clip conduit 40mm / 1.1/2in.

Cable Management Fixing Accessories, 40Mm Zinc Plated Metal Half Saddle

Catalogue Number: 180/40
clip conduit 40mm / 1.1/2in.
Colour:
Colour: Per UOM Std.
  • 1 PCE

Specifications

hide show
Product brand
Clipsal
Diameter
40 mm
Material
steel
Surface treatment
zinc plated
Length
74 mm
Width
32 mm
Height
41 mm
REACh Regulation
Free of Substances of Very High Concern above the threshold
REACh free of SVHC
Yes
EU RoHS Directive
Pro-active compliance (Product out of EU RoHS legal scope)
Toxic heavy metal free
Yes
Mercury free
Yes
RoHS exemption information
Yes
China RoHS Regulation
 Pro-active China RoHS declaration (out of China RoHS legal scope)
Circularity Profile
N/A

Documents & downloads

hide show
Filter items
  • All

  • Product Brochures

  • Technical Data Catalogues

  • Installation Instruction

  • Specifications

  • Certificates (MSDS)

Frequently Asked Questions

hide show

Are the Clipsal Conduit Clips available in Electric Orange?

No, they are only available in grey.

This applies to the 280/16 (16mm), 280/20 (20mm), 280/25 (25mm), 280/32 (32mm), 280/40 (40mm) and 280/50 (50mm).

Trace SW4024 shows error under/over speed as yes, what does that mean?

TRACE SW4024 shows Generator under/over speed error



 The Trace SW4024 120/60hz has a preset AC2 allowable frequency range from (53-67 hz)
If there is a frequency out of that range you will get a generator under/over frequency.
Solution: Service generator, replace bushings if applicable, and try to reduce max charge rate to see if the remedies the generator input. 
 

Conext SW - Installation/ Wiring issue.

Issue:

Customer is installing the Conext SW and wants to confirm the wiring of the AC and DC cabling. 

Environment:

Conext SW 2524 120/240 Split-phase (865-2524)
 
Conext SW 4024 120/240 Split-phase (865-4024)


Resolution:
 

See the attached wiring diagrams for the Conext SW and Conext SW-NA.
Do not mix AC and DC wiring in the same conduit or panel. Consult the applicable installation code for details.
There are two dual 3/4" /1" trade-size knockouts on the side panel and another two on the bottom panel for AC wiring. Use the same trade size of strain relief as the trade size of the knockout(s) you are using.

 

What's the difference between the SyMax Model 50 programmable controllers 8005CP50 and 8005CP51?

The difference between the two SyMax Model 50 programmable controllers is the power voltage rating.
8005CP50 is a 120/240 VAC Processor Unit.
8005CP51 is a 24 VDC Processor Unit.


Legacy KB System (APS) Data: RESL169642 V1.0, Originally authored by on , Last Edited by on
Related ranges: Sy/Max

Typical 3-line drawings for Sepam Series 20, 40 and 80 current and voltage input connections

Goals and Symptoms

Typical 3-line drawings of Sepam 20/40 Feeder, Sepam 20/40 Main and Sepam 80 Main/Feeder.

Causes and Fixes

See attachment
Sepam.zip



AEDL3
Legacy KB System (APS) Data: RESL203669 V1.0, Originally authored by MiZe on 10/09/2010, Last Edited by MiZe on 10/09/2010
Related ranges: Sepam series 80, Sepam series 40, Sepam series 20

In programming PID, what does parameter FbS do on an ATV312 drive?

Issue:
Parameter FbS (feedback scale factor)

Product Line:
ATV31 and ATV312

Environment:
All models and serial numbers

Cause:
None

Resolution:
The parameter FbS is a parameter that can be used to scale the reference according to the range of the feedback sensor.
Example: Regulating pressure
PI reference range of process, 0-50 psi (0-100%)
Range of pressure sensor, 0-100 psi
FbS = Max sensor range / Max process range
FbS = 100/50 = 2

How SCADAPack VISION 10/60 can go from last to first screen?

Configure NEXT/F1 key as shown in the attachment. When NEXT/F1 key is pressed then the first screen will be displayed.
 

CCT640 Connector for VT Voltage Sensor Installation Sheet, Instruction Bulletin (ANSI), 63230-216-250A1, May 2007

Sepam relays can connect to any standard voltage transformer (VT) with a rated secondary voltage of 100240 V. Square D offers a wide range of voltage transformers:
to measure phase-to-neutral voltages: VT with 1 insulated MV terminal
to measure phase-to-phase voltages: VT with 2 insulated MV terminals
with or without integrated protection fuses
The CCT640 connects the four additional voltages available in Sepam B83. It provides impedance matching and isolation between the voltage transformers and the input circuits of the Sepam relay. The connection port (B2) is not visible in Figure 1, behind the CCT640.



see attachment:

63230-216-250_CCT640_InstallSheet.pdf


AEDL3

Keywords:
63230216250

 


  • Date Created: February 26, 2008
    Last Revised: February 26, 2008
    Public
    Original Author: JJ
    All content © 1992-2008 Schneider Electric

Legacy KB System (APS) Data: RESL191278 V1.0, Originally authored by PhHa on 02/27/2008, Last Edited by PhHa on 02/27/2008
Related ranges: Sepam series 80, Sepam series 20, Sepam accessories

Customer is looking for a sizing tool for Schneider Electric solar products.

