MASTER YOUR CASTLE with your new build or reno project
Enter competition
Image of 751 Indoor Infrascan 2 Wire 2A

751

Passive Infrared Sensor, 2 Wire, 2A

Image of 751 Indoor Infrascan 2 Wire 2A
Colour: White Electric
Colour: Per UOM Std.
  • White Electric 1 PCE
Added to cart
Successfully added, you can view your cart here

Key Features & Specifications

hide show
  • Maximum load current: 2A
  • Minimum load: 40W
  • Maximum off-state leakage current: 5mA
  • Conductors Required: 2 Wire
Range of product
Infrascan
Range
Infrascan
Product brand
Clipsal
Product or component type
movement sensor
[Ue] rated operational voltage
200...265 V
Mounting support
  • ceiling
  • wall
    • Mounting height
      2.4 m
      Ambient air temperature for operation
      0-40 °C
      REACh Regulation
      Reference contains Substances of Very High Concern above the threshold
      EU RoHS Directive
      Pro-active compliance (Product out of EU RoHS legal scope)
      Toxic heavy metal free
      Yes
      Mercury free
      Yes
      RoHS exemption information
      Yes
      China RoHS Regulation
       Pro-active China RoHS declaration (out of China RoHS legal scope)
      Circularity Profile
      ENVEOLI121002EN

      Frequently Asked Questions

      hide show

      Which 751 infrascan , can use 2 units to control the same load??

      751R-WE

      Can a 751 be used with 25W LED?

      Yes, it can but you will need to put a 31CAP in parallel with the load.

       

      Why wont my 751 passive infrared sensor work, it has a 20W flood light wired to it?

      The reason why the light/ sensor wont operate as deisred is because the minimum operating load is 40W. Due to the design of this sensor it is only capable of a maximum of 2 Amps and a minimum of 40W. It also has a maximum off-state leakage current of 5mA.
      If any of these values are exceeded this may casue the system not to work.

      For further information please visit https://www.clipsal.com/Trade/Products/ProductDetail?catno=751
       

      Is there a recessed wall mount sensor?

      No unfortunately we do not offer a recessed sensor. However we can offer a Surface mount sensor, part number 751R.
      Some of the key features are:
      • 10A maximum load current
      • Stand-by power consumption is less than 1W
      • 3 Wire
      • Neutral required
      • 30 seconds warmup time
      • 6m x 6m, 8.5m from sensor head, head rotatable through 120° rated detection field at maximum sensitivity
      • 5 seconds to 20 minutes timer delay range
      • Cables accommodates 3 terminals, up to 1 x 2.5mm² cable per terminal
      • Length of sensor 57mm
      • 100mm Diameter

      For furthur information please visit www.clipsal.com/Trade/Products/ProductDetail?catno=751R

      OR 

      See the attached installation instructions.

      Why are my lights flickering on a 751 sensor?

      Generally it is because 1 of 2 reasons, Incompatible load type or your not exceeding your minimum load.
      Please see table below for specifications:
       
      Catalogue Number 751 751R
      Minimum Loads 40W 0W
      Compatible Load types Incandescent Incandescent
        240V Halogen 240V Halogen
        Iron Core Transformers* Iron Core Transformers
          Fluorescent
          Electronic Transformers
           
      Incompatible Loads Fluorescent N/A
        Electronic Transformers N/A
        Small Motor Loads 5A Max N/A
        Dischharge Lamps N/A

      For further information please visit Trade - Clipsal by Schneider Electric