clip conduit pvc 20mm

Fixing Accessories, PVC, Conduit Clips and Mounting Channel, Conduit Clip 20mm

Catalogue Number: 280/20
clip conduit pvc 20mm
Colour: Grey
Colour: Per UOM Std.
  • Grey 1 PCE
Added to cart

Specifications

hide show
Product brand
Clipsal
Material
plastic
Length
27 mm
Width
12 mm
Height
29 mm
REACh Regulation
Free of Substances of Very High Concern above the threshold
REACh free of SVHC
Yes
EU RoHS Directive
Pro-active compliance (Product out of EU RoHS legal scope)
Toxic heavy metal free
Yes
Mercury free
Yes
RoHS exemption information
Yes
China RoHS Regulation
 Pro-active China RoHS declaration (out of China RoHS legal scope)
Circularity Profile
N/A

Documents & downloads

hide show
Filter items
  • All

  • Product Brochures

  • Technical Data Catalogues

  • Installation Instruction

  • Specifications

  • Certificates (MSDS)

Frequently Asked Questions

hide show

Are the Clipsal Conduit Clips available in Electric Orange?

No, they are only available in grey.

This applies to the 280/16 (16mm), 280/20 (20mm), 280/25 (25mm), 280/32 (32mm), 280/40 (40mm) and 280/50 (50mm).

Can I order the 220/20 in white?

Yes, you can order the 220/20 in white but it needs to be done as a special.
For more information, please refer to the link:https://www.clipsal.com/Trade/Products/ProductDetail?catno=220/20

Is part number 260/25 available in Orange?

No. Unfortunately, the 260/25 is only available in Grey.

What would be a longer screw to suit Clipsals round j-boxes (Junction Boxes)?

The part number would be 248/20 which is a combination screw head 20MM 3/16 BSW.

Do you have a cap/ flange to for 20mm conduit?

Yes the part number is 221/20

What is the replacement AC coil for CAD32 and CAD50 relay?

Issue:
Are replacement  AC coil available for CAD32 and CAD50 relay?

Product Line:
Tesys Relays

Environment:
All Products

Cause:
Product selection

Resolution:
Volt = coil part number
12 = LXD1J7
21 = LXD1Z7
24 = LXD1B7
32 = LXD1C7
36 = LXD1CC7
42 = LXD1D7
48 = LXD1E7
60 = LXD1EE7
100 = LXD1K7
110 = LXD1F7
115 = LXD1FE7
120 = LXD1G7
127 = LXD1FC7
200 = LXD1L7
208 = LXD1LL7
220/230 = LXD1M7
230 595 21 LXD1P7
230/240 = LXD1U7
277 781 30 LXD1W7
380/400 = LXD1Q7
400 = LXD1V7
415 = LXD1N7
440 = LXD1R7
480 = LXD1T7
600 = LXD1X7
690 = LXD1Y7

 

Is there a black version of the 220S20?

Yes, there is.  The 220S20 comes in 3 colors.

For more information, please refer to the link:
https://www.clipsal.com/Trade/Products/ProductDetail?catno=220S20 

Looking to replace the LXM23DU04M3X and BCH0602O12A1C

Issue:
Looking to replace the LXM23DU04M3X and BCH0602O12A1C servo motor

Product Line:
LXM23

Resolution:

The direct replacement is:
 
LXM28AU04M3X and BCH2LD0431CA5C combination:
 
- Supply voltage single phase 200/240 VAC or 3 phase 200/240 VAC, 50/ 60 Hz
- Nominal torque 1.27 Nm
- Maximum peak torque 3.81 Nm
- Nominal speed 3000 RPM
- 0.4 Kw motor rating
- 0.27 kgcm2 motor inertia without holding brake
 
You cannot copy the parameters from the old drive to the new drive. They will have to be entered manually in the new LXM28 drive.

What is the part number for a 50mm female and 50mm male bush?