Customers are looking for a sizing tool for there solar projects or installations with Schneider Electric products. 

We can provide the customer with a Conext Designer tool which includes the following products:

Conext TX inverters
Conext Core XC
Conext TL
Conext RL
Conext CL
XW-MPPT 80/60

Download link for the Conext Designer:
https://schneider-electric.box.com/s/g5yyi93prdtogi877yu2




 

Energy Meter shows "Phase Loss" Alarm

Issue
Energy meter shows “Phase Loss” alarm on front display.

Product Line
Energy meter (EMB and EME series).

Environment
Installing/wiring energy meter

Cause
If the voltage of any phase is measured as less than 75% of the voltage on any other phase, the display will show PHASE LOSS and indicate the specific phase(s).

Resolution
If the energy meter is installed with the proper number of phases (see selection below to determine this) then the phase voltages should be verified. If the number of phases installed is not correct, then the phase loss alarm will be indicated in all operating conditions.

It’s very important to know the model number of your Energy meter.  
For example, users see “Phase Loss” error when they use EMB2043 (1 phase, 3 wire) with 1 phase, 2 wire application.

As a result, it’s very important for users to know their application and use appropriate meter that meets their system type.  Please review the tables below for selecting correct meter.

Basic 120/240 Volt 208 Wye

EMB1010 Basic 100A 1 Phase, 2 wire installation 1 CT
EMB1021 Basic 200A 1 Phase, 2 wire installation 1 CT
EMB1032 Basic 300A 1 Phase, 2 wire installation 1 CT
EMB2010 Basic 100A 1 Phase, 3 wire installation 2 CTs
EMB2021 Basic 200A 1 Phase, 3 wire installation 2 CTs
EMB2032 Basic 300A 1 Phase, 3 wire installation 2 CTs
EMB2043 Basic 400A 1 Phase, 3 wire installation 2 CTs
EMB2083 Basic 800A 1 Phase, 3 wire installation 2 CTs
EMB3010 Basic 100A 3 Phase, 4 wire installation 3 CTs
EMB3021 Basic 200A 3 Phase, 4 wire installation 3 CTs
EMB3032 Basic 300A 3 Phase, 4 wire installation 3 CTs
EMB3043 Basic 400A 3 Phase, 4 wire installation 3 CTs
EMB3083 Basic 800A 3 Phase, 4 wire installation 3 CTs
EMB3084 Basic 800A 3 Phase, 4 wire installation 3 CTs
EMB3164 Basic 1600A 3 Phase, 4 wire installation 3 CTs


Extended Range 120/480 Volt Wye

EME1010 Basic 100A 1 Phase, 2 wire installation 1 CT
EME1021 Basic 200A 1 Phase, 2 wire installation 1 CT
EME1032 Basic 300A 1 Phase, 2 wire installation 1 CT
EME2010 Basic 100A 1 Phase, 3 wire installation 2 CTs
EME2021 Basic 200A 1 Phase, 3 wire installation 2 CTs
EME2032 Basic 300A 1 Phase, 3 wire installation 2 CTs
EME2043 Basic 400A 1 Phase, 3 wire installation 2 CTs
EME2083 Basic 800A 1 Phase, 3 wire installation 2 CTs
EME3010 Basic 100A 3 Phase, 4 wire installation 3 CTs
EME3021 Basic 200A 3 Phase, 4 wire installation 3 CTs
EME3032 Basic 300A 3 Phase, 4 wire installation 3 CTs
EME3043 Basic 400A 3 Phase, 4 wire installation 3 CTs
EME3083 Basic 800A 3 Phase, 4 wire installation 3 CTs
EME3084 Basic 800A 3 Phase, 4 wire installation 3 CTs
EME3164 Basic 1600A 3 Phase, 4 wire installation 3 CTs


NOTE: the meter will operate, however the phase loss alarm will constantly be present if the improper meter is in use.

Common mode filter for bearing current reductions for the ATV600 and ATV900 drives frame size four drives?

Issue:
Common mode filter for bearing current reductions for the ATV600 and ATV900 drives frame size four drives?

