clip earth 32mm cond 25mm wp

Cable Management Pressed Metal Conduit Fittings, Earth Clip 32MM, 25MM WP

Catalogue Number: 209M
clip earth 32mm cond 25mm wp
Colour:
Colour: Per UOM Std.
  • 1 PCE

Specifications

hide show
Product brand
Clipsal
Material
steel
Surface treatment
hot-dip galvanized
Length
56 mm
Width
26 mm
REACh Regulation
Free of Substances of Very High Concern above the threshold
REACh free of SVHC
Yes
EU RoHS Directive
Pro-active compliance (Product out of EU RoHS legal scope)
Toxic heavy metal free
Yes
Mercury free
Yes
RoHS exemption information
Yes
China RoHS Regulation
 Pro-active China RoHS declaration (out of China RoHS legal scope)
Circularity Profile
N/A

Documents & downloads

hide show
Filter items
  • All

  • Product Brochures

  • Technical Data Catalogues

  • Installation Instruction

  • Specifications

  • Certificates (MSDS)

Frequently Asked Questions

hide show

Is part number 209M available in Stainless Steel?

The part number 209M is not available in Stainless.

What would be the part number for an Earth Clip, 16/20 mm.

203M.
Pressed Metal Conduit Fittings, Earth Clips, Water pipe adjustable earth clip 15 - 20mm or 1/2 - 3/4 inch.
Please see following link under the documentation tab for full catalogue.
https://www.clipsal.com/Trade/Products/ProductDetail?catno=203M

What is the part number of an hot dip galvanized earth clip to suit 3/4" conduit?

207M is a hot dip galvanized earth clip to suit 3/4"  or 20mm conduit. 

For further information, please visit https://www.clipsal.com/Trade/Products/ProductDetail?catno=207M


 

How can I find the serial number of a CM2000 by reading registers?

Issue
Finding the serial number of a CM2000

Product Line
CM2000

Environment
Serial Number

Resolution
The CM2000 serial number can be found by reading register 2096 and 2097. Use the following formula to find the serial number. If register 2096 is negative then the Serial Number = (reg.2097 x 2^16)+(reg.2096 + 2^16). If register 2096 is positive Serial Number = (reg.2097 x 2^16)+(reg.2096)

What is the part number for a 20mm conduit cap?

The part number for a 20mm conduit cap is- 262/20

 

What is part number for 20mm HFT corrugated conduit?

The part number for 20mm HFT corrugated conduitart is 9020CHF.

What is the overall dimension of 651A2-BK?

Overall dimension of 651A2-BK is 365 (W) x 209 (H) x138(D).

Do you have a cap/ flange to for 20mm conduit?

Yes the part number is 221/20

What is the part number for a 20mm steel conduit plug?

The part number  for a 20mm brass plug for steel conduit is 1220S20.

What is part number for 20mm HFT coupling?

The part number is a - 242HF20-BK




 

What is the part number for a 20mm steel coupling?

The part number for a 20mm steel coupling is 1242S20
Machined Brass and Steel Fittings, Steel Couplings, 20mm Steel coupling - zinc plated
For more information on this product please visit the Clipsal website on the link provided
https://www.clipsal.com/Trade/Products/ProductDetail?catno=1242S20

What is the part number of the reducer supplied with Weathershield isolators, 25mm plain, external, to 20mm threaded ,internal reducer?

The part number of the reducer supplied with weathershield isolators, 25mm plain, external, to 20mm threaded ,internal reducer is 222/2M-GY.

What is the part number for steel 20mm lockrings?

The part number for the 20mm steel lock rings is - 1259S20

For further information , please visit link below:-
https://www.clipsal.com/Trade/search-results?q=1259S20
User-added image

What is the part number for spacer for the 20mm saddles?

The part number for spacer for the 20mm saddles is - 261E20

For further information , visit link below:-
https://www.clipsal.com/Trade/search-results?q=261E20
User-added image

What is part number for Galv h/d 20mm junction box?

Part number not available in 20mm but its only available in 25mm and the part number is a 1240H25/2.
for more information on this part refer https://www.clipsal.com/Trade/Products/ProductDetail?catno=1240H25/2

User-added image

What is the part number for the Halogen free 20mm conduit?