The part number for a 50mm female and 50mm male bush is - 281/50 & 281F50
For further information , visit link below:-
www.clipsal.com/Trade/search-results?q=281/50
https://www.clipsal.com/Trade/search-results?q=281F50
User-added image

 

Latest Firmware version of Com'X 200/210 and Natively supported device type in the Energy Server Com'X 200/210

Product Line
COM'X200 / EBX200
COM'X210 / EBX210
 
Environment
Ethernet Gateway supported devices
 
Resolution
The latest version of firmware for Com'X 200 is 3.5.15 and the Com'X 210 is 4.0.10. Please find the firmware files below.
They can be downloaded from the following links as well.
COM'X200 firmware
COM'X210 firmware
 
In addition, review the attached PDF (DeviceList_ComX200_210_2.2.1.pdf) for the list of Natively Supported Device Types on Com'X 200/210 with Firmware Version 2.2.1.
Note: With firmware 3.5.24, the Com'X 210 also supports Masterpact MTZ and the EM4399.

For instructions on how to upgrade the firmware, view article FA270261.

How do i seal up a 50mm hole in the 230DRAVL?

Using parts 220S50-GY and 260/50-GY. Placethe 260/50 on the inside and the 220S50 on the out side place it in the hole and screw them together. This willl then seal the hole.

For further information please visit https://www.clipsal.com/Trade/Products/ProductDetail?catno=260/50
https://www.clipsal.com/Trade/Products/ProductDetail?catno=220S50
 
 
 

How can you configure the ATV32 drive to use assemblies 20/70 and 21/71?

Issue:
How can you configure the ATV32 drive to use assemblies 20/70 and 21/71?

Product Line:
Altivar ATV32

Environment:
ATV32 with Ethernet option card installed

Cause:
Set up configuration to use assemblies 20,21,70 and 71.

Resolution:
See case #2 example in the following attachment.
 

Typical 3-line drawings for Sepam Series 20, 40 and 80 current and voltage input connections

Goals and Symptoms

Typical 3-line drawings of Sepam 20/40 Feeder, Sepam 20/40 Main and Sepam 80 Main/Feeder.

Causes and Fixes

See attachment
Sepam.zip



AEDL3
Legacy KB System (APS) Data: RESL203669 V1.0, Originally authored by MiZe on 10/09/2010, Last Edited by MiZe on 10/09/2010
Related ranges: Sepam series 80, Sepam series 40, Sepam series 20

What is the accuracy of the Premium PLC CPU real time clock.

Real time clock accuracy:

Accuracy of the real time clock is one second (%SW50) +/- 200ms.

Resolution of the real time clock is one second (%SW50) +/- 200ms,because 200ms is the refresh rate of the RTC.
 
Accuracy error:
 
The accuracy error of the quartz oscillator is:
 
1. At 0 and 70°C : -101/20 ppm, error in second/day is -8.7/1.7, in minute/year is -53/11.
 
2. At 25°C: -20/20 ppm, error in second/day is -1.7/1.7, in minute/year is -11/11.

What is the part number of the surface mounting box that has a duct entry?

The part number of the surface mounting box that can accept a duct is 900SPMB. The 900SPMB is a standard pattern Surface Mounting Box for single gang accessories. Internal depth - 33mm.
Features: 4 - 25 x 16mm Trunking Entries, including one each end and side.
Supplied with 3 - Cat. No. 900MBC Clip-in/ push out caps, 4 - Cat. No. 220/10 Insulating Caps and 2 - M3.5 x 0.8 x 16mm long pan head screws. Screws thread into brass inserts.
For further information, please visit https://www.clipsal.com/Trade/Products/ProductDetail?catno=900SPMB

 

What are the part numbers of slip type expansion couplings?

Slip Type Expansion Couplings are available from 16mm through to 50mm.The part numbers of slip type expansion coupling are as follows:
16mm = 251/16
20mm = 251/20 *
25mm = 251/25 *
32mm = 251/32
40mm = 251/40 *
* = only available in Grey
Where long conduit runs are likely to be exposed to wide variations in temperature, it is recommended that expansion couplings be used at each join. It is not recommended that Slip Type Expansion Couplings be used where the conduit run is exposed to the weather. Standard colour is Grey (GY).
Dimension details are attached.
 

How do I hardwire 10kva and 20kva transformers in a 208/120 or 240/120 environment

Issue:
Implementing a hardwire stepdown transformer in a 208v or 240v environment


Product Line:

Smart-UPS / Symmetra

Environment:

APTF10KT01, APTF10KW01, and APTF20KW01, All Serial Numbers

Cause:

Unbalanced UPS outputs require a stepdown transformer to power 120v loads


Resolution:

This document refers to installing  the APTF10KT01, APTF10KW01, and APTF20KW01 transformers in a North American 120/240 or 120/208 environment. For installations in other regions please consult the users manual.

