coupling cond pvc expansion

Solid Fittings - PVC, Expansion Couplings - Slip Type, 16mm

Catalogue Number: 251/16
coupling cond pvc expansion
Colour: Grey
Colour: Per UOM Std.
  • Grey 1 PCE
Added to cart

Specifications

hide show
Product brand
Clipsal
Range of product
Series 251
Material
PVC (polyvinyl chloride)
Product destination
diameter: 16-16 mm tube
Length
57-70 mm
Standards
AS/NZS 2053
REACh free of SVHC
Yes
EU RoHS Directive
Pro-active compliance (Product out of EU RoHS legal scope)
Toxic heavy metal free
Yes
Mercury free
Yes
RoHS exemption information
Yes
China RoHS Regulation
 Pro-active China RoHS declaration (out of China RoHS legal scope)

Frequently Asked Questions

hide show

How many 261/16 Clipsal saddles are there in a carton?

There are 50 16mm saddles in a carton.

Note: This information can be found in your Clipsal pocketbook right next to the part code.

What are the part numbers of slip type expansion couplings?

Slip Type Expansion Couplings are available from 16mm through to 50mm.The part numbers of slip type expansion coupling are as follows:
16mm = 251/16
20mm = 251/20 *
25mm = 251/25 *
32mm = 251/32
40mm = 251/40 *
* = only available in Grey
Where long conduit runs are likely to be exposed to wide variations in temperature, it is recommended that expansion couplings be used at each join. It is not recommended that Slip Type Expansion Couplings be used where the conduit run is exposed to the weather. Standard colour is Grey (GY).
Dimension details are attached.
 

Can I get the 251/50 in orange?

No. Unfortunately, the 251/50 is the only one that comes in grey.

For further information please visit https://www.clipsal.com/Trade/Products/ProductDetail?catno=251/50



 

Are the Clipsal Conduit Clips available in Electric Orange?

No, they are only available in grey.

This applies to the 280/16 (16mm), 280/20 (20mm), 280/25 (25mm), 280/32 (32mm), 280/40 (40mm) and 280/50 (50mm).

What is the part code for a RCBO 4P 32Amp C-curve

 Combine a mccb 25016 32Amp C-curve with a 23382 rccb = RCBO

What are the dimensions for a 261S Saddle Spacer?

The dimensions for a 261S Saddle Spacer are 261S are:
 
Saddle Spacers
Catalogue Number Size Length (L) Width (W) Centres (CRS.) Standoff (T) Height (H)
261S16 16mm 55mm 21mm 32mm 8mm 14mm
261S20 20mm 61mm 22mm 40mm 8mm 14mm
261S25 25mm 74mm 26mm 48mm 8mm 14mm

Saddles Spacers set a conduit run off the wall 8mm to allow easier cleaning and repainting and to facilitate entry into equipment. They are available in sizes 16mm through 25mm.
Standard colour is Grey (GY), with Orange (EO) also available at extra cost.

For further information please visit www.clipsal.com/Trade/search-results?q=261S


 

Where are I/O modules installed on a PM8000 meter

Issue:
User wants to know where to install I/O modules on a PM8000 meter.
 
Product Line:
PM8000 meters
METSEPM89M2600 (Digital I/O module)
METSEPM89M0024 (Analog I/O module)

Environment:
I/O modules installation

Resolution:
*Warning:  Installation and maintenance of this device should only be performed by qualified, competent personnel that have appropriate training and experience with high voltage and current devices. Failure to follow the instructions / warnings in the Meter Installation Guide can result in permanent damage to the meter, severe injury or death.

There are 2 methods to install I/O modules on a PM8000 meter. The method to choose will depend on your PM8000 model number

If meter is PM8240 (Panel mount meter with integrated display)
I/O module to be installed on the back of the meter. 
1) remove connector's cover on back of the meter
2) Make sure that connectors on meter and I/O module align with each other. Attach I/O module to the back of the meter.
3) secure the I/O module in its location by a 5mm (5/16 in) screw
4) reattach connector's cover that was removed in step 1 to the back of I/O module
See illustration below:


If meter is either PM8243 or PM8244 (DIN rail mount meter)
I/O module to be installed on the side of the meter:
1) remove connector's cover from side of the meter
2) Hang the I/O module on your DIN rail
3) Secure I/O module to the DIN rail using Mounting clip.
4) Move I/O module using the DIN rail and attach it to the PM8000 meter> You should hear a click.
5) Secure the I/O module to the meter using a 5mm (5/16 in) screw.
6) reattach connector's cover that was removed in step 1 to the back of I/O module
See illustration below: