The power supply to suit the 560125R/2 25W audio amplifier is a 5600P24H3750A.
What does the suffix 25K indicate on an MPZ device?
Mini power zone
MPZ mini power zone
The 25K suffix indicates the MPZ is rated at 25KAIC. The standard AIC is 18K. The 25K units have a higher rated 25K AIC primary main breaker installed, and so the entire unit AIC is then rated at 25K. Same for the 65K.
Yes, the extra switch in the 15X is removable. Any 230v rated 30 series mec will fit in it's place.
Yes, it can but you will need to put a 31CAP in parallel with the load.
286 MM Width, 258 MM height and 100 MM + wall thickness depth
The part number for the flap of 255 as a spare is 255FLAP-TR.
The maximum distance is 100m without obstructions, this is reduced to 25m if the receiver is enclosed in a metal enclosure.
The part name is A9F55325
Unfortunately it is not possible to have a publication time for less than an hour for either the Com'X 5xx or Com'X 2xx series units.
Part number is PDL 56SW332
Legacy Circuit Breakers
Electrical Distribution Equipment
The interrupt ratings below:
42k AIR at 240V
25k AIR at 480V
22k AIR at 600V.
No. However, you can assemble one yourself using a 25XD and a 30USBCM.
The part number for flap to suit 255 is 255FLAP-TR.
Yes, the 2025RCD30-WE will fit into a 255 weather protected box.The 2025RCD30-WE is 27mm deep and the 255 has 35mm depth. The bottom screwed plug will need to be shortened if not used as a cable entry.
Yes, the 25, Standard Series, double outlet,10A is available in the colour Blue. The part number is 25-DB.
Need the register list for my VAMP relay.
See the attached files for the VAMP 255 communications maps, this includes maps for:
Note: Latest information is available in m.vamp.fi
The aux contacts on all our contactors are rated at 10A Ith
No - the highest current rating is 25A
LC1D25BD is the correct part number
ISX Central's Internal Browser ""Home"" button doesn't work with 2.x NMC Firmware
InfraStruxure Central / Struxureware Data Center Expert.
InfraStruxure Central / Struxureware Data Center Expert
Any version 2.x firmware on APC SNMP enabled devices.
Any APC device running older 2.x firmware reacts differently due to coding differences.
There is no plan to update this feature at this time to work with the older devices.
The "H" at the end of the Modicon M340 part number stands for the "Ruggedized" version. This version allows the M340 to be used in more severe environments because of the protective coating on all their circuit boards and has an extended temperature range from - 25C to + 70C.
Legacy KB System (APS) Data: RESL209489 V1.0, Originally authored by DiSa on 10/25/2012, Last Edited by DiSa on 10/25/2012
Related ranges: Modicon M340
The part number for a Din rail mount 25A change over switch is a 4PS25CO
- Maximum 4 - Isolators - DIN rail mount
- Night, off, day switching of luminaries where daylight supplements internal lighting
- Incoming and outgoing terminals are screw down type and accommodate copper conductors up to 16 sq mm
- Auto, off, manual switching of machines
- Auxiliary, off, mains switching of small stand-by generators
For further information please visit https://www.clipsal.com/Trade/Products/ProductDetail?catno=4PS25CO
Issue: Need to know the operating voltage of the Vamp 255 digital inputs.
Product Line: Vamp 255
Resolution: The Vamp 255 has 2 sets of digital inputs. Digital inputs 1-6 are internally wetted with 48Vdc. The other 12 digital inputs operating voltage is defined by the part number ordering code:
A = 40 - 265 VAC/VDC
B = 18 - 36 VDC
C = 40 - 265 VAC/VDC + ARC Protection
D = 18 - 36 VDC + ARC Protection
E = 40 - 265 VAC/VDC + D19, DI20 + ARC channel
F = 18 - 36 VDC + D19, DI20 + ARC channel
Keywords: Vamp 255, Vamp 255 digital inputs, Vamp 255 operating voltage
An EGX continues to log a device despite the User Guide suggesting it should stop after a missed interval.
EGX300 Gateway Device
EGX Data Log
The table containing 'Error Codes for Data Logs' in the User Guide (pg. 39) states "Logging is left enabled unless the last interval was missed" for error codes 19 and 25. This suggests that the EGX should stop logging data from a device after an error appears. However, as seen in the image below, an error is observed more than once and the device continues to be logged.
Since the EGX300 is an obsolete device, it is unlikely the User Guide will be updated. This article will serve as a correction for the EGX300 User Guide's wording.