The wiring block outputs are as follows:


For domestic use, make sure that the Terminal Block Jumper is installed between the Ground Terminal and Terminal 8 on the output wiring block, as illustrated on page 8 of the user manual. Please also make sure that the input voltage switch is in the correct position.

The step-down transformer provides 240/120 output as 2 120v hots, a neutral, and a ground. It provides 208v output as a 120v hot, an 88v hot, and a ground. The 120v hot (terminal  7) and the 88v hot (terminal 9) are 180 degrees out of phase. You will measure 208v from terminals 7 to 9. The step-down transformer is not able to provide 2 120v hots that are 120 degrees out of phase as you would see with utility power.



 Note: If your installation requires both 208v and 120v output power you will need 2 separate subpanels: a 240v/120v panel and a dedicated 208v subpanel.

What is the part number for a Contactor with Low consumption?

The part number for a low consumption contactor is LC1D09.
General Product information:
Range of product TeSys D
Product or component type Contactor
Device short name LC1D
Contactor application Motor control Resistive load
Utilisation category AC-1, AC-3
Poles description 3P
Power pole contact composition 3 NO
[Ue] rated operational voltage <= 300 V DC for power circuit
<= 690 V AC 25...400 Hz for power circuit
[Ie] rated operational current 9 A (<= 60 °C) at <= 440 V AC AC-3 for power circuit
25 A (<= 60 °C) at <= 440 V AC AC-1 for power circuit
Motor power kW 5.5 kW at 660...690 V AC 50/60 Hz
5.5 kW at 500 V AC 50/60 Hz
4 kW at 415...440 V AC 50/60 Hz
4 kW at 380...400 V AC 50/60 Hz
2.2 kW at 220...230 V AC 50/60 Hz
Motor power HP (UL / CSA) 7.5 hp at 575/600 V AC 50/60 Hz for 3 phases motors
5 hp at 460/480 V AC 50/60 Hz for 3 phases motors
2 hp at 230/240 V AC 50/60 Hz for 3 phases motors
2 hp at 200/208 V AC 50/60 Hz for 3 phases motors
1 hp at 230/240 V AC 50/60 Hz for 1 phase motors
0.5 hp at 115 V AC 50/60 Hz for 1 phase motors
Control circuit type AC 50/60 Hz
Control circuit voltage 415 V AC 50/60 Hz
Auxiliary contact composition 1 NO + 1 NC
[Uimp] rated impulse withstand voltage 6 kV conforming to IEC 60947
Overvoltage category III
[Ith] conventional free air thermal current 10 A at <= 60 °C for signalling circuit
25 A at <= 60 °C for power circuit



For more information please visit https://www.schneider-electric.com.au/en/productcontaLC1D



Com'X 200 / 210 / 510 Documentation (Technical Datasheet, User Guide, and Installation Guide)

Issue
Documentation for COM'X 200/210/510 is needed

Product Line
Com'X 200 (EBX200)
Com'X 210 (EGX210)
Com'X 510 (EBX510)

Environment
Documentation

Resolution
The documents below include Technical Datasheet, User Manual, and Installation Guide

Com'X 200/210/510 Installation Guide:5406AD002
Com'X 200/210 User Manual: DOCA0036EN
Com'X 510 User Manual: DOCA0098EN
Com'X 200/210/510 Technical Datasheet: PLSED310098EN
 

Video: What is the default grid snap setting in Vijeo Designer v6.2?

The default spacing is 20x20 pixels.  It can also be changed from the Graphical Panels Properties.

The following video demonstrates adjusting the grid snap spacing in Vijeo Designer via the Graphical Panels Property Inspector.

 

Customer is looking for a sizing tool for Schneider Electric solar products.

Customers are looking for a sizing tool for there solar projects or installations with Schneider Electric products. 

We can provide the customer with a Conext Designer tool which includes the following products:

Conext TX inverters
Conext Core XC
Conext TL
Conext RL
Conext CL
XW-MPPT 80/60

Download link for the Conext Designer:
https://schneider-electric.box.com/s/g5yyi93prdtogi877yu2




 

What is the part number for the Relay and RPO connector for the Conext CL inverters?

