Quantcast

General Accessories Nuts, No.6 Nc Square Nut

General Accessories Nuts, No.6 Nc Square Nut

General Accessories Nuts, No.6 Nc Square Nut

Item Number: 359

Datasheet

Barcode

Qty UoM EAN Colour
-
-
-

Specifications

Design

Product brand

Clipsal

Physical

EU RoHS Directive

Compliant

Mercury free

Yes

RoHS exemption information

Yes

China RoHS Regulation

Product out of China RoHS scope. Substance declaration for your information

Environmental Disclosure

ENVPEP060307EN

Others

Package 1 Bare Product Quantity

1

Unit Type of Package 1

PCE

Number of Units in Package 1

1

Package 1 Height

3 cm

Package 1 Width

10 cm

Package 1 Length

8 cm

Package 1 Weight

102 g

Unit Type of Package 2

BAG

Number of Units in Package 2

100

Package 2 Height

0.5 cm

Package 2 Width

9.5 cm

Package 2 Length

13 cm

Package 2 Weight

10.2 kg

Unit Type of Package 3

BB1

Number of Units in Package 3

500

Package 3 Height

7 cm

Package 3 Width

8.8 cm

Package 3 Length

10.8 cm

Package 3 Weight

51 kg
Show all specifications

Frequently Asked Questions

hide show

MSDS material safety data sheet for S33593 battery

Issue:
Documentation

Product Line:
Catalog Number S33593

Resolution:
The attached file is the MSDS for the S33593 battery.

Why is my 5080CTC Touch Screen not booting up correctly/fully?

In regards to the 5000CTC touch screen stuck in booting mode.

It's a known issue if you are touching the screen during the boot up process the CTC will fail to boot entirely and will appear to be stuck in the booting up mode.

Our advise is once the screen is powered ON or soft reset, is to not touch the screen until it's fully booted and connected to C-Bus indicated in the top left corner.


5080CTC/5080CTCV2/5080CTCV3

Testing a Masterpact breaker, and the FFTK test kit says the breaker is different from what it is and it will not allow it to be changed

Issue:
Testing a Masterpact breaker, and the FFTK test kit says the breaker is different from what it is and it will not allow it to be changed.

Product Line:
Masterpact NT NW
Full Function Test Kit (FFTK) S33595

Resolution:
To change it, go into the trip unit menu by pressing the wrench key. Then go to Micrologic Setup, Breaker Selection, and change the Standard to Not Def. Press Meter key to exit, save settings, and continue to set up test on FFTK manually.

Issue: With Micrologic P/H trip units with firmware 2009AJ, date code 0948 or later, testing with the FFTK may have an issue if the trip unit has been set up for “ANSI” or “IEC/GB” as the standard and a breaker selection has been made. This issue can be corrected by choosing “not def” in the Breaker Selection menu. Once “not def” is saved, then the testing with the FFTK may begin with the user inputting the breaker type, standard, and interrupt rating on the FFTK touch screen.

When the testing is done, you can setup the breaker selection in the trip unit as they were prior to testing.

Please see attached document which contains photos of how to make the setup changes on the trip unit.

What are the catalog numbers and available voltages for shunt trip and shunt close accessories for the Masterpact NW?

Product Line:
Circuit Breakers

Resolution:
Shunt Trip, Second Shunt Trip, and Shunt Close
Voltage 50/60 HzT-, W-, & Y-Frame
Fixed
T-Frame
Drawout
W- & Y-Frame
Drawout
12 dcS47359S33809S48490
24–30 ac/dcS47360S33810S48491
48–60 ac/dcS47361S33811S48492
100–130 ac/dcS47362S33812S48493
200–240 ac/dcS47363S33813S48494
277 acS47364S33814S48495
380–480 acS47365S33815S48496

See instruction bulletin, 48049-237-03

For VA consumption

Is it possible to defeat or disable ground fault on Masterpact NW with Micrologic 6.0A trip units for primary injection testing?

Issue:  
Is there a way to defeat or disable ground fault on a Masterpact NW breaker for primary injection testing?  

Product line:  
Power circuit breakers

Resolution:  
There are two ways to defeat ground fault on the NW breaker for primary injection testing.  You can use the hand held test kit, S33594, or the full function test kit, S33595. Or you can use the looping method to counter the single phase current during primary injection testing. See the attached data bulletin 0600DB9901, page 35, for the looping method, or FAQ Looping Method for Testing Breakers with Ground Fault Trip Units
 

What is the operating voltage tolerance, catalog numbers, and clearing times for the Masterpact NT and NW shunt trip and shunt close coils?

Issue:  
What is the operating voltage tolerance, catalog numbers, and clearing times for the Masterpact NT and NW shunt trip and shunt close coils?

Product Line:
Masterpact NT NW

Resolution:
Shunt trip: operating threshold is 0.7x to 1.1x Vn (nominal voltage)
Shunt close: operating threshold is 0.85x to 1.1x Vn
Catalog numbers are the same for MX and MN (shunt trip and shunt close) devices; function is determined by placement in the breaker.
 
Voltage (V) at 50/60 HzT-, W-, & Y-Frame FixedT-Frame DrawoutW- & Y-Frame Drawout
12 DCS47359S33809S48490
24-30 AC/DCS47360S33810S48491
48-60 AC/DCS47361S33811S48492
100-130 AC/DCS47362S33812S48493
200-240 AC/DCS47363S33813S48494
277 ACS47364S33814S48495
380-480 ACS47365S33815S48496

MX operating time at Vn:  50 ms ±10 (NW and NT)
XF operating time at Vn:  
70 ms ±10 (NW ≤ 4000 A)
80 ms ±10 (NW > 4000 A)
55 ms (NT)

NOTE:  Shunt trip (MX) and shunt close (XF) circuits must be energized for a minimum of 200 ms. In other words, don't use an impulse signal. Use a signal of at least 200 ms.
Show More