Variable speed drive with heatsink, single-phase 200,,,240 V 50/60 Hz, 2,2 kW

Altivar 12 Variable Speed Drive ATV12, 2.2kW, 3hp, 200..240V, 1ph

Catalogue Number: ATV12HU22M2
Variable speed drive with heatsink, single-phase 200,,,240 V 50/60 Hz, 2,2 kW
Retail
$767.62
RRP (Inc. GST)

Specifications

hide show
Range of product
Altivar 12
Product or component type
variable speed drive
Product destination
asynchronous motors
Product specific application
simple machine
Assembly style
with heat sink
Component name
ATV12
Quantity per set
set of 1
EMC filter
integrated
Built-in fan
with
Network number of phases
1 phase
[Us] rated supply voltage
200...240 V - 15...10 %
Motor power kW
2.2 kW
Motor power hp
3 hp
Communication port protocol
Modbus
Line current
  • 24 A at 200 V
  • 20.2 A at 240 V
    • Speed range
      1-20
      Transient overtorque
      150-170 % of nominal motor torque depending on drive rating and type of motor
      Asynchronous motor control profile
    • sensorless flux vector control
    • quadratic voltage/frequency ratio
    • voltage/frequency ratio (V/f)
      • IP degree of protection
        IP20 without blanking plate on upper part
        Noise level
        45 dB
        Supply frequency
        50/60 Hz +/- 5 %
        Connector type
        1 RJ45 (on front face) for Modbus
        Physical interface
        2-wire RS 485 for Modbus
        Transmission frame
        RTU for Modbus
        Transmission rate
      • 4800 bit/s
      • 9600 bit/s
      • 19200 bit/s
      • 38400 bit/s
        • Number of addresses
          1-247 for Modbus
          Communication service
        • read holding registers (03) 29 words
        • write single register (06) 29 words
        • write multiple registers (16) 27 words
        • read/write multiple registers (23) 4/4 words
        • read device identification (43)
          • Prospective line Isc
            1 kA
            Continuous output current
            10 A at 4 kHz
            Maximum transient current
            15 A for 60 s
            Speed drive output frequency
            0.5-400 Hz
            Nominal switching frequency
            4 kHz
            Switching frequency
          • 2...16 kHz adjustable
          • 4...16 kHz with derating factor
            • Braking torque
              up to 70 % of nominal motor torque without braking resistor
              Motor slip compensation
            • adjustable
            • preset in factory
              • Output voltage
                200...240 V 3 phases
                Electrical connection
                terminal, clamping capacity: 5.5 mm², AWG 10 (L1, L2, L3, U, V, W, PA, PC)
                Tightening torque
                1.2 N.m
                Insulation
                electrical between power and control
                Supply
              • internal supply for reference potentiometer: 5 V DC (4.75-5.25 V), <10 mA, protection type: overload and short-circuit protection
              • internal supply for logic inputs: 24 V DC (20.4-28.8 V), <100 mA, protection type: overload and short-circuit protection
                • Analogue input number
                  1
                  Analogue input type
                • configurable current AI1 0...20 mA 250 Ohm
                • configurable voltage AI1 0...10 V 30 kOhm
                • configurable voltage AI1 0...5 V 30 kOhm
                  • Discrete input number
                    4
                    Discrete input type
                    programmable LI1...LI4 24 V 18...30 V
                    Discrete input logic
                  • negative logic (sink), > 16 V (state 0), < 10 V (state 1), input impedance 3.5 kOhm
                  • positive logic (source), 0...< 5 V (state 0), > 11 V (state 1)
                    • Sampling duration
                    • 20 ms, tolerance +/- 1 ms for logic input
                    • 10 ms for analogue input
                      • Linearity error
                        +/- 0.3 % of maximum value for analogue input
                        Analogue output number
                        1
                        Analogue output type
                      • AO1 software-configurable voltage: 0...10 V, impedance: 470 Ohm, resolution 8 bits
                      • AO1 software-configurable current: 0...20 mA, impedance: 800 Ohm, resolution 8 bits
                        • Discrete output number
                          2
                          Discrete output type
                        • logic output LO+, LO-
                        • protected relay output R1A, R1B, R1C 1 C/O
                          • Minimum switching current
                            5 mA at 24 V DC for logic relay
                            Maximum switching current
                          • 2 A 250 V AC inductive cos phi = 0.4 L/R = 7 ms logic relay
                          • 2 A 30 V DC inductive cos phi = 0.4 L/R = 7 ms logic relay
                          • 3 A 250 V AC resistive cos phi = 1 L/R = 0 ms logic relay
                          • 4 A 30 V DC resistive cos phi = 1 L/R = 0 ms logic relay
                            • Acceleration and deceleration ramps
                            • linear from 0 to 999.9 s
                            • U
                            • S
                              • Braking to standstill
                                by DC injection, <30 s
                                Protection type
                              • line supply overvoltage
                              • line supply undervoltage
                              • overcurrent between output phases and earth
                              • overheating protection
                              • short-circuit between motor phases
                              • against input phase loss in three-phase
                              • thermal motor protection via the drive by continuous calculation of I²t
                                • Frequency resolution
                                • analog input: converter A/D, 10 bits
                                • display unit: 0.1 Hz
                                  • Time constant
                                    20 ms +/- 1 ms for reference change
                                    Marking
                                    CE
                                    Operating position
                                    vertical +/- 10 degree
                                    Height
                                    142 mm
                                    Width
                                    105 mm
                                    Depth
                                    156.2 mm
                                    Net weight
                                    1.4 kg
                                    Functionality
                                    basic
                                    Specific application
                                    commercial equipment
                                    Discrete and process manufacturing
                                    Power range
                                    2.2-3 kW at 200-240 V 1 phase
                                    Motor starter type
                                    variable speed drive