One set of dry contact Relay and RPO connectors are provided along with the wiring box packaging.
The Relay and RPO connector is included in a plastic bag with other connectors, if it is lost, you will have to purchase another one.
The part number is 0J-0L2344 (Lit Kit IEC CL 20/25 kw Rohs package)

What is the replacement mechanism for the surge protection in a 2025SF?

The replacement for the surge protection in a 2025SF is the 30SFM.

Some of the key features are:
  • Peak current (8/20µs) 6.5 kA
  • Maximum clamping voltage (8/20 µs, 100 A) 710 V
  • Energy absorption (10/1000 µS) 3 x 140J
  • Impulse response time <50 ns

For further information please visit https://www.clipsal.com/Trade/Products/ProductDetail?catno=30SFM



 

Does the Com'X 200/210 or Com'X 510 support the Powerlogic and SY/MAX protocols?

Issue
A user needs to know if the Com'X 200 / Com'X 210 / Com'X 510 supports the Powerlogic and SY/MAX protocols

Product Line
Com'X 200/EBX200
Com'X 210/EBX210
Com'X 510/EBX510

Environment
Gateway Portocol Support

Cause
A user needs to convert legacy device protocols such as Powerlogic and SY/MAX from CM2000 series, CM200 series, CM100 series, etc. to Modbus TCP/IP.

Resolution
The Com'X 200, Com'X 210 and Com'X 510 do not support the Powerlogic or SY/MAX protocols.
Use an EGX100 or EGX300 to convert Powerlogic or SY/MAX to Modbus TCP/IP. However, EGX100/300 have been obsoleted and the replacement is EGX150. EGX150 supports the Powerlogic or SY/MAX protocols as well.

Com'X 200 supported Protocols:
IPv4
IPv6 - HTTP
HTTPS
Modbus TCP/IP

Com'X 510 supported Protocols:
HTTP
HTTPS
FTP
SMTP
Modubs TCP/IP

Video: How to Reset the Web page Password to factory values for Com'x 200/210 and 510?

Issue
If the web-page password is lost, user would like to reset the password to factory default values. 

Product Line
Com'x 200, Com'x 210, Com'x 510

Cause
User has lost their password to login into web-page of Com'x gateway and they would like to reset password to default values.

Resolution
If the web-page password is lost, follow the procedure below in order to reset the password to factory default values: 
  1. Press the Backup button (number 7 shown in screen shot below) on the Com'x 200 (or 510) from front panel and hold it for 10 seconds until the power LED flashes green 3 times.
  2. Release the button. 
  3. To access to the Com'x configuration web pages, use these settings: 
                     Username: admin
                     Password: admin



Wrench Icon flickers on the Series 700 or 200 Power Meter (PM200 or PM700)

Product Line
PM700 Series
PM200 Series

Environment
Firmware

Cause
A possible reason for the flickering wrench icon to occur is a relatively low load of approximately 500 to 525 mA RMS being applied on the current inputs of the PM200 or PM700 (with firmware version 2.020 or previous). This low load will cause the gain change to flip back and forth between low and high gain. This causes the wrench icon to flicker on and off due to clipping during high gain at the transition point.

Firmware version 3.050 or later will check the peak amplitude prior to changing from low gain to high gain and delay the transition to high gain to prevent clipping.

Resolution
The Series 700 and 200 Power Meters with firmware 2.020 requires a firmware update to version 3.050 or above.

To verify the firmware version from the front panel of the meter, press MAINT > INFO for the PM700 and press DIAGN > INFO for the PM200.

See FA237920 for latest firmware, firmware upload software, and instruction on how to upgrade the firmware.

Using Modbus to trigger a Waveform Capture on a CM2000

Product Line
CM2000 series meter

Environment
Modbus Register Writes

Resolution
In order to trigger a waveform capture, it will be necessary to use Modbus Command Writes to trigger the waveform capture.

Using Modbus Tester (or another Modbus read/write program):

Write the value 4913 to register 7700.
Write the value 1 to register 7701.
Write the value 28120 to register 7702.

Why are PM700s pulse weights different on different PM700s?

Issue
Some PM700 have the possibility for adjusting pulse weight to 0.01 kWh/pulse even though the documentation says the minimum value that can be set is 0.1 kWh/pulse.