The part number for the Halogen free 20mm conduit is - 9020HF

For further information , visit link below:-
https://www.clipsal.com/Trade/search-results?q=9020HF
User-added image

What is the part number for 20mm sheathed corrugated conduit?

The part number for 20mm sheathed corrugated conduit is - 9020CMS

For further information , visit link below:-
https://www.clipsal.com/Trade/search-results?q=9020CMS
User-added image

What is the part number for a 20mm 2 way conduit J-Box?

The part number for a 20mm 2 way conduit J-Box is - 240/20/2

For further information , visit link below;-
https://www.clipsal.com/Trade/search-results?q=240/20/2
User-added image

What is part number for 20mm brass barrel union?

The part number for 20mm brass barrel union is a 1242BU20

For more information on this part please refer to https://www.clipsal.com/Trade/Products/ProductDetail?catno=1242BU20

User-added image

Can you buy a 20m 954 camper set

You can purchase a 955RW, BALS211 + 56CR310 + flex

What is the part number for the 20mm double sided saddle that is Hot Dip Galvanised?

The part number for the 20mm double sided saddle that is Hot Dip Galvanised is - 172HDGM

For further information , visit link below:-
https://www.clipsal.com/Trade/search-results?q=172HDGM

User-added image

What is the part numbers for the 20mm & 25mm stainless steel saddles?

The part numbers for the 20mm & 25mm stainless steel saddles is - 172SS & 173SS.

For further information , visit links below:-
https://www.clipsal.com/Trade/search-results?q=172SS
https://www.clipsal.com/Trade/search-results?q=173SS
User-added image

What is the part number for a metal conduit J-Box with 1 x 20mm entry?

The part number for a metal conduit J-Box with 1 x 20mm entry is - 1239/20/1

For further information , visit link below:-
https://www.clipsal.com/Trade/search-results?q=1239/20/1
User-added image

What is the part number of the adaptor that can be used for 25 x16mm ducting to 20mm conduit?

900/25/16CA is the adaptor that can be used for 25 x16mm ducting to 20mm conduit.
For further information, please visit https://www.clipsal.com/Trade/Products/ProductDetail?catno=900/25/16CA
 

What is the part number for a conduit black HFT 20mm

Part number is 9020CHF, this is no longer available in NZ

What is the part number for a conduit bending spring

266MD20 - for 20mm medium duty conduit.
266MD25 - for 25mm medium duty conduit.

What code is an alternative for XCSE7341?

The only difference with the XCSE7342 is the cable entry is 20mm

What is the part code for a Harmony Stop Plug in 30mm

No longer available use 30-20mm adaptor and 20mm plug

What would be the adaptor for 25 x 16mm ducting to 20mm conduit.

The adaptor is a 900/25/16CA-WE, This suits the 25x16mm plastic mini ducting to convert to a 20mm conduit.
This only comes in white
Please see link for more conduit and mini ducting requirements.
https://updates.clipsal.com/ClipsalOnline/Files/Brochures/CMS0003.pdf

Do you have 20mm conduit clips in stainless steel?

No, unfortunately there is no stainless steel conduit clip. Only the full saddles are available in stainless steel.

For further information please visit https://www.clipsal.com/Trade

What is the part code for a latching trip wire switch with 1N/C + 1 N/O contact?

XY2CJS15H29 will suit up to 20m operating cable length.

How do we do an outside temperature sensor in CBus

You will need to use a temperature coupler in the board and a temperature probe outside. Up to 20m limit.

How to determine the firmware version of CM2000 series meters via Front Panel or remotely by software

Issue
The customer needs to determine the current firmware version of a Circuit Monitor 2000 either via front panel or over comms remotely by software.

Product line
CM2000 Series meters:
CM2050
CM2150
CM2250
CM2350
CM2450

Environment
Firmware version verification

Cause
The meter may not have the latest firmware version 17.011 (fix for rapid energy accumulation on pervious versions of firmware)

Resolution

Via Software:
If CM2000 software is connected to an Ethernet Gateway unit such as EGX or ECC, a Modbus TCP/IP program (like Modscan) or Modbus "Tester" could be used to determine the firmware version over comms.

