Quantcast

4 Gang Vertical General Power Outlet

White | 4 Gang Vertical General Power Outlet

4 Gang Vertical General Power Outlet

Item Number: 641-WH

Retail
$155.05
RRP (Inc. GST)

Datasheet

Barcode

Qty UoM EAN Colour
-
-
-

Specifications

Design

Range of product

PDL 600 Designer Series

Product brand

Clipsal

Colour code

RAL 9010

Physical

Control type

ON/OFF button

Number of gangs

4 gangs

Pin number

3

Number of power socket outlets

4

Actuator

  • switch
  • rocker
    • Mounting position

      vertical

      Fixing mode

      by screws

      Local signalling

      without light indicator

      [Ue] rated operational voltage

      230...240 V AC

      [In] rated current

      10 A

      Width

      81 mm

      Height

      194 mm

      Fixing center

      84 mm

      Standards

    • AS 3100
    • AS 3133
    • AS 3112
      • Material

        Material

        plastic

        Others

        Package 1 Weight

        1 kg
        Show all specifications

        Frequently Asked Questions

        hide show

        What does NST mean on Altivar drives?

        Issue: 
        NST on Altivar drives.

        Product Line:
        All Altivar drives

        Environment:
        All

        Cause:
        NST is not a fault but rather a status indicating the drive is in a freewheel stop condition.

        Resolution:
        NST is a very general status on drives.  It is not a fault condition.

        See below for a number of reasons why NST is present depending on application/setup.
        Causes and fixes :
         
        The drive is in 2 wire control (TCC = 2C) and was powered up with an active run command.
        Cycle the run command or set TCT to LEL. (IO menu, 2 wire type = level)
        https://www.se.com/ww/en/faqs/FA238669/

        The drive has an input assigned to Freewheel stop, NST.
        The input needs to be active.
        https://www.se.com/ww/en/faqs/FA170907/

        The drive is in 3 wire control (TCC =3C).
        LI1 must be active before the NST will clear.
        https://www.se.com/us/en/faqs/FA274804/

        The drive is being controlled by serial communication, and drive is not receiving the proper command signal.
        The drive will display NST until the correct value has been written to the command word.
        https://www.se.com/ww/en/faqs/FA314997/

        A loss of a 4-20mA signal is programmed to freewheel stop.
        When the input is lost, status goes to NST. Verify the 4-20 mA signal.

        The drive is in terminal control, and the STOP button on the integral or remote keypad was pressed.
        While in terminal control, the STOP button functions as an E-STOP.  If the keypad STOP button is pressed, the drive will go to NST (excluding the ATV212, which will display a flashing "E"). Power cycle the drive to clear the NST.
        https://www.se.com/us/en/faqs/FA164112/

        For the ATV61/71 VFD only: If the drive is running, and the voltage applied to the PWR input terminal drops below +19Vdc, the drive will stop and display NST.
        You will need to make sure you close the +24 VDC to PWR input and cycle off and on the run command again. Make sure the factory-installed jumper between +24 and PWR is connected firmly. Or if a safety circuit is connected to these terminals, be sure the circuit is closed.  

        Automatically restarting alarm redirection in ClearSCADA

        Sometimes there is a need to restart alarm redirection sequence if a particular alarm does not get acknowledged or cleared in specified time. Consider an example where a redirection action is configured to send an e-mail once a point goes into alarm. If the alarm does not get cleared within 30 minutes, another e-mail needs to be sent out. The e-mails should be sent out repeatedly every 30 minutes until the alarm is cleared.

        This can be achieved by using the RestartRedirections() method. Below is a quick run through on how this method could be used.

        1. Consider an analog point named Pressure with an alarm redirection action configured to send an e-mail whenever the point is in alarm.

        2. Locate this E-Mail Action in Database Explorer and assign this action to a particular redirection group for which alarm redirection needs to be restarted. If no redirection groups have been configured yet, type in an arbitrary name to create a redirection group.

        3.Create new Method Action and specify Method Object. In this case, Method Object is going to be the object for which alarm redirection needs to be restarted. Select Restart Redirections as Method. Enter the redirection group's name in single quotes ('Redirection Group Name') as the value for the Redirection Group argument.

        4. Add the newly created method action to the list of redirection actions in point's properties. Make sure to specify a delay to restart alarm redirection.

        Only redirection actions configured under the same redirection group (PressureGroup in this case) will be restarted. Do not assign other redirection actions to the same redirection group if they do not need to be triggered repeatedly. Make sure the method action is also assiging the same redirection group (PressureGroup in this case) to be triggered again.

        What is the part number for a mounting bracket for the M8080H2?

        The part number for a mounting bracket for the M8080H2 is - 800FB2H

        For further information , visit link below:-
        https://www.clipsal.com/Trade/search-results?q=800FB2H
        User-added image

        What is the depth of PDL 644 mounting blocks, 640RC and 640SC

         It is 19mm deep

        How do I wire the BMXDDO1602 discrete IO 24 VDC module for a M340 PLC?

        BMXDDO1602 wiring the 24 VDC module as per the diagram:
         

        What grade of stainless steel are the screws used in 56 series products?

        The Anti-Corrosion Enclosure Screws are Stainless Steel Grade 316 for all 56 series products.

        56MS Self Drilling Screw:
        https://www.clipsal.com/Trade/Products/ProductDetail?CatNo=56MS&c=6&ms=8&s=36&mg=12064&g=120641307&sg=120641407

        For further information or support please call the Clipsal Technical Support on 1300 20 25 25


         
        Show More