                                    Electromagnetic compatibility
                                  • electrical fast transient/burst immunity test level 4 conforming to EN/IEC 61000-4-4
                                  • electrostatic discharge immunity test level 3 conforming to EN/IEC 61000-4-2
                                  • immunity to conducted disturbances level 3 conforming to EN/IEC 61000-4-6
                                  • radiated radio-frequency electromagnetic field immunity test level 3 conforming to EN/IEC 61000-4-3
                                  • surge immunity test level 3 conforming to EN/IEC 61000-4-5
                                  • voltage dips and interruptions immunity test conforming to EN/IEC 61000-4-11
                                    • Electromagnetic emission
                                    • radiated emissions environment 1 category C2 conforming to EN/IEC 61800-3 2...16 kHz shielded motor cable
                                    • conducted emissions with integrated EMC filter environment 1 category C1 conforming to EN/IEC 61800-3 2, 4, 8, 12 and 16 kHz shielded motor cable <5 m
                                    • conducted emissions with additional EMC filter environment 1 category C1 conforming to EN/IEC 61800-3 4...12 kHz shielded motor cable <20 m
                                    • conducted emissions with additional EMC filter environment 1 category C2 conforming to EN/IEC 61800-3 4...12 kHz shielded motor cable <50 m
                                    • conducted emissions with additional EMC filter environment 2 category C3 conforming to EN/IEC 61800-3 4...12 kHz shielded motor cable <50 m
                                    • conducted emissions with integrated EMC filter environment 1 category C2 conforming to EN/IEC 61800-3 4...16 kHz shielded motor cable <5 m
                                    • conducted emissions with integrated EMC filter environment 1 category C2 conforming to EN/IEC 61800-3 2, 4, 8, 12 and 16 kHz shielded motor cable <10 m
                                      • Product certifications
                                      • C-Tick
                                      • CSA
                                      • NOM
                                      • UL
                                      • GOST
                                        • Vibration resistance
                                        • 1 gn (f = 13-200 Hz) conforming to EN/IEC 60068-2-6
                                        • 1.5 mm peak to peak (f = 3-13 Hz) - drive unmounted on symmetrical DIN rail - conforming to EN/IEC 60068-2-6
                                          • Shock resistance
                                            15 gn conforming to EN/IEC 60068-2-27 for 11 ms
                                            Relative humidity
                                          • 5-95 % without condensation conforming to IEC 60068-2-3
                                          • 5-95 % without dripping water conforming to IEC 60068-2-3
                                            • Ambient air temperature for storage
                                              -25-70 °C
                                              Ambient air temperature for operation
                                            • -10-50 °C protective cover from the top of the drive removed
                                            • 50-60 °C with current derating 2.2 % per °C
                                              • Operating altitude
                                              • > 1000...2000 m with current derating 1 % per 100 m
                                              • <= 1000 m without derating
                                                • Unit Type of Package 1
                                                  PCE
                                                  Number of Units in Package 1
                                                  1
                                                  Package 1 Weight
                                                  1.753 kg
                                                  Package 1 Height
                                                  20 cm
                                                  Package 1 width
                                                  18 cm
                                                  Package 1 Length
                                                  20 cm
                                                  Unit Type of Package 2
                                                  S03
                                                  Number of Units in Package 2
                                                  2
                                                  Package 2 Weight
                                                  4.04 kg
                                                  Package 2 Height
                                                  30 cm
                                                  Package 2 width
                                                  30 cm
                                                  Package 2 Length
                                                  40 cm
                                                  Unit Type of Package 3
                                                  P06
                                                  Number of Units in Package 3
                                                  30
                                                  Package 3 Weight
                                                  65.95 kg
                                                  Package 3 Height
                                                  80 cm
                                                  Package 3 width
                                                  80 cm
                                                  Package 3 Length
                                                  60 cm
                                                  Sustainable offer status
                                                  Green Premium product
                                                  EU RoHS Directive
                                                  Pro-active compliance (Product out of EU RoHS legal scope)
                                                  Mercury free
                                                  Yes
                                                  RoHS exemption information
                                                  Yes
                                                  China RoHS Regulation
                                                  X
                                                  Environmental Disclosure
                                                  ENVPEP090202EN
                                                  Circularity Profile
                                                  ENVEOLI100205EN
                                                  WEEE
                                                  The product must be disposed on European Union markets following specific waste collection and never end up in rubbish bins
                                                  Warranty
                                                  18 months

