Flush SurRound, 1 Gang, Horizontal Mount, Curved Sided, Standard Pattern

The part #'s for the Panelmate Plus Modbus Plus Interface Boards are:
1) MM-PMMP001C - Panelmate Plus 2000 / 3000 / 4000 Modbus Plus Interface, CE
2) MM-PMMP002C - Panelmate Plus 2000 / 3000 / 4000, Dual MB+ Interface, CE
3) MM-PMMP003C - Panelmate Plus 1000 / 1500 Modbus Plus Interface, CE

The buzzer frequency is between 2000Hz and 2600 Hz. (2300Hz typical)

ENS 6.4 is only supported with SQL 2005 and SQL 2008 instances.
During the install, SQL 2000 instances can be chosen, but the install will not complete if a SQL 2000 instance is selected.

Product Lines
CM4000 / CM4
CM3000 / CM3
CM2000 / CM2
PM800 / PM8
PM700 / PM7
PM600 / PM6
PM200 / PM2
EM3500
PM5000 Series
PM8000

Environment
On-board Password

Resolution
The default password is 0000

ION Enterprise 3.0 MSDE 1.0 (SQL Server 7.0)
ION Enterprise 4.0 MSDE 1.0 (SQL Server 7.0)

ION Enterprise 4.5 MSDE 1.0 (SQL Server 7.0)

ION Enterprise 5.0 MSDE 2000 (SQL Server 2000)

ION Enterprise 5.5 MSDE 2000 (SQL Server 2000)

NOTE: It is possible to use ION Enterprise 5.5 Service Pack 2 with SQL Server 2005, but some modifications are required. See KB articles 12704, 12708 and 12823 for detailed information.

ION Enterprise 5.6 SQL 2005 Express (SQL Server 2005)
NOTE: ION Enterprise 5.6 will use an existing MSDE 2000 instance, but will install SQL Express on new systems if there is no pre-existing SQL Server instance.
ION Enterprise 6.0 SQL 2005 Express with Reporting Services SP3 (SQL Server 2005 SP3 with Reporting Services)
NOTES: The ION Enterprise 6.0 installer will upgrade an existing MSDE 2000 instance to SQL Server 2005 Express with Reporting Services. ION Enterprise 6.0 does not support SQL Server 2000. It also does not support SQL Server 2008

• 

  Original article#16492

  Public

  All content © 1992-2009 Schneider Electric

Microsoft (MS) Office XP or 2000 are older versions of the MS Office suite. The Commissioning Guide for ION Enterprise recommends Excel 2003 as a minimum version and the earlier versions have not been tested by the Software department, however, there are customers who have successfully installed MS Office 2000 and ION Enterprise 5.6 together. If there are any problems using an older version of Office, the resolution is to upgrade to Office 2003.

Last Revised: November 22, 2007
Applies To: ION Enterprise 5.6
Public
All content © 1992-2007 Schneider Electric

Goals and Symptoms

With Power Suite V1.5, I understand that the PS for Pocket PC can be installed for iPAQ 3800/3900. What about the newer series of iPAQs (eg 2200 and 5500)? Does the PS support this product series? Does it also work with Pocket PC 2003? Thank you.

Causes and Fixes

Powersuite v1.5 doesn't work under PC2003, for that you need to wait the V2 of Powersuite ( forecast end 2003 ) with Ipaq22xx in qualification.

This article applies to SQL 2000 and SQL 2005 only.

To check you SQL server version and edition, run the following query on the SQL instance:

SELECT SERVERPROPERTY('productversion'), SERVERPROPERTY('productlevel'), SERVERPROPERTY('edition')



The results are:
- The product version (for example, 8.00.534).
- The product level (for example, "RTM" or "SP2").
- The edition (for example, "Standard Edition"). For example, the result looks similar to: "8.00.534 RTM Standard Edition"

Use the following table to identify your version:

• Release	Sqlservr.exe
  SQL Server 2000 RTM	2000.80.194.0
  SQL Server 2000 SP1	2000.80.384.0
  SQL Server 2000 SP2	2000.80.534.0
  SQL Server 2000 SP3	2000.80.760.0
  SQL Server 2000 SP3a	2000.80.760.0
  SQL Server 2000 SP4	2000.8.00.2039
  SQL Server 2005 RTM	2005.90.1399
  SQL Server 2005 Service Pack 1	2005.90.2047
  SQL Server 2005 Service Pack 2	2005.90.3042

Certain alarms on the circuit monitor allow the user to configure the pickup and dropout setpoints in either absolute or relative mode. In absolute mode, the user enters the absolute values on which to alarm. In relative mode, the setpoints reflect a percentage of the running average of a particular value. The purpose of this knowledge base article is to describe the proper configuration of relative setpoints for the different models of circuit monitor.
Circuit Monitor 2000 Series (CM2000 or CM2):
On the CM2000, relative setpoints should be configured as the percentage of the offset from normal operation on which the user wants to alarm. In other words, the setpoints are configured from a reference of 0%. Most simply put, if the user wants to alarm when a value is 5% over the recent running average, he should enter a setpoint of 5%.

Circuit Monitor 3000 Series (CM3000 or CM3) & Circuit Monitor 4000 Series (CM4000 or CM4):
For the CM3000 and CM4000, relative setpoints are configured from a reference of 100%. Most simply put, if the user wants to alarm when a value is 5% over the recent running average, he should enter a setpoint of 105%.

*Note: Whenever possible, absolute alarm setpoints are recommended to ensure the most predictable and reliable alarming performance from the circuit monitor.