YES - 30BCRM OR 30BCBM OR both in a 4031 or 4032 Communication plate.
The PDL 680M32 (switch module, 1 way, 2 terminal, 32A, 240V) is only available in white or black.
The plug that suits the 402/32 outlet is the 492/32.
No , The 60R32 series mechs are only designed to go into the 4025XA and 4025XUA plate styles. If Mechs over 32 amp are required for Saturn plates then you will need either 4031VH plate and 30M35 series mechs or the dedicated cooker plates 4061D32 or 4061/45 series
The Saturn Zen 2 gang plate accommoddates 30m35 mech is Z4032VH.
No. Unfortunately, part number 30M35 CANNOT be used in 2031V66.
No - It is just a 2 pole switch
But a 30MD2 is a 2p 2way (6 terminals)
What is the fuse or circuit breaker rating for LXM32 drives?
For 115VAC and 230VAC drives, the maximum fuse to be connected upstream is 25 Amps, Class CC or J as per UL 248-4, alternatively circuit breakers with B or C characteristic.
For 400VAC and 480VAC drives, the maximum fuse to be connected upstream is 30/32 Amps, Class CC or J as per UL 248-4, alternatively circuit breakers with B or C characteristic.
Schneider Electric 3-wire serial cable p/n TBUM297801 is used to connect from an 3-pin based RS-232 port on the SCADAPack 4000 series Transmitter (4012, 4032, 4102, 4203DR, 4203DS) to DE-9P connector on a DTE such as a PC.
The 30M35 does not come in dark grey.
However it does come in Chrome Shadow or Soft Grey.
For further information please visit https://www.clipsal.com/Trade
Yes, the 60R32 series are designed only to be fitted into the 4025XUA and 4025XA series
The 60R32 switch mechanism accommodates up to 4 x 1.5mm2 or 3 x 2.5mm2 or a single 4mm or a single 6mm.
The neutral link big enough for 70mm2 cables would be the BP350/7.
Some of the key features are:
- Black base and cover
- Two screw per take off tunnel
- Incoming cables clamped with single grub screw
- 2 tunnels: 15.0 mm Diameter accommodate 120 sq mm cables
- 2 tunnels: 9.5 mm Diameter accommodate 50 sq mm cables
- 2 tunnels: 8.0 mm Diameter accommodate 35 sq mm cables
- 1 tunnel: 5.5 mm Diameter accommodates 16 sq mm cables
- Terminal bar: 25.4 x 19 x 95.3 mm
For further information please visit https://www.clipsal.com/Trade/Products/ProductDetail?catno=BP350/7
Socket to suit is 402 series
Yes - as its rated at 15A 4 x 2.5mm cables will fit
You will need to use the 4032VH plates and any Clipsal 30 Series data and AV mechs,
these plates will aslo fit any 30 series switch mech,
EG 30TV75M, 30PFM, 30HDMIA, VDIB17756U-we
No the largest can accommodate up to 50mm2 and the part number is a 650/4/35-BK.
No. We have 30M35 which is 1 pole, 35A mech.
Read LXM32 actual torque in SoMachine
LXM32M, LXM32A, LXM32C
The easiest way to read the actual torque on a LXM32 drive is to use the function block MC_ReadActualTorque_LXM (See attached screenshot)
Looking for the CN10 connector for the LXM32 drive
The CN10 connector on the LXM32 drive cannot be sold alone.
It comes in a complete connectors kit, part# VW3M2202. This kit is included in the box when buying a LXM32 drive and can be ordered separately.
No there is no saturn mech available. There is either the Z4061/45 cooker switch plate or the 30M35 in a Z4031VH Plate
The part number is 30M35-3S, but not anymore available for sale in New-Zealand.
The part number 30M35 mech will go into 4031VH plate.
Save or restore the LXM32 parameters using a SIM card
LXM32 servo drives
Please see attached document.
Procedure to autotune a LXM32 drive through SoMove
The attached manual shows how to autotune a LXM32 drive through the SoMove software.
Getting E7701 on the LXM32 drive
E7701 is a system error: Timeout during connection to power stage.
The drive will have to be replaced. This error cannot be reset.
Yes, 60R32 or 60R32COOK - 32A , mech. Do not have a double pole version.
What is the recommended spacing for 22mm pushbuttons ?
Horizontal spacing is 1.18`` or 30mm, vertical spacing is 1.57`` or 40mm, hole size 0.88`` ( recommended 0.89`` ) or 22.5mm
This size will vary depending upon the rating of the conductors:
Legacy KB System (APS) Data: RESL212274 V1.0, Originally authored by DaFr on 08/09/2013, Last Edited by DaFr on 08/09/2013
Related ranges: Others protection relays
A floating point value can be moved into 4XXXX registers with the equation network. An example of moving a floating point value of 123.456 into registers 40001 and 40002 is shown below:
Undervoltage limit for the LXM32 drive?
The undervoltage limit varies depending on the servo drive's part number.
The attachment shows the different limits.
Goals and Symptoms
Getting error E7701 on LXM32 and unable to reset
E7701:System error: Timeout during connection to power stage.
You can try to update the firmware if you have an older revision.
This is an error in the power stage so most of the time, you need to send the LXM32 back for replacement
What is error A320 on a LXM32 drive?
A320 is a following error. The parameter is _SigLatched Bit 8
Reason could be a high external load or an acceleration that is too high.
Solution is to reduce external load or acceleration or use a differently rated drive.
Error response can be adjusted via parameter ErrorResp_p_dif
Auto enable the LXM32 drive using SoMove
Instead of having to activate an input in order to enable the LXM32 drive, you can set the following parameters to automatically enable the drive on power-up:
In SoMove (See attached):
Axis Configuration > IO_AutoEnaConfig = ON
Axis Configuration > IO_AutoEnable = AutoOn
Can I connect and change parameters on LXM32 servo drive using SoMachine?
In SoMachine, when you add a LXM32 drive to the network, you can double click it and go to the 'Configuration of the device' tab, where you can see a SoMove-like screen (See attached).
Just like the SoMove interface, you can connect to the drive and upload/download/edit parameters.