White Electric | 2000 Series Flush Surround and Grid Plate 1 Gang

Equipotential Nodes are the same but act as a secondary or auxiliary junction.
Same product but as per regulations must be labeled as "equipotential nodes."

Please go to the website via the following link https://www.clipsal.com/products/detail?CatNo=E35/2&tab-document-1=0&itemno=E35/2
https://www.clipsal.com/products/detail?catno=ML2031R01&tab-document-1=0&itemno=ML2031R01-WE

The part number of the stud bracket to suit large format Prestige plates is 156/2. It will suit all large format sized Prestige plates,  i.e. P2031/2VA, P2032/2VA, P2033/2VA, P2034/2VA, P2015X, P2015XX, P2015/2, P2015/2/15, P2025/2, P2025/2N, P2025/2/15.
For further information please refer to the below link:
https://www.clipsal.com/Trade/Products/ProductDetail?catno=156/2

 

The part number for the switch is a - C2031V66 & C2032V66.
C2031V66

Please go to the following links below and check under the Documentation Tab for more information.

Australia - https://www.clipsal.com/products/detail?CatNo=C2031V66&itemno=C2031V66-WE&backto=/search?q=C2031V66&tab-document-1=0
New Zealand - https://www.pdl.co.nz/products/detail?CatNo=C2031V66&itemno=C2031V66-WE&backto=/search?q=C2031V66&tab-document-1=0

C2032V66

Please go to the following links below and check under the Documentation Tab for more information.

Australia - https://www.clipsal.com/products/detail?CatNo=C2032V66&itemno=C2032V66-WE&backto=/search?q=C2032V66&tab-document-1=0
New Zealand - https://www.pdl.co.nz/products/detail?CatNo=C2032V66&itemno=C2032V66-WE&backto=/search?q=C2032V66&tab-document-1=0

Yes - it is a special MTO product similar to a ML2031E08 and will need to be priced through our Quotes/ Commercial operations  department.

For more information on our Medilec range please visit the Clipsal Web site on the link supplied https://www.clipsal.com/search?q=ml2031e08

The built in push button on the 31VETR3 or 2031VETR3 has the following functions:
• Pressing the button when the timer is passive will initiate timing and set the load, and indicator, to the active state according to the configuration switch settings.
• Pressing the button during timing will cancel timing and set the load, and indicator, to the passive state according to the configuration switch settings.
• To restart the timer when the load is already on, simply perform consecutive turn-on and turn-off functions.
For further information, please refer to the below link:
https://www.clipsal.com/Trade/Products/ProductDetail?catno=31VETR3
https://www.clipsal.com/Trade/Products/ProductDetail?catno=2031VETR3
https://download.schneider-electric.com/files?p_Doc_Ref=CLPDOC_W0001273&p_File_Ext=.PDF

The recommended steps are:

1. Detach the top of the smoke alarm from its base, remove the battery and hold the ‘test’ button until the alarm is no longer beeping. This completely discharges the smoke alarm for a guaranteed reset.
2. Vacuum the vents.
3. Spray bug surface repellent on a rag then wipe over the unit and surrounding ceiling.
4. Hold the test button for 20 seconds which will reset the unit.
5. If the above fails and it is within the warranty period, you can replace the unit by lodging a warranty form via clipsal.com/warranty (Note: If it is out of warranty, you will need to pay to replace it.)

Remember smoke alarms are there for a reason, so ensure you’re safe at all times.