1- Read register 2094. This register has a 4 digit number. The two digits on the right in the 4-digit decimal value represent the circuit monitor firmware version (e.g. the decimal value of register 2094 is "1617", the firmware version is 17.XXX).  
2- Then read register 2093. This decimal value represents the circuit monitor firmware sub-revision level (e.g. the decimal value of register 2093 is "9", the firmware version and sub-revision is 17.009).

To download "Tester" software, you may refer to article FA180037

Via front panel:
The version of firmware in the CM2 can be determined by using the Configuration option of the Setup Mode. The Configuration option allows the user to view configuration data in Protected Mode. No changes to CM2 configuration can be saved when in Protected Mode. When entering the Configuration option in Protected Mode, the CM2 will cycle through four screens of device information. This information will contain the firmware version currently resident in the CM2. It also contains the device model number and the last four digits of the device serial number. 

PROCEDURE: To view configuration data, complete the following steps:
1. Press the MODE button until the red LED next to [Setup] is lit. The circuit monitor displays ConFig.
2. Press the PHASE [Enter] button. The circuit monitor displays the password prompt P - - - -.
3. Enter 9999 for the password. To enter 9999, use the SELECT METER [Value] buttons to decrease the displayed value until it reaches 9999. Then press the PHASE [Enter] button. The circuit monitor enters the protected viewing mode and scrolls through the following device information:

  • d=2450 (the number after d= represents the device model number)
  • s=0345 (the numbers following s= represent the last four digits of the device serial number)
  • r=1617 (the first two digits after r= represent the reset code revision and the last two digits represent the circuit monitor firmware revision level
  • L=0009 (the digits following 1= represent the circuit monitor firmware sub-revision level, as in firmware version 17.0009)

After this scrolling sequence, the display shows the present CT ratio.

The instructions are also in the attached POWERLOGIC/POWERLINK TECH SUPPORT Application Tip document.

What is a ZCDEP20?

It is a metal 20mm cable gland entry to fit the ZCMD** limit switch body.
There is also a 16mm option ZCDEP16.

What components make up a XCKD2145P16?

 ZCD21 + ZCDEP16 + ZCE01 + ZCY45 = XCKD2145P16
The ZCDEP16 is the 16mm cable entry, the ZCDEP20 can be substituted if a 20mm cable entry is more suitable.

What would be a longer screw to suit Clipsals round j-boxes (Junction Boxes)?

The part number would be 248/20 which is a combination screw head 20MM 3/16 BSW.

what is the part number for an inspection elbow to suit 20mm HFT conduit ?

The part number is 244HF20-BK

Is the 20mm blanking plug for PDL 56E1/20/20 available as a spare part ?

The code for the threaded blanks is PDL56PLUG20GY

What is the cable entry for a LE1M35U705

2 x 13mm PG at bottom and top
2 x 20mm ISO at bottom and top
2 x 21mm PG at bottom and top
2 x 25mm ISO at bottom and top

What are the dimensions of the SC2025 behind the plate ?

The SC2025 protrudes 20mm from the rear of the plate, Allow minimum 10mm for cabling behind the plate.

What is the replacement for a XCKJ5910H7?

The replcaement for this Safety switch would be a XCSB702 which was the superceeded again by the XCSB702.
The Main difference is that the XCSB702 has a 20mm thread as apose to the half inch thread.

Can 56JB1SWA take metal glands?

56JB1SWA has 3 entries, all of which are suitable for any metal gland (especially glands for SWA cables) that have a 20mm thread.
For further information, please visit https://www.clipsal.com/Trade/Products/ProductDetail?catno=56JB1SWA

Which type of switch should be used for the RemoteTest/Hush feature on the 755PSMA2 Smoke alarm?

Any 240V momentary switch, such as a 30MBP Bell Press Switch can be wired to either of the two new mounting bases 755RB or 755RFB up to 20m away. A relay can also be pulsed on momentarily via a security or home automation panel to activate the test/hush function. 

NetBotz Fiber Pod Extender

Issue:

NetBotz Fiber Pod Extender

Product Line:

NetBotz

Environment:

NetBotz Fiber pod extender.

Cause:

Product information.

