White | 32A Socket Range

TSXDSY08T31 wiring the 48 VDC protected transistor output module as per the diagram:

The part number is LV438576.
 

Issue

Unable to connect to a Network Management Card or Network Management Card enabled device via a serial connection.


Product Line


• Web/SNMP Card - AP9606
Devices with an embedded Web/SNMP Card include (but are not limited to): Environmental Monitoring Unit 1 (AP9312TH)

• Network Management Card 1 (NMC1) - AP9617, AP9618, AP9619
Devices with an embedded Network Management Card 1 include (but are not limited to): Metered/Switched Rack PDUs (AP78XX, AP79XX), Rack Automatic Transfer Switches (AP77XX, Environmental Monitoring Units (AP9320, AP9340, Netbotz 200)

 
• Network Management Card 2 (NMC2) - AP9630/AP9631CH, AP9631/AP9631CH, AP9635/AP9635CH
Devices with an embedded Network Management Card 2 include (but are not limited to): 2G Metered/Switched Rack PDUs (AP84XX, AP86XX, AP88XX, AP89XX), Rack Automatic Transfer Switches (AP44XX), Certain Audio/Video Network Management Enabled products, Smart-UPS Online (SRT).

Environment

• All firmware versions
• All serial numbers


Cause

Several issues can cause a problem with a terminal session over a serial connection. See below for some troubleshooting tips.


Resolution

1. Check the physicals – Ensure you are using the correct cable. There are several different communication cables APC manufactures. Check your unit’s user manual for the correct part number, which should also be printed on the cable itself. If you have another cable, try it. You can also confirm the cable works if you have another unit to try it in.

2. Ensure you are using the correct COM port - Some servers have many com ports. Ensure you are using the communication port mapped to the serial port.

3. Ensure you are connecting at the correct settings - APC units can communicate at 2400, 9600, 19200, 38400, and 57600 bps. Please reference the product’s user manual for the default settings. You can also try connecting at each rate. Please keep in mind that the baud rate CAN BE CHANGED by the user, a change to the configuration file, or a managing device like ISX Manager or StruxureWare Central.
   
   APC units can be forced to a baud rate at the username and password prompt. If you are having an issue connecting, try setting the baud rate to a different value:
   
   Username: <username>
   Password: <password><space>-<baud rate>
   
   This example will set the baud rate to 2400 bps, using the default username and password:
   
   Username: apc
   Password: apc -2400
   
   The unit will inform you of the baud rate change. If it does NOT, you might have the incorrect username and password. In which case, reference knowledgebase number FA156075.
    
4. If applicable, check to ensure your USB to Serial Adapter is working properly - Many of these devices require a driver to work properly. Check to make sure this device is recognized correctly by your operating system.

The Closest alternative PM1200 is METSEPM2230
See link below for more details:
https://www.se.com/au/en/product/METSEPM2230/easylogic-pm2230%2C-power-%26-energy-meter%2C-up-to-the-31st-harmonic%2C-lcd-display%2C-rs485%2C-class-0.5s/

Product Line:
Circuit Breakers
PowerPact P

Environment:
Electrical Distribution Equipment

Resolution:
Neutral CT`s are as follows:
S33575 250A
S33576 400 to 1600A


 

Product Line:
NT and NW Masterpact breaker

Resolution:
 
 Table 41:        T-Frame Circuit Breakers
External neutral sensor for 3-phase, 4-wire residual ground fault system (or for neutral current monitoring).
These neutral sensors include their wiring harness. To order this harness as a spare part, order cat. no. NCTWIRING. 
 

NT Circuit Breaker Sensor Plug

External Neutral Sensor for general use

External Neutral Sensor Square D Panelboard

External Neutral Sensor for use in Square D Switchboards

  External neutral sensor for circuit breakers with standard neutral protection

100–250 A	S33575	S33924	S33926
400–1600 A	S33576	S33925	S33927

  External neutral sensor for circuit breakers with oversized neutral protection♦

100 A	S33575	S33924	S33926
250 A	N/A	N/A	N/A
400–1000 A	S33576	S33925	S33927
1200/1250 A	S48896	N/A	NA
1600 A	S48182	N/A	NA

♦Oversized neutral protection = 1.6xIr where Ir = long time pick-up.


Table 42:        W/Y-Frame Circuit Breakers
External neutral sensor for 3-phase, 4-wire residual ground fault system (or for neutral current monitoring) and external sensor for Modified Differential Ground Fault (MDGF) or Source Ground Return (SGR) system.
These neutral sensors include their wiring harness. To order this harness as a spare part, order cat. no. NCTWIRING.
 

Frame Size	Sensor Plug (A)	External Neutral Sensor		PZ4 External Neutral Sensor (For use in PZ4 Switchgear)		MDGF/ SGR Sensor►
		For Residual Ground Fault	For 3-Pole Circuit Breaker with Oversize Neutral Protection♦	For Residual Ground Fault	For 3-Pole Circuit Breaker with Oversize Neutral Protection♦
W	100	S48916	S48916	S48902	S48902
	250		N/A		N/A
	400	S34036	S34036	S48903	S48903	S33579
	600/630
	800
	1000
	1200/1250		S48896
	1600		S48182		N/A
	2000	S48896
	2500	S48182		S48182
	3000		N/A
	3200
	4000					N/A
Y	2000	S48897•	S48897•	S48898•	S48898•	S33579
	2500
	3000				N/A
	3200
	4000
	5000		N/A	S48897•
	6000
	6300			N/A

•Kit includes qty. (2) neutral sensors.
►Four MDGF sensors (phase + 1 neutral) are required for W-frame; eight MDGF sensors are required for Y-frame. For SGR system, only one sensor (neutral) is required for W-frame; two sensors for Y-Frame.
        An MDGF/SGR ground fault interface module (Cat. no. S48891) is also required for each circuit breaker. 
♦Oversized neutral protection = 1.6xIr where Ir = long time pick-up.

See catalog 0613DB1607 for more Masterpact parts