Product Line:
ATV600 and ATV900 drives frame size 6

Environment:
All 

Cause:
Filter for bearing current reductions

Resolution:
The part number is VW3A5504 and its value of inductance is 180.0 uH

What is the replacement AC coil for CAD32 and CAD50 relay?

Issue:
Are replacement  AC coil available for CAD32 and CAD50 relay?

Product Line:
Tesys Relays

Environment:
All Products

Cause:
Product selection

Resolution:
Volt = coil part number
12 = LXD1J7
21 = LXD1Z7
24 = LXD1B7
32 = LXD1C7
36 = LXD1CC7
42 = LXD1D7
48 = LXD1E7
60 = LXD1EE7
100 = LXD1K7
110 = LXD1F7
115 = LXD1FE7
120 = LXD1G7
127 = LXD1FC7
200 = LXD1L7
208 = LXD1LL7
220/230 = LXD1M7
230 595 21 LXD1P7
230/240 = LXD1U7
277 781 30 LXD1W7
380/400 = LXD1Q7
400 = LXD1V7
415 = LXD1N7
440 = LXD1R7
480 = LXD1T7
600 = LXD1X7
690 = LXD1Y7

 

XW Won't qualify generator.

Issue:

XW inverter charger will not qualify AC generator. AC IN light blinks
AC input qualification, overloading the generator, unable to sustain battery charging and and running loads (multi-tasking)


Environment:

XW 4024/4548/6048 with AC generator


Resolution:

1) Ensure generator is split phase 120/240, not 120 monophase or 120/208V. Voltage from (L1 to N) and (N to L2) should add up exactly to (L1 to L2) voltage
3) Recommended, size your generator 2 times the rating of the XW system.
2) Ensure no neutral to ground bond in Generator
3) Connect gen output to AC2, not AC1 and open up AC2 parameters in XW advanced settings - ac settings menu
4) Reduce max charge rate in XW
5) If Kohler RES series generator, see  Solution 1179

Cause:

1) XW can only connect to splt-ph 120/240 unless converted to monophase 
2) Potential ground loop
3) AC2 qualification parameter window much wider than AC1
4) Gen being overloaded by combination of house loads and XW charger.

Can a circuit breaker be operated at a voltage less than the voltage marked on the breaker?

Inquiry:
Is it OK to apply a circuit breaker on a voltage system rated lower than the rating of the breaker?

Product Line:
MCB and MCCB circuit breakers

Cause:
Circuit breakers are typically marked only with a few standard voltages, while other voltage systems exist.

Resolution:
Yes. According to 2011 NEC article  240.83(E), a circuit breaker may be used at voltages equal to or less than its voltage rating. 
When applied on a system of lower voltage than marked, he interrupting rating is equal to the next highest marked interrupting rating. 
The only exceptions to application at less than rated voltage are:
1. QO and HOM -GFI, -EPD, -AFI, -CAFI, and DF circuit breakers must be applied on 120/240 Vac systems only (they need over 100 Vac to power the electronic modules)
2. EHB-EPD and EDB-EPD type breakers which must be applied on 480Y/277 systems only

NOTE:  Circuit breakers marked with DC ratings only are not suitable for application on AC systems, and circuit breakers marked with AC ratings only are not suitable for application on DC systems.

How do I hardwire 10kva and 20kva transformers in a 208/120 or 240/120 environment

Issue:
Implementing a hardwire stepdown transformer in a 208v or 240v environment


Product Line:

Smart-UPS / Symmetra

Environment:

APTF10KT01, APTF10KW01, and APTF20KW01, All Serial Numbers

Cause:

Unbalanced UPS outputs require a stepdown transformer to power 120v loads


Resolution:

This document refers to installing  the APTF10KT01, APTF10KW01, and APTF20KW01 transformers in a North American 120/240 or 120/208 environment. For installations in other regions please consult the users manual.

The wiring block outputs are as follows:


For domestic use, make sure that the Terminal Block Jumper is installed between the Ground Terminal and Terminal 8 on the output wiring block, as illustrated on page 8 of the user manual. Please also make sure that the input voltage switch is in the correct position.

The step-down transformer provides 240/120 output as 2 120v hots, a neutral, and a ground. It provides 208v output as a 120v hot, an 88v hot, and a ground. The 120v hot (terminal  7) and the 88v hot (terminal 9) are 180 degrees out of phase. You will measure 208v from terminals 7 to 9. The step-down transformer is not able to provide 2 120v hots that are 120 degrees out of phase as you would see with utility power.



 Note: If your installation requires both 208v and 120v output power you will need 2 separate subpanels: a 240v/120v panel and a dedicated 208v subpanel.

Lost Neutral - effects on loads and UL1449

Issue:

Lost Neutral - effects on loads and UL1449

Product Line:

All Back-UPS, Back-UPS PRO and Personal Surge

Environment:

Lost Neutral in electrical infrastructure.

