Quantcast

Cable Management Fixing Accessories, 40mm Zinc Plated Metal Half Saddle

Cable Management Fixing Accessories, 40mm Zinc Plated Metal Half Saddle

Cable Management Fixing Accessories, 40mm Zinc Plated Metal Half Saddle

Item Number: 180/40

Retail
$2.50
RRP (Inc. GST)

Datasheet

Barcode

Qty UoM EAN Colour
-
-
-

Specifications

Design

Product brand

Clipsal

Surface treatment

zinc plated

Sustainable offer status

Green Premium product

Physical

Length

74 mm

Width

32 mm

Height

41 mm

REACh Regulation

Free of Substances of Very High Concern above the threshold

REACh free of SVHC

Yes

EU RoHS Directive

Pro-active compliance (Product out of EU RoHS legal scope)

Toxic heavy metal free

Yes

Mercury free

Yes

RoHS exemption information

Yes

China RoHS Regulation

 Pro-active China RoHS declaration (out of China RoHS legal scope)

Environmental Disclosure

ENVPEP110719EN

Material

Material

steel

Others

Package 1 Height

38 mm

Package 1 Length

75 mm

Package 1 width

32 mm

Diameter

40 mm

Package 1 Weight

37 g
Show all specifications

Frequently Asked Questions

hide show

Are the Clipsal Conduit Clips available in Electric Orange?

No, they are only available in grey.

This applies to the 280/16 (16mm), 280/20 (20mm), 280/25 (25mm), 280/32 (32mm), 280/40 (40mm) and 280/50 (50mm).

Trace SW4024 shows error under/over speed as yes, what does that mean?

TRACE SW4024 shows Generator under/over speed error



 The Trace SW4024 120/60hz has a preset AC2 allowable frequency range from (53-67 hz)
If there is a frequency out of that range you will get a generator under/over frequency.
Solution: Service generator, replace bushings if applicable, and try to reduce max charge rate to see if the remedies the generator input. 
 

Typical 3-line drawings for Sepam Series 20, 40 and 80 current and voltage input connections

Issue
Need drawings of Sepam 20/40 Feeder, Sepam 20/40 Main and Sepam 80 Main/Feeder.

Product Line                 
Sepam 20 Series
Sepam 40 Series
Sepam 80 Series

Resolution
See attachment for drawings.
 

Conext SW - Installation/ Wiring issue.

Issue:

Customer is installing the Conext SW and wants to confirm the wiring of the AC and DC cabling. 

Environment:

Conext SW 2524 120/240 Split-phase (865-2524)
 
Conext SW 4024 120/240 Split-phase (865-4024)


Resolution:
 

See the attached wiring diagrams for the Conext SW and Conext SW-NA.
Do not mix AC and DC wiring in the same conduit or panel. Consult the applicable installation code for details.
There are two dual 3/4" /1" trade-size knockouts on the side panel and another two on the bottom panel for AC wiring. Use the same trade size of strain relief as the trade size of the knockout(s) you are using.

 

CCT640 Connector for VT Voltage Sensor Installation Sheet, Instruction Bulletin (ANSI), 63230-216-250A1, May 2007

Issue
Sepam relays can connect to any standard voltage transformer (VT) with a rated secondary voltage of 100240 V. Square D offers a wide range of voltage transformers:
to measure phase-to-neutral voltages: VT with 1 insulated MV terminal
to measure phase-to-phase voltages: VT with 2 insulated MV terminals
with or without integrated protection fuses
The CCT640 connects the four additional voltages available in Sepam B83. It provides impedance matching and isolation between the voltage transformers and the input circuits of the Sepam relay. The connection port (B2) is not visible in Figure 1, behind the CCT640.



see attachment:

63230-216-250_CCT640_InstallSheet.pdf



 

In programming PID, what does parameter FbS do on an ATV312 drive?

Issue:
Parameter FbS (feedback scale factor)

Product Line:
ATV31 and ATV312

Environment:
All models and serial numbers

Cause:
None

Resolution:
The parameter FbS is a parameter that can be used to scale the reference according to the range of the feedback sensor.
Example: Regulating pressure
PI reference range of process, 0-50 psi (0-100%)
Range of pressure sensor, 0-100 psi
FbS = Max sensor range / Max process range
FbS = 100/50 = 2
Show More