For this 4RCBM series range the KA rating is above 25a is limited to 6KA and below 25amps is 10ka.
new code = A9C20736 iCT Contactor 25A 2NC AC7a rated
6A - A9FDB606
10A - A9FDB610
16A - A9FDB616
20A - A9FDB620
25A - A9FDB625
FLC1 is the parameter to enter the Motor nominal current in TeSys T. In this parameter, the Motor nominal current is entered as a percentage of the rated value of the TeSys T.
For TeSys T of range 8Amps (LTMR08) and a motor of 2 Amps nominal current, you have to set the FLC1 value to 25% because the Motor nominal current is 25% of the full load current of TeSys T Module (LTMR08).
This means that the current in register 466 (value of current in percent) take the value of 100% when you reach 25% of the current of the TeSys T Module rated current value.
Options are NSY3X6625 - 600 x 600 x 250 or NSY3X7525 - 700 x 500 x 250
4RC225/30 is an alternate for 4EL25/2/30, 25A , 30mA, 2 module RCD.
- Unique new white finish for a fresh modern look
- Base module = 18 mm wide, compact standardised and consistent module dimensions
- Lift-up terminals. Safer ‘no hot spot’ terminations and all cable strands are locked in
- Cable automatically guided to the correct position: terminals with guard
- Fast closure
- The presence of the green strip guarantees physical opening of the contacts and allows operations to be performed on the downstream circuit in complete safety
- Same housing as AC type MCBs. Uniformity in space requirements and installation
- Superior, safe and reliable DC breaking per pole
- Used with marine, telecommunications, solar power, emergency power, battery power
- Excellent breaking capability for its compact size
- Standard type
- 75 mm modular spacing
- Surge current protected to 250 A at 8/20 uS
- Operating temperature: -5 to 40 deg C
- Degree of pollution is 2
- Rated Impulse withstand voltage is 6 kV
The BMXNOE0100.2 indicates a BMXNOE0100 with firmware version 2.x or higher.
Legacy KB System (APS) Data: RESL212295 V1.0, Originally authored by DaSo on 08/13/2013, Last Edited by DaSo on 08/13/2013
Related ranges: Modicon M340
TMSCE Manuals: Installation guide, User Guide.
The documents for the TMSCE 2.x software are attached.
The memory of M221 cannot be expanded. The M221 has the following types of memory:
RAM: 512 Kbyte, of which 256 Kbyte available for the application. It is used to execute the application and contains data
Flash: 1.5 Mbyte, of which 256 Kbyte is used to backup the user application and data in case of power outage. It is used to save the application
The SD card is only used to transfer the application or update the firmware
Yes, the part number for the flap / lid is 255FLAP-TR
Part number is actually 255FLAP -TR
- If you use the READ_VAR at address 130 with quantity = 1 you will get an error : CommError = 254 and OperError = 3.
- If you change the quantity = 2 you will still get the same error : CommError = 254 and OperError = 3: You will get the high order byte in %MW130 = 0 and lower order byte in %MW131 = 0.
The general register list for the Power meters gives you the Jbus addressing registers and not the Modbus addressing registers.
Jbus addressing starts a n and the Modbus addressing then should be n -1.
- If you now use the READ_VAR at address 129 (n -1) with quantity = 1 you will get the same error : CommError = 254 and OperError = 3.
- If you change the quantity = 2 life is good: You will get the high order byte in %MW130 = xxxx and lower order byte in %MW131 = xxx.
System: Pentium processor 500 MHz or higher
RAM memory: 256 MB
Hard disk space: 25 MB including the memory space for the software installation, temporary space for execution.
Operating System: Windows 7 or higher
Issue: Part numbers
Product Line: BMH
The part number for the power cable for a BMH1003 xxxxxx motor is VW3 M5101 Rxxx . where xxx = 15, 30, 50, 100, 150, 200, 250, 500, 750 for cable lengths 1.5m, 3m, 5m, 10m, 15m, 20m 25m 50m and 75 m respectively, The composition of this cable is [(4 x 1.5 mm^2) + (2 x 1 mm^2)] and comes with a pre-made M23 style industrial connector on the motor end and free ends on the drive side.
The part number for the feedback cable for a BMH1003 xxxxxx motor is VW3 M8102 Rxxx where xxx = 15, 30, 50, 100, 150, 200, 250, 500, 750 for cable lengths 1.5m, 3m, 5m, 10m, 15m, 20m 25m 50m and 75 m respectively, The composition of this cable is [(3 x 2 x 0.14 mm^2) + (2 x 0.34 mm^2)] and comes with a pre-made M23 style industrial connector on the motor end and an RJ45 style connector on the drive side.