Cause:

Lifted neutral at utility panel.

Resolution:

In a typical balanced load with all loads using the neutral return and the neutral is severed, the voltage from each Phase appears across each load and is added on itself. This is a typical fault condition. Underwriter's Laboratories realized that this fault condition is common and it is not up to the Surge Protection Industry to prevent these failures but in the event of this common failure, UL addressed this condition by requiring all Surge Protectors to pass a fault of 240 VAC at different current levels to simulate different loads. These currents are: 125 mA rms. 500 mA rms. 2.5 A rms. and 5 A rms. They also require an unlimited current test (1000 A rms. or greater). 240 VAC is used because most household wiring is 120/240 3 wire single phase and a lost neutral produces 240 VAC. The unit during this test has cheesecloth wrapped around it. The unit may not emit flame nor can it char the cheesecloth nor can it create an opening in the housing that exposes live metal parts large enough for a child's finger to be inserted. After the test, the unit may not allow leakage currents of > 0.5 mA from Line to Ground and Neutral to Ground also it must withstand a dielectric voltage of 240 VAC for minute between each protected mode. Our units have passed this stringent test requirement in order to get UL recognition and to insure the safety of our customer's lives and property.
 

The Replace Battery Date on my new SMT series Smart-UPS is incorrect.

Issue:

The Replace Battery Date indicated on the LCD screen of my new SMT series Smart-UPS is incorrect.


Product Line:

Smart-UPS

Environment:

Models beginning with SMT , All Serial Numbers

Cause:

The "Replace Battery by" field indicates an estimated date when the UPS Battery may need to be replaced. This field is dynamic  and changes depending on the operating environment of the UPS. It is not a definitive indicator of a bad battery, but it does give the customer some guidance of when to expect a need for replacement.

This field defaults to 4.5 years from the time of the last battery replacement. Occasionally you may find that on a new SMT series UPS the "Replace Battery By" date indicated on the LCD is far into the future, and therefore incorrect. 


Resolution:

To correct this issue select “Reset to Factory Defaults” from the “Configuration” menu of the LCD screen on the front of the UPS
You will need to wait approximately 30 seconds until this process complete. The LCD  will indicate "Resetting to Fact Defaults" during this process.
Upon completion, the UPS will start the new unit install wizard on the LCD screen and prompt you to set "Language", "Local Power Quality", "Menu Type", and "Audible Alarms".
Once you have made your selections, manually select “Install New Battery” from the configuration menu on the LCD.
This UPS will now properly calculate the Replace Battery Date (which will initially be  4.5 years in the future).
 

Can a 3-pole breaker be used in a 2-pole application?

Issue:
Can a three pole breaker be used in either a two pole or a single phase application?

Product Line:
MCCB

Environment:
Powerpact and Masterpact

Resolution:
  • A 3p breaker can be used on a 3 phase system using either 2 or 3 poles.
  • A 3p breaker can be used on a 1 phase system only if indicated by the markings as noted below.
For reference:
  • Per NEC article 240.85: "A circuit breaker with a straight voltage rating, such as 240V or 480V, shall be permitted to be applied in a circuit in which the nominal voltage between any two conductors does not exceed the circuit breaker’s voltage rating."
  • According to UL's White book, "3–pole circuit breakers are suitable for use on 3-phase systems only, unless marked to indicate use on 1-phase systems, such as, “For 1–phase connections, use two outside poles,” or an equivalent statement. A 3-pole breaker used in place of a 2-pole breaker on a 3-phase system, such as a 2-pole breaker used in a branch circuit that is actually two legs of a 3-phase system, is acceptable without the 3-pole breaker being specifically marked."

Powerpact P
  • The 3-pole P-frame breaker has a marking on the cover that states "single phase any 2 poles". Therefore on a 120/240Vac system, it is ok to use any 2 poles of a 3 pole P-frame breaker.
  • This breaker marking correlates with the wiring diagram markings of the M and P breaker enclosure, which shows both 2p and 3p applications.
Powerpact L
  • The 3-pole L-frame breaker does NOT have a marking for single phase systems. Therefore on the 120/240Vac system, it is NOT ok to use a 3 pole L-frame breaker.
  • This marking correlates with the wiring diagram of the L breaker enclosure, which shows only 3p applications.
Powerpact H and J
  • Three-pole Powerpact H and J-frame thermal-magnetic breakers are marked for single phase use
  • Three-pole Powerpact H and J-frame Micrologic breakers with standard trip units (U31X and U33X) are marked for single-phase use
  • Three-pole Powerpact H and J-frame Micrologic breakers with Ammeter and Energy trip units (U43X, U44X, U53X and U54X) are NOT marked for single-phase use.