The Saturn Zen 2 gang plate accommoddates 30m35 mech is Z4032VH.
No. Unfortunately, part number 30M35 CANNOT be used in 2031V66.
Part codes which are available in 3S - 30M, 30USM, 30MI, 30MD, 30MBPR, 30M35, 32E450UDM, 32E450LM, 32E450TM
The 30M35 does not come in dark grey.
However it does come in Chrome Shadow or Soft Grey.
For further information please visit https://www.clipsal.com/Trade
No. We have 30M35 which is 1 pole, 35A mech.
No there is no saturn mech available. There is either the Z4061/45 cooker switch plate or the 30M35 in a Z4031VH Plate
The part number is 30M35-3S, but not anymore available for sale in New-Zealand.
The part number 30M35 mech will go into 4031VH plate.
If you want 2 stove switches in one plate, you would need to use Clipsal 4032VH and 30M35 and for the telephone use a 30BTM and 4031VH
There is no dedicated range switch in the slimline series. The 30M35 (35A 30 series mech) can be installed into a single grid plate SC2031VH.
No, There is no 32A switch mech to fit into the Z4061VH plates, The solution would be to use the 30M35 (35A 30 series mech) in a Z4031VH plate.
There is no dedicated cooker switch in the BSL range however, you could use a 30M35 mechanism in a BSL31VH plate.
For further information please visit https://www.clipsal.com/Trade
There is no 32A mech that fits directly into the 406* plates,
The 60R32-** and 60R32COOK-** will only fit into the extra switch position on the 4025XA-**
For a standard plate with a 32A mech you will need to use a 403* plate with a 30 series 35A mech, 30M35
No , The 60R32 series mechs are only designed to go into the 4025XA and 4025XUA plate styles. If Mechs over 32 amp are required for Saturn plates then you will need either 4031VH plate and 30M35 series mechs or the dedicated cooker plates 4061D32 or 4061/45 series
The alternative part for the Clipsal 30M20 is the 30USM: Universal Rocker Switch, 1-Way/2-Way, 250VAC, 20A.
Yes the part number is RCD240/30.
The 30MBP has been tested to 12000 cycles.
No - It is just a 2 pole switch
But a 30MD2 is a 2p 2way (6 terminals)
The part code is 30M-3A are available but indent
The cooker switch is one switch for on and one switch for off
No, but you can use a 4031VH and a 30MD.
The replacement for a Merlin Gerin 26860, RCBO, 240V, 20A, 30mA is a A9D11820.
The replacement part number for MRCD20-30, 2 pole, 20A, 250V, 30mA, IP66 RCD is 56RC
is also 2 pole, 20A, 250V, 30mA, IP66 RCD.
For further information, please visit
The closest alternative to a 30MBP momentary bell press mechanism is a 30PBBP.
The older unit was 15A compared to the new version at 16A. The 30PBBP has a square body but mechanically they are the same operation
Both Colours are not available for that Part.
The part number is 16924.
Do we offer a flashing 24V pilot light in the 9001 30mm line? What is the part number for a Flashing amber 24 vdc pilot light 30mm?
30mm Push Buttons
9001K/SK light modules
Looking for a flashing pilot light.
This is not offered in the 30mm lines.
As energy accumulates, the ION 6200 digital output toggles from Open to Close, or from Close to Open, instead of pulsing. This is called KY pulsing. By default, the ION6200 meter has two Pulser modules preset to send pulses every 1 kWh and every 1 kVARh to the 2 solid state relays on the meter. The settings on the front for the defaults are out1 = wH, tc 1 = 1 and out2 =VArh, tc = 1. Notice that both out1 and out2 do not show k(kilo), but all out settings are in k(kilo), and that the tc(time constant) setting is also referenced as kT in some cases.
Here are some parameter limits and operational constraints to keep in mind for the ION6200 meter:
- Maximum Transition frequency = 20 per second
- Minimum Period between Transition = 30ms, fixed
- Kt Value must to set to a value greater than 0.1 for the digital output to operate correctly and accurately. This is due to bounds on the internal accuracy of the values maintained within the meter.