                                                  Documents & downloads

                                                  hide show
                                                  Filter items
                                                  • All

                                                  • Product Brochures

                                                  • CAD Files and Packs

                                                  • Technical Data Catalogues

                                                  • Installation Instruction

                                                  • Product Environmental

                                                  • End of Life Manual

                                                  • Handout

                                                  • Data Bulletin

                                                  • Operating Manuals

                                                  • Certificates (MSDS)

                                                  • eTechPub

                                                  • DTM Files

                                                  Frequently Asked Questions

                                                  hide show

                                                  What is the replacement fan for an ATV16, ATV18, ATV28, ATV31, ATV11?

                                                  Issue:
                                                  Replacement fans for ATV16, ATV18, ATV28, ATV31, ATV11?
                                                   
                                                  Product Line:
                                                  ATV16 ATV18 ATV28 ATV31 ATV11
                                                   
                                                  Environment:
                                                  All
                                                   
                                                  Cause:
                                                  Replacement parts for obsolete drives.
                                                   
                                                  Resolution: 
                                                  Field replacement parts were never offered for these drives.  The only solution is to replace the drive.
                                                   

                                                  Do we have CAD drawings for the ATV312 drives?

                                                  Issue:
                                                  Do we have CAD drawings for the ATV312 drives?

                                                  Product Line:
                                                  Altivar ATV312 and ATV31

                                                  Environment:
                                                  All

                                                  Cause:
                                                  Cad drawings

                                                  Resolution:
                                                  Use the following link to the CAD Drawings Catalog.