Product Line
PM700

Environment
Firmware

Cause
OS 2.020 added a higher amount of accuracy for the pulse weight option.

Resolution
With firmware OS 2.020, the lowest pulse weight value that can be set on the meter was reduced from 0.1 to 0.01kWh/pulse. That is to say, starting from firmware version OS 2.020, lowest pulse weight option is now 0.01 kWh/pulse instead of .1 kWh/pulse. 

IP protection and gas

Goals and Symptoms

Need to know if the power part with IP54 degree of protection (where is placed the heatsink), of Altivar 71 and 31 is proof (resistant) against the following chimical compound: NPK 8/24/24 - PK 9x36 - UREA 46% N - H8 N2 O4S - PK 14x24 - PK 20x20 - Mg SO4 7 H2O - KC1 60% K2O - K2 SO4 50% K2O - (NH4) 2 HPO4 - NH4 H2 PO4 - Ca (H2 PO4) 2 and "ammonium nitrate" with a percetage of nitrogen. I apologize for the "strange" question but I kindly ask you help for to give an answer to our customer. Please take care of this request ASAP because is very urgent (our PAE should give an answer for tomorrow).

Facts and Changes

heatsink

Causes and Fixes

Attached is a document with the protection again gas for our drive. The standard IEC721-3-3 is taken as a reference.

How to control the frequency of the VFD over the network when using output assembly 20 or 22 when using DeviceNet or Ethernet IP?

Issue: 
How to control the frequency of the VFD over the network when using output assembly 20 or 22 when using DeviceNet or Ethernet IP?
 
Product Line:
Altivar 61, Altivar 71
 
Environment:
All serial number
 
Cause:
VFD will not respond to speed control from the network when the reference channel is programmed to Comm card and the drive shows the active reference channel is Comm Card.
 
Resolution:
When using output assembly 20 or 22, by default, the Net Ref parameter is set to 0.  This parameter must be set to 1 in order to control the speed from the network for Devicnet or EtherNet IP.   The net ref parameter must be set on each time the VFD is powered.
Net Ref parameter 2A/1/4 = 1
The address can be set with the Class Instance Editor or with a message instruction block.

How do I bring the Com'X Analog Inputs into Power Monitoring Expert (PME)?

Issue
The Com'X is not a native device in PME.

Product Line
Power Monitoring Expert 7.x
Power Monitoring Expert 8.x
EBX200, Com'X200
EGX510, Com'X510

Environment
Power Monitoring Expert Modbus Device Importer

Resolution
To bring the device into PME:
  1. Install the Com’X via the Instruction Manual, wiring the Analog Inputs and Ethernet connection.
  2. Connect to the Com'X via its webpage and add the Analog Input via the Com'X User Guide.
    1. Select the Custom Library tab > + Create.
 
  1. Customize the model and select Create.
 
  1. Configure the properties of the model (i.e. scaling and units) and Save changes.
 
  1. Add the device in Device Settings.
    1. For the appropriate Analog Input, select 'Create a new device' for the Device dropdown menu.
 
  1. Select the previously created Device Type in the Device Type dropdown menu.
  2. Configure the device and select Create.
 
The data is now available within the Com'X webpage under the Measurements Table tab. The measurement will be associated with the Commodity specified in step 2.5.
  1. If using a Com'X 510 with firmware v3.0.6 or Com'X 200/210 with firmware v2.2.1, Enable Modbus TCP/IP on Ethernet 1; otherwise, continue onto Step 4.
    1. ​Select the Settings tab.
    2. Under Security > Firewall Management, switch the Enable Modbus TCP/IP on Ethernet 1 to ON
 
  1. Verify that Ethernet 1 is the Ethernet port being used to communicate to the PME server.
 
  1. In PME, create a device type using the Modbus Device Importer
    1. Open Management Console.
    2. Select Tools > System > Modbus Device Importer.
 
