly style

with heat sink

Apparent power

3.8 kVA at 380 V 3 phases 1.5 kW / 2 hp

Prospective line Isc

5 kA for 3 phases

Nominal output current

  • 3.4 A at 4 kHz 460 V 3 phases 1.5 kW / 2 hp
  • 4.1 A at 4 kHz 380 V 3 phases 1.5 kW / 2 hp

Maximum transient current

  • 6.2 A for 60 s 3 phases 1.5 kW / 2 hp
  • 6.8 A for 2 s 3 phases 1.5 kW / 2 hp

Output frequency

0.1...599 Hz

Nominal switching frequency

4 kHz

Switching frequency

  • 1...16 kHz adjustable
  • 4...16 kHz with derating factor

Asynchronous motor control profile

  • flux vector control (FVC) with sensor (current vector)
  • sensorless flux vector control (SFVC) (voltage or current vector)
  • ENA (Energy adaptation) system for unbalanced loads
  • voltage/frequency ratio (2 or 5 points)

Type of polarization

no impedance for Modbus
Show all specifications

Documents & downloads

hide show
Filter items
  • All

  • Product Brochures

  • CAD Files and Packs

  • Technical Data Catalogues

  • Installation Instruction

  • Product Environmental

  • End of Life Manual

  • Data Bulletin

  • Handout

  • Operating Manuals

  • Technical Drawing

  • eTechPub

  • Marine Certificate

  • Certificates (MSDS)

  • Software - Release

  • DTM Files

Frequently Asked Questions

hide show

What is the part number of the Main Control board for ATV71HD22N4?

Issue:
ATV71HD22N4:  Need to replace the Main Control board ?

Product Line:
ATV71

Environment:
ATV71HO75N4, ATV71HU15N4, ATV71HU22N4, ATV71HU30N4, ATV71HU40N4, ATV71HU55N4, ATV71HU75N4, ATV71HD11N4, ATV71HD15N4, ATV71HD18N4, ATV71HD22N4, ATV71HD30N4, ATV71HD37N4, ATV71HD45N4, ATV71HD55N4, ATV71HD75N4

Cause:
Need the Main Control board part number.

Resolution:
The Main Control board part number for these drive is VX4A71100Y