                                                  https://www.schneider-electric.us/sites/us/en/support/product-support-resources/3d-cad.page


                                                  CTA-ID : 2061638

                                                  What is the din rail mounting kit part number for the ATV312?

                                                  Issue:
                                                  What is the din rail mounting kit part number for the ATV312?

                                                  Product Line:
                                                  ATV312

                                                  Environment:
                                                  All

                                                  Cause:
                                                  Desire to utilize din mounting kit option

                                                  Resolution:
                                                  The part numbers need to order the mounting kit for this drive are VW3A9804 and VW3A9805.

                                                  VW3A9804 covers the following range of drives: ATV312....
                                                  018M2, H037M2, H055M2, H075M2, H018M3, H037M3, H055M3, H075M3

                                                  VW3A9805 covers the following range of drives: ATV312....
                                                  HU11M2, HU15M2, HU11M3, HU15M3, HU22M3, H037N4, H055N4, H075N4, HU11N4, HU15N4, H075S6, HU15S6
                                                  Note: The din rail mounting kits are only available for the above drives. 

                                                  Note: Other drives not list above do not have a din rail kit.

                                                  What is a good source of information for the ATV12?

                                                  Issue:
                                                  What is a good source of information for the ATV12?

                                                  Product Line:
                                                  Altivar 12

                                                  Environment:
                                                  All models and serial numbers

                                                  Cause:
                                                  Information is needed for installation and programming.

                                                  Resolution:
                                                  User manual is document number BBV28581.  This manual includes instructions for installing the drive, connecting the control wiring, programming and troubleshooting.
                                                  https://www.schneider-electric.us/en/download/document/BBV28581/

                                                  Can the ATV312 be powered by an external 24V only?

                                                  Issue:
                                                  Powering the ATV312 by an external 24Vdc only

                                                  Product Line:
                                                   Altivar 312

                                                  Environment:
                                                  All

                                                  Cause:
                                                  Installation/programming
                                                   
                                                  Resolution:
                                                  No, this drive must have line voltage applied.  The voltage must be within -15% to +10% of the rated line voltage. 

                                                   

                                                  What input is designed for a bipolar -10v to +10v input on the ATV32 drives?

                                                  Issue:
                                                  What input is designed for a bipolar -10v to +10v input on the ATV32 drives?

                                                  Product Line:
                                                  Altivar ATV32

                                                  Environment:
                                                  All

                                                  Cause:
                                                  AI2 is default for -10v to +10v input.

                                                  Resolution:
                                                  IO menu AI2 set up

                                                   Bipolar analog input 0 ± 10 V (maximum voltage ± 30 V)

                                                  The + or - polarity of the voltage on AI2 affects the direction of the set point and therefore the direction of operation.

                                                  • Impedance 30 kÙ
                                                  • Resolution: 10 bits
                                                  • Precision ±0.5% in 50/60 Hz for 25 °C, ±0.2% in 50/60 Hz for –10 to +60 °C at Äè = 60°C,
                                                  • Linearity ± 0.2% (max. ± 0.5%), of max. value
                                                  • Sampling time 2 ms

                                                  When do the cooling fans on the ATV212 drives come on?

                                                  Issue:
                                                  Wondering when the cooling fans on the ATV212 drives come on?

                                                  Product Line:
                                                  Altivar 212

                                                  Environment:
                                                  All

                                                  Cause:
                                                  Fan control strategy

                                                  Resolution:
                                                  The fan starts when the drive is in RUN state.
                                                  The fan stops after the STOP command (with a time delay in relation to the thermal state).

                                                  Is there a problem using Altivar 61 or Altivar 71 drives delta power system?

                                                  Issue:
                                                  Wants to use Altivar 61 or Altivar 71 drives on delta power system.

                                                  Product Line:
                                                  Altivar ATV61 and ATV71

                                                  Environment:
                                                  All

                                                  Cause:
                                                  Needs to know if the RFI filter needs to be disabled when using a corner grounded delta system?