Resolution:

The NetBotz Fiber Pod Extender is composed of two main components:
  • Local Extender Unit
  • Remote Extender Unit

The Fiber Pod Extender has an integrated 4 port USB hub built into the Remote Extender Unit.

The NetBotz Fiber Pod Extenders support up to 1640 feet (500 meters) of CAT-5 cabling between the local and remote ends.




Local Extender Unit:
  • Self-powered
  • Attaches to NetBotz 420 or 500 via standard USB cable
  • Upstream = USB B connector (connects to the 420 or 500)
  • Downstream = MT-RJ connector (connects to the Remote Extender Unit)

Remote Extender Unit:
  • Self-powered
  • Integrated 1 port USB hub
  • Upstream = MT-RJ connector (connects to the Local Extender Unit)
  • Downstream = USB A connector (connects to camera or sensor pods)
  • Maximum of 1 hub can be connected to the Remote Extender Unit to extend an additional 16 feet or 5 meters.

NOTE: Both ends of the Fiber Pod Extender must be powered.

Fiber Cabling Specifications:
  • The fiber cabling must provide a duplex connection and be terminated with MT-RJ connectors at both ends.
  • To ensure proper operation, only 62.5/125 multimode or 50/125 multimode cabling should be used to connect the Local Extender Unit to the Remote Extender Unit.

What is the difference between the 56E1 and the 56E1/20/20 or the 56E1/25/25?

The entries on the three enclosures are different. The 56E1/20/20 has two 20mm entries on the top and one 25mm entry on the bottom, the 56E1/25/25 has two 25mm entries on the top and one 32mm entry on the bottom and the 56E1 has one 32mm entry on top and one 25mm entry on the bottom.
 

What is the part no for a round junction box in Brass?

Part no is BJB204 - it is 20mm with 4 entries.
this is the link https://www.clipsal.com/Trade/Products/ProductDetail?CatNo=BJB204&c=1&ms=5&mg=348&g=3485018

Or BJB254 - it is 25mm with 4 entries.
this is the link https://www.clipsal.com/Trade/Products/ProductDetail?catno=BJB254

User-added image

What is the part number for a screwed converter , to go from 3/4 inch to 20mm?

The part number for a screwed converter , to go from 3/4 inch to 20mm is - 235S3/4/20

For further information , visit link below:-
https://www.clipsal.com/Trade/search-results?q=235S3/4/20
User-added image

What are the part numbers for the Halogen free conduit j-boxes, 1 way 20mm?

The part numbers for the Halogen free conduit j-boxes, 1 way 20mm are - T240HF1L20-BK & T240HF1R20-BK

For further information visit link below:-
www.clipsal.com/Trade/search-results?q=T240HF1R20
https://www.clipsal.com/Trade/search-results?q=T240HF1L20
User-added image
User-added image

What are the part numbers for the 25mm PVC saddles and spacers?

The part numbers are 261/25 for the saddles and 261S25 for the spacers. 

Some of the key features are:
  • 63mm Length x 20mm Width x 29mm Overall Height
  • 48mm Mounting Centre
For further information please visit https://www.clipsal.com/Trade/search-results?q=261/25



 

What are the part numbers for the Power and Feedback cables for a BMH1003 xxxxxx motor ?

Issue: Part numbers

Product Line: BMH

Environment: None

Cause:

Resolution:

The part number for the power cable for a BMH1003 xxxxxx motor is VW3 M5101 Rxxx . where xxx = 15, 30, 50, 100, 150, 200, 250, 500, 750 for cable lengths 1.5m, 3m, 5m, 10m, 15m, 20m 25m 50m and 75 m respectively, The composition of this cable is [(4 x 1.5 mm^2) + (2 x 1 mm^2)] and comes with a pre-made M23 style industrial connector on the motor end and free ends on the drive side.

The part number for the feedback cable for a BMH1003 xxxxxx motor is VW3 M8102 Rxxx  where xxx = 15, 30, 50, 100, 150, 200, 250, 500, 750 for cable lengths 1.5m, 3m, 5m, 10m, 15m, 20m 25m 50m and 75 m respectively, The composition of this cable is [(3 x 2 x 0.14 mm^2) + (2 x 0.34 mm^2)] and comes with a pre-made M23 style industrial connector on the motor end and an RJ45 style connector on the drive side.
Show More