  1. Select Edit > Advanced Properties and rename the Device Type and check the "Make available as a direct Ethernet device in Management Console" box. Click OK.
  2. Select Edit > New Manager
    1. Manager Name: Analog Input
    2. Manager Type: External Numeric Manager
 
  1. Add a new Module for Analog Input 1 (**IF USING Analog Input 1)
    1. Add a new Register
      1. Data Type: IEEEFloat
      2. Register Type: Holding Register
      3. Modbus Address 410000
      4. Request Type: R
      5. Use the attached MDI_parameter_calc_for_ComX_AI.xlsx to calculate the appropriate Register Scale, Multiplier, and Offset value.
  2. Add a new Module for Analog Input 2 (**IF USING Analog Input 2)
    1. Add a new Register
      1. Data Type: IEEEFloat
      2. Register Type: Holding Register
      3. Modbus Address 410002
      4. Request Type: R
      5. Use the attached MDI_parameter_calc_for_ComX_AI.xlsx to calculate the appropriate Register Scale, Multiplier, and Offset value.
  3. Save the device type.
  4. Select Tools > Validate Template and verify that there are no errors.
  5. Configure Logging and Calculation.
    1. Select Configure Logging and Calculation
 
  1. Check "Log" to enable logging for the desired register.
 
  1. Specify the desired Log Interval in seconds.
  2. Press OK.
  3. Save the device type.
  4. Select Tools > Add Device Type
  1. Open Management Console and Add the Device
    1. Select Devices in Management Console.
    2. Right-click and select New > Ethernet Device
    3. Enter the desired Group and Name.
    4. The Device Type will be the name specified in step 4.3.
    5. Enter the IP address of the device
    6. Click OK.

The referenced Com'X 200 / 210 / 510 Documentation is available here: https://www.schneider-electric.us/en/faqs/FA289876/

Where can I get support for APC and MGE Products?