                                                  Resolution:
                                                  As long as the input voltage remains within the normal range there should not be a problem.
                                                  This should be treated the same way as an impedance grounded system.
                                                  Remove the jumper to the left of the power terminal.
                                                  See the section of the installation manual for Operation on an IT (Isolated or impedance grounded neutral) system for details.
                                                  See the drives installation manual for more information and location of the RFI's filter tab.

                                                  The figure 1 example below is for the low horsepower ATV61 and ATV71 drives.


                                                                                                     Figure 1.

                                                   

                                                  What should be checked if an Altivar 61 or 71 display is showing NLP?

                                                  Issue:
                                                  Wondering what should be checked if an Altivar 61 or 71 display is showing NLP?

                                                  Product Line:
                                                  ATV61/71 drives

                                                  Environment:
                                                  All

                                                  Cause:
                                                  Drive displays 'NLP'

                                                  Resolution:
                                                  NLP indicates that no line power is present on the L1, L2 & L3 input terminals of the drive controller.

                                                  Check voltage at the L1, L2 & L3 terminals.
                                                  Check for open circuits on line contactors, circuit breakers, disconnect switches, or fuses.

                                                  If NLP state does not change with correct voltage present on L1, L2, & L3, remove the control board and check for loose connections of ribbon cables inside the drive.
                                                  WARNING: This step should be performed while the drive is powered down, and proper personal protective equipment should be worn. 

                                                  For example: In an ATV71HC25N4 a customer found a loose X3 connector from the control board to the board behind and above the control board. This connector was on a ribbon cable that was about 1 inch by 1 inch. Drive ran OK after this was reseated.

                                                  Can the analog output of the ATV61 or ATV71 be set up as 0-10 VDC instead of 4-20 mA?

                                                  Issue:
                                                  Needs to set up a analog output of the ATV61 or ATV71 drive, to be set up as 0-10 VDC instead of 4-20 mA.

                                                  Product Line:
                                                  ATV61 and ATV71

                                                  Environment:
                                                  All

                                                  Cause:
                                                  NA

                                                  Resolution:
                                                  Yes.
                                                  Go to the Input/Output menu (1.5) and set AO1 type to voltage (0-10v range). Set AO1 assignment to the proper setting. The minimum and maxim range can also be adjusted inside the 0-10 V or 4-20  mA ranges.


                                                   

                                                  Is there an offer for Nema 4X rated drives?

                                                  Issue:
                                                  Wondering if the ATV61 or ATV71 drives are available in type 4 or 4X enclosures?

                                                  Product Line:
                                                  Altivar ATV61 and ATV71 open type drives

                                                  Environment:
                                                  All

                                                  Cause:
                                                  Needs to get the ATV61 and ATV71 drive in a NEMA 4 or 4X stand alone enclosure.

                                                  Resolution:
                                                  There is not a standard offering for type 4 or 4X enclosures for our drives.
                                                  It may be possible to install the drive in a properly selected enclosure by a local panel builder or contractor.
                                                  Or, contact a local SquareD field office for assistance. They may be able to offer assistance with other options.

                                                  Why is the keypad not included with ATV61 and ATV71 drives?

                                                  Issue:
                                                  The keypad is not included with ATV61 and ATV71 drives.

                                                  Product Line:
                                                  Altivar 61 and 71 drives

                                                  Environment:
                                                  All

                                                  Cause:
                                                  Customer concerned whether the HMI came with the drive

                                                  Resolution:
                                                  For all ATV61 and ATV71 drives without the letter Z at the end of the part number the keypad is included.
                                                  However, it is easy to not notice the keypad in the packaging material. The keypad is located inside folded cardboard that also functions as packing material. Check inside all folded cardboard packing materials. There is no sticker to indicate that the keypad is inside.

                                                  ATV61 & ATV71 drives with the letter Z at the end of the part number do not include the removable LCD HMI keypad display. These units do have a simplified LED display and programming keys on the face of the control board itself. The removable LCD HMI keypad display may be installed on these units.


                                                   
                                                  Show More