The 60TDM is now available after going under a redesign. We also have the 60TDSM which is the slave dimmer mechanism which would be suiatble for 2-3 way dimming applications.
Yes, the jumper needs to be removed from the 60TDM, for 2 and 3-Way switching situations.
Yes, can be used in the same please as far as they are using one touch grid plate.
Part no 60tdm can be used as per wiring diagram for 2 way switching
It is 2 Way if you use it with a 60TSSM
Unfortunately, it only suits Saturn 1 touch series, not Saturn 4000.
The part number 60TDSM can only be used in One Touch.
Unfortunately, Part number 60TDSM can only be used in One Touch.
No, the 60TDM can only be used on dimable loads as it has a soft start feature as well a dimming functionality.
Some of the key features are:
- Touch sensitive control interface
- Cool blue LED Halo indicator
- Audible alert tone feedback
- Capable of up to 3 way dimming/switching
- Dimming compatibility assurance with Clipsal LEDs (refer to clipsal.com/load)
For further information please visit www.clipsal.com/Trade/Products/ProductDetail?catno=60TDM
The 60TDM is a touch mechanism and is suited to the OneTouch series wherefore the 4061E2PUDM is a push button mechanism suited to the Saturn series.
Please note these mechanisms are NOT interchangeable between series.
Add 1 or 2 x 60TDSM (secondary module) and remove the jumper pin from the centre of the 60TDM.
The OneTouch switches can be wired in the same way, by adding a secondary module (60TSSM) or 2 and removing the jumper from the 60TSM.
Note: the load is always supplied from the Primary module.
The switch code has changed to 60TSRM3 this switch now has a relay in the back of the switch and can switch all types of loads
60TSRM3 switch 6AX 3 wire needs a neutral
60TDM dimmer module 350W max
60TDSM this is the slave switch to allow two way and 3 way switching and dimming
Part codes 4063TC + 3 x 60TDM
Saturn One touch is now obsolete.
The part codes are 4061TC (OM - Ocean Mist and PW - Pure White) this is just the plate 4062TC-xx, 4063TC-xx 4064TC-xx 4066TC-xx are the other plates.
The Onetouch switch is 60TSRM3, which is 6AX 3 wire and requires a neutral connection.
The Onetouch dimmer module code is 60TDM, 350W max, does not require neutral connection.
The dimmer/switch secondary mech is 60TDSM. This can act as a slave for either the 60TSRM3 or 60TDM to allow 2 and 3 way switching and dimming. Does not require neutral connection.
See wiring diagram for typical dimmer and switch application
Yes, the operation of this light consists of short press "On", short press "Off", long press " Ramp down" long press "Ramp up".
You need to use part codes 4062TC + 2 x 60TSM
Unfortunately no. Saturn OneTouch mechanisms have to be ordered separately.
Saturn onetouch mechanisms to suit the plates are:
60TSRM3 - Saturn OneTouch master electronic switch, 3-wire, 6AX, integral relay
60TDM - Saturn OneTouch master dimmer, 2-wire, 350 W max, suitable for Clipsal LEDs
60TDSM - Saturn OneTouch remote dimmer/switch, supports up to three-way dimming and switching
For further information, please visit: https://updates.clipsal.com/ClipsalOnline/Files/Brochures/A0000293.pdf
No. Unfortunatelythe part number is only available in 2 wire.
Part number 60TDSM can only be used in One Touch.
Only in saturn one touch clipsal push button dimmers part code 60TDM
The part number for one touch dimmer mech is 60TDM
60TSM is replaced by 60TSRM3, OneTouch Switch Mech, is 3-Wire, 6AX, 220-240V AC
- Touch sensitive control interface
- Cool Blue LED Halo indicator
- Audible alert tone
- Reliable Control of many different load types within the home
- Capable of up to 3 way switching
For further information, please visit https://www.clipsal.com/Trade/Products/ProductDetail?catno=60TSRM3
The Configuration Chart for the Saturn OneTouch range is:
4061TC (1 Gang Grid and Cover Only)
4062TC (2 Gang Grid and Cover Only)
4063TC (3 Gang Grid and Cover Only)
4064TC (4 Gang Grid and Cover Only)
4066TC (6 Gang Grid and Cover Only)
4061ATC (1 Gang Architrave Grid and Cover Only)
4062ATC (2 Gang Architrave Grid and Cover Only)
All of the above Cover plates can be configured to be Switches or Dimmers to your requirements by ordering the Grid & Cover plate and
then the matching OneTouch Dimmer or Switch. 60TSM (OneTouch switch 400W) or 60TDM (OneTouch Dimmer 350W)
No unfortunately this is a one-way device and cannot be two-wayed as it is integrally switched. If you wish to two-way dim a circuit you will need to use a master and slave mechanism in the OneTouch Series. To create such a setup you would require a 2X 4061TC, 60TDM and a 60TDSM.
The part number for Saturn One Touch 2 way dimmer is:- 60TDM with 60TDSM
For further information , please visit the links below:-
The codes are
60TSRM3 Saturn OneTouch master electronic switch, 3-wire, 6AX, integral relay
60TDM Saturn OneTouch master dimmer, 2-wire, 350 W max, suitable for Clipsal LEDs
60TDSM Saturn OneTouch remote dimmer/switch, supports up to three-way dimming and switching Wall plates —
Available in colours EB, OM, PW
4061TC 1 gang grid and cover plate, Saturn OneTouch — standard size
4062TC 2 gang grid and cover plate, Saturn OneTouch — standard size
4063TC 3 gang grid and cover plate, Saturn OneTouch — standard size
4064TC 4 gang grid and cover plate, Saturn OneTouch — standard size
4065TC 5 gang grid and cover plate, Saturn OneTouch — standard size
4066TC 6 gang grid and cover plate, Saturn OneTouch — standard size
4061ATC 1 gang grid and cover plate, Saturn OneTouch — architrave size
4062ATC 2 gang grid and cover plate, Saturn OneTouch — architrave size
4062TFC 2 gang grid and cover plate, Saturn OneTouch, suits fan control switch 4060CSFM and Saturn OneTouch mechanisms
Yes it can be used on split phase fans
No, it only comes with White and Black covers.
The 600SM protects all other devices on the circuit but it can only handle a limited number of surges.
For more information see attched installation sheet.
The keys for part number 30TKM are only available as a special.
We don’t do them as a standard part.
Replacement part numbers PDL 648TM + PDL 600RM
Use PDL 100MPIR + PDL 600RM relay
Yes, it is a PDL 600RM with a 16A resistive rating
No use a industrial relay or contactor
6AX = 6amp reactive load, or 16A resistive loads.
Not available, you can use the Clipsal 30TKM this can be fitted in a single VH plate (C2031VH)
Use a PDL 600SM with a 600 series socket with an extra switch
When you purchase a 600SM it comes with a White and Black cover and you can put on either one.