Note also that the digital output toggles in batches at the beginning of each second. Thus, the digital output operates in bursts potentially at the beginning of each new 1 second boundary for no more than 600ms (20 transition x 30ms) in each one-second cycle. Calculations can be made to show that this implies that accuracy of measurements derived from this meter's pulsing capability must be averaged over at least a 15 minute period in order for them to reliably fall within the 0.5 accuracy class of this meter. This is not a reflection of the accuracy of the meter's measurement capability so much as a consequence of the specific way that this meter outputs measurement data via its digital outputs.
SCCR ratings for 9080LBA power distribution block
Power Distribution Blocks
The 9080LBA and 9080LBC terminal blocks have been tested with SCCR ratings up to 100kAIC. See the attached catalog, pages 30-36 for details.
2031VETR3 is three wire switch.
Additional switches, 30mbp or the 30pbbp, can be installed in parallel to activate the timer from more than one location.
Please go to the website via the following link www.clipsal.com/Trade/Products/ProductDetail
and check under the Documentation Tab for more information.
Any 240V momentary switch, such as a 30MBP Bell Press Switch can be wired to either of the two new mounting bases 755RB or 755RFB up to 20m away. A relay can also be pulsed on momentarily via a security or home automation panel to activate the test/hush function.
What is the VA rating of a 9001KM 120V LED light module?
Push Buttons and Operator Interface
30mm, 9001KM, 9001K, 9001SK
All 9001KM 120V LED: 9001KM38LR, 9001KM38LG, 9001KM38LY, 9001KM38LW, 9001KM38LL have a 1.4VA rating.
What is the parts break down of a 9001KYK116?
Pushbuttons and Operator Inteface
30mm, 9001KY/SKY Control Stations
9001KY1 - Enclosure
9001K15 - Emergency Break Glass Operator
9001KA1 - 1NO and 1NC Contact Block
9001KN799RP - Legend Plate (Special Marking)
Outdoor rating for 9001K key-operated selector switch
No. There are no boots or covers available either .
What is the fuse or circuit breaker rating for LXM32 drives?
For 115VAC and 230VAC drives, the maximum fuse to be connected upstream is 25 Amps, Class CC or J as per UL 248-4, alternatively circuit breakers with B or C characteristic.
For 400VAC and 480VAC drives, the maximum fuse to be connected upstream is 30/32 Amps, Class CC or J as per UL 248-4, alternatively circuit breakers with B or C characteristic.
Electrical Distribution Equipment
The settings are 30ma, 100ma, 300ma, 500ma, 1A, 3A, 5A, 10A, 30A.
is the replacement for part number 4RCBM220G30. 4RCBM220SI30
is RCD/MCB, 2 module, 2 Pole, 20A, 30mA, 10KA, C-Curve SI-type, super immune, A-type, surge current protected to 3000 A 8/20ms.
For further information, please refer to the below link:
4RC225/30 is an alternate for 4EL25/2/30, 25A , 30mA, 2 module RCD.
- Unique new white finish for a fresh modern look
- Base module = 18 mm wide, compact standardised and consistent module dimensions
- Lift-up terminals. Safer ‘no hot spot’ terminations and all cable strands are locked in
- Cable automatically guided to the correct position: terminals with guard
- Fast closure
- The presence of the green strip guarantees physical opening of the contacts and allows operations to be performed on the downstream circuit in complete safety
- Same housing as AC type MCBs. Uniformity in space requirements and installation
- Superior, safe and reliable DC breaking per pole
- Used with marine, telecommunications, solar power, emergency power, battery power
- Excellent breaking capability for its compact size
- Standard type
- 75 mm modular spacing
- Surge current protected to 250 A at 8/20 uS
- Operating temperature: -5 to 40 deg C
- Degree of pollution is 2
- Rated Impulse withstand voltage is 6 kV
An extra switch can be wired to a majority of roller doors. However, you will need to contact your roller door manufacturer and request your roller doors specifications as the specifications may vary between products. If you fail to do so we will be unable to provide the correct part as we are unsure of the specifications such as current, voltages, wave type (AC or DC).
For more information on our product range please visit https://www.clipsal.com/Trade
What is the recommended spacing for 22mm pushbuttons ?
Horizontal spacing is 1.18`` or 30mm, vertical spacing is 1.57`` or 40mm, hole size 0.88`` ( recommended 0.89`` ) or 22.5mm