For support on APC and MGE products please visit:  https://www.apc.com/support/

AC Power
Additional Management Cards and Options
Air Cooled Chillers
Air Distribution Accessories
Airflow Management
AIS 3000
AIS 5000
AIS Accessories
AIS Battery Systems
APC CS
APC Enterprise Manager
APC ES
APC RS
Application Shutdown Utilities
Assessment Services
Auto and Air Inverters
AV Accessories
AV Power Conditioners & Battery Backups
AV Power Filters
AV Pro Interconnects
AV Surge Protectors
Backpacks and Messenger Bags
Back-UPS
Back-UPS Accessories
Back-UPS BI
Back-UPS CS
Back-UPS ES
Back-UPS HI
Back-UPS HT
Back-UPS LS
Back-UPS Office
Back-UPS Pro
Back-UPS RS
Back-UPS XS
Basic Rack PDU
Battery Management
Battery Replacement Services
Biometric Security
Bulk Cable
Cabinet Power Distribution
Cable Management
Charge-UPS EX
Commercial/Industrial Surge Suppression
Condensers
Configurable Power Accessories
Configurable Power Distribution
Console Port Servers
CyberFort
Data Center Facility Cooling - Andover Continuum or TAC Vista
Data Center Facility Power - PowerLogic ION Enterprise
Data Center Software Integration Kits
Data Center University
Data Distribution Cable
DC Battery
DC Components
DC Distribution Components
DC600
Desktop KVM
Desktop Notebook Stands
EcoBreeze Air Economizers
Environmental Management System
Environmental Monitoring Unit
Ethernet Switches
Extended Warranties
Fiber Optics
Firmware Upgrades
FLM Series
Fluid Coolers
FRP/Ferroresonant Power Supply
Game Console Surge Protection
Gender Changers
Global Deployment
Hardwire Surge Suppression Accessories
High-Density Cooling Enclosures
IDE Cables
IEEE1394
Industrial
InfraStruxure for Large Data Centers
InfraStruxure for Medium Data Centers
InfraStruxure for Server Rooms
InfraStruxure for Small Data Centers
InfraStruxure for Wiring Closets
InfraStruxure Manager
InfraStruxure Type A
InRoom Direct Expansion
InRow Chilled Water
InRow Direct Expansion
InRow Pumped Refrigerant
Installation Services
Interface Cables
International Plug Adapters
Keyboard
KVM Switches
Laptop Power Adapters
Line-R
Magnum VS
Magnum XS
Magnum XS Rectifier
Maintenance Bypass Panels
Management Platform Integration
Matrix Battery Systems
Matrix-UPS
Matrix-UPS Accessories
Metered Rack PDU
Metered-by-Outlet Rack PDU
MGE Accessories
MGE Alpes
MGE Battery Systems
MGE Comet
MGE EPS
MGE EPS 6000
MGE EPS 7000
MGE EPS 8000
MGE Galaxy
MGE Galaxy 300
MGE Galaxy 3000
MGE Galaxy 3500
MGE Galaxy 4000
MGE Galaxy 5000
MGE Galaxy 5500
MGE Galaxy 6000
MGE Galaxy 7000
MGE Galaxy 9000
MGE Galaxy PW
MGE Legacy
MGE Service Bypass
MGE Sinewave
MGE Static Transfer Switches
MGE UPS 4000
Microsol Estabilizadores
Microsol Modules Isoladores
Mobile Notebook Stands
Modular Components
Modular Power Accessories
Modular Power Distribution
Monitor
Mounting Hardware
Mouse
MRC1800
MRE2400
Multimedia
MWF1700
NetBotz 200
NetBotz 300
NetBotz 400
NetBotz 500
NetBotz Access Control
NetBotz Accessories and Cables
NetBotz Central
NetBotz Rack Access
NetBotz Sensors
NetShelter CX
NetShelter EP Enclosures
NetShelter ES Enclosures
NetShelter Open Frame Rack Accessories
NetShelter SX
NetShelter VL
NetShelter VS Enclosures
NetShelter VX Enclosures
Network Integration Services
Network Patch Cables
NetworkAIR Accessories
NetworkAIR AFX
NetworkAIR CM
NetworkAIR CW
NetworkAIR FM
NetworkAIR IR
NetworkAIR TC
Notebook Security
On Site Service
Open Frame Racks
Operations Capacity
Operations Change
Operations Energy Cost
Operations Energy Efficiency
Operations Insight
Operations Mobile
Operations VIZOR
Outdoor Enclosures
Panelmount Environmental Monitoring
Parallel
Patch Panels
PC1200
Planning Tools and Publications
Portable Cooling
Power Cords
Power Distribution Units
Power Generation Systems
Power Ready Notebook Cases
PowerChute Business Edition
PowerChute Inventory Manager
PowerChute Network Shutdown
PowerChute Personal Edition
PowerChute plus
PowerManager
PowerShield
Preventive Maintenance
Project Management Services
ProtectNet
Rack Air Distribution
Rack Components
Rack LCD Consoles
Rack PDU Accessories
Rack-mount Transfer Switches
Refrigerant Distribution
Remote Monitoring Services
Replacement Batteries
Replacement Notebook Batteries
Residential Hardwire Surge Suppression
Retail
Retractable Cables
Room Air Distribution
Room Cooling Accessories
Router Cables
Row Cooling Accessories
SCSI
Security Cameras
Sensors
Serial
Service Bypass Panel
Service Plans
Silcon
Silcon Accessories
Silcon Battery Systems
SLM/FLM Series
SmartSlot Expansion Chassis
Smart-UPS
Smart-UPS Accessories
Smart-UPS Battery Systems
Smart-UPS DP
Smart-UPS On-Line
Smart-UPS RT
Smart-UPS VT
Software Configuration
Software Education
Software for NetBotz Appliances
Software Installation
Software Integration
Spare Part Kits
Specialty Enclosures
Start-Up Service
Stationary Power Distribution Units
Step-Down Transformer
StruxureWare Central
StruxureWare Operations Suite
SurgeArrest Essential
SurgeArrest Home/Office
SurgeArrest Notebook
SurgeArrest Performance
Switch Boxes
Switched Rack PDU
Symmetra
Symmetra Accessories
Symmetra Battery Systems
Symmetra MW
Symmetra MW Accessories
Symmetra Power Module
Symmetra PX
Symmetra PX Accessories
Sync and Charge Cables
Thermal Containment
Thick and Thin Ethernet
Token Ring
Toploading Cases
Traditional Cases
Training Services
Transceivers
Transportation
Travel Mice
TSP Accessories
TSP Battery
TSP/Generator
TSP/Total System Power
Tune-UPS for Symmetra
Uniflair Chilled Water
Universal Mobile Device Batteries
Universal Notebook Batteries
Universal Notebook Power Adapter
Universal Power Accessories
Universal Power Adapters
UPS Network Hub Card
UPS Network Management Cards
USB Adapters & Converters
USB Cables
USB Charging Cables
USB Hubs
Wall-mount Transfer Switches
Wheeled Cases
Wireless
Wizards and Configurators
WS200