The part number for cover to suit P2031VA is - P2001
Unfortunately, we only make a 2 gang version.
Yes the part number is 2031VH-RD
No, unfortunately you will need to buy the parts separately.
Yes, one off 2031VH + one off 5031NMML
No Medilec permanent connection unit
Use 2031VH with a 38TB Mech.
Yes, The grid plate has a terminal block on the back and is rated at 30A. The part number is 2031VXCB.
Yes, one off 2034VH + one off 5031NMML + three off 5031NMS
The part code is 2000-WE surround cover plate
Part no P2031VH will fit on either 449A or 449ASD mounting block
The 2031RC series consists of 2031RC30, 2031VRC30, 2031RC10, 2031VRC10, ML2031RC10 and ML2031VRC10.
The twin brown wires power the Line Power Available LED. These wires must be connected into the Line Active and Neutral terminals with the incoming supply wires.
For further information please refer to the attached installation instruction
The part number is P2031VA.
Yes, they are the same plate size however the enterals have different dimensions ie the back of the powerpoint m protudes less than the switch etc however it is wider....
Part numbers are P2031VH (single) P2032VH (double) P30M (Mech)
No, you will have to buy the whole product 4031VH plate and grid assembly.
Part number 30PB will fit standard into 4031VH plate.
Yes, one off 2032VH + one off 5031NMML + one off 5031NMS
No, unfortunately it only has the one colour.
No, We do not supply or encourage this as the 2031v66 has a specific gasket set up to ensure weatherproof rating and this may be compromised if tampered with therefore we only sell them assembled.
Unfortunately we dont do the mech as a spare part it is essentually a 30 mech with a rubber seal between the contacts ant the dolly and we dont do that mech as a spare part.
The following parts are required to build the equivelent: 1x C2031VH + 1x 5031NMML
No. Unfortunately, part number 30M35 CANNOT be used in 2031V66.
There is No 4060 series option - use 30MD2-WE + 4031VH
Changing input plugs on Smart-UPS 2000VA or larger
Smart-UPS 2000VA or larger
All Smart-UPS 2000VA or larger have an input plug that is not a standard 5-15 household style plug.
The higher capacity of these UPS models require an input plug that is either 20amp or 30 amp (depending on model) rather than the traditional 15 amp household plug you may be more familiar with. The UL listing of the UPS assumes that the UPS is using the input plug for which it was designed. Modifying the input plug may affect the UL or other regulatory compliance. Schneider Electric does not recommend modifying the input plug of your Smart-UPS UPS or attached Smart-UPS Accesories (IE: Stepdown Transformers, PDU strips, ETC)
Note: If you decide to go against this recommendation and change the input plug of your UPS, please be aware that the functional capacity of the UPS will be limited by the input circuit.
(I E: An SMT3000 being supplied 15 amps is effectively a 1500VA UPS rather than the 3000VA that it is rated for.)
The part number for the 1 gang Iconic switch , and can the mech be rotated for horizontal or vertical switch plates - 3041VA and yes can be mounted Vertical or Horizontal..
For further information , visit link below:-
No it can not - we recommend fitting the 30USBCM to the Saturn communication wall plates eg 4031VH
No, but you can use a 4031VH and a 30MD.
Any 30 series mechanism will fit into the range of 4031vh -4036vh Saturn plates.
Any Saturn plate that accommodates 30 series mechs will be suitable
eg 4031VH to 4036VH
The part number 4062ELEDM suits Saturn 4061 plates, however
32ELEDM Ssuits 4031VH plates etc
The part number 30MD into 4031VH to 4036VH plates.
No alternative with the same style look, but it can be replaced with a different style look with the same functionality switch.
- It can be replaced with Classic C2000 Series Grid Plate and 30 Mech switches, one off C2031VH + one off 5031NMML
- It can be replaced with Slimline SC2000 Series Grid Plate and 30 Mech switches, one off SC2031VH + one off 5031NMML
Yes, as it is based on 30 series mech with 4 terminals it is 2 way compatible.
Some of the key features are:
- 1 gang weatherproof switch
- Standard size gridplate and surround complete with one 30M switch
- Vertical mount
- 116 mm Length x 76 mm Width x 30 mm Depth
- 84 mm apart Mounting centres
For further information please visit https://www.clipsal.com/Trade/Products/ProductDetail?catno=2031V66
If you want 2 stove switches in one plate, you would need to use Clipsal 4032VH and 30M35 and for the telephone use a 30BTM and 4031VH
HDMI 30 series mechanism 30HDMIS-WE can fit into the 4031VH etc of the saturn series
on page 17 of the pocket - the grid & plates fit 30 series mechanism's
There is no telephone mechanism specific for Saturn range. However the 30 series telephone mechanism 30RJ64SMT-** /30RJ66SMT will fit on the Saturn communication plates. Eg 4031VH-PW
No, a 30USBC mech will not fit a 4061VH or 4061PBL or similar plates
30USBC mechs will only fit a 4031VH or similar communication plates as 30USBC is a 30 series style of mech
No, there isn't a 3 position switch. The only way would be to use a 4031VH and a 30 Series 3 position switch.
For further information please visit https://www.clipsal.com/Trade
30RJ mechs will only fit into Saturn 4031VH to 4036VH plates, as they accommodate any 30 series mechanism.