Zinc Plated Metal Half Saddle 20mm

Zinc Plated Metal Half Saddle 20mm

Zinc Plated Metal Half Saddle 20mm

Item Number: 180/20

Retail
$0.58
RRP (Inc. GST)

Datasheet

Barcode

Qty UoM EAN Colour
-
-
-

Specifications

Design

Product brand

Clipsal

Surface treatment

zinc plated

Physical

Length

50 mm

Width

19 mm

Height

22 mm

EU RoHS Directive

Pro-active compliance (Product out of EU RoHS legal scope)

Material

Material

steel

Others

Diameter

20 mm

Package 1 Weight

13 g

Package 1 Height

23 mm

Package 1 width

25 mm

Package 1 Length

54 mm
Show all specifications

Frequently Asked Questions

hide show

Are the Clipsal Conduit Clips available in Electric Orange?

No, they are only available in grey.

This applies to the 280/16 (16mm), 280/20 (20mm), 280/25 (25mm), 280/32 (32mm), 280/40 (40mm) and 280/50 (50mm).

Can I order the 220/20 in white?

Yes, you can order the 220/20 in white but it needs to be done as a special.
For more information, please refer to the link:https://www.clipsal.com/Trade/Products/ProductDetail?catno=220/20

Do you have a screw cap for the 56 series plugs and extension sockets?

Yes, there is a range of screw caps to suit 56 series plugs and extension sockets.

They are 56PC for 3PH 10/20A plugs, 56PCI for 3PH 32-50A plugs ,56PC2 for single phase 10/20A plugs and 56SC2 for single phase extension sockets.

For further information please visit https://www.clipsal.com/Trade/search-results?q=56pc or https://www.clipsal.com/Trade/search-results?q=56pc2
             
 

What would be the part number for an Earth Clip, 16/20 mm.

203M.
Pressed Metal Conduit Fittings, Earth Clips, Water pipe adjustable earth clip 15 - 20mm or 1/2 - 3/4 inch.
Please see following link under the documentation tab for full catalogue.
https://www.clipsal.com/Trade/Products/ProductDetail?catno=203M

Trace SW4024 shows error under/over speed as yes, what does that mean?

TRACE SW4024 shows Generator under/over speed error



 The Trace SW4024 120/60hz has a preset AC2 allowable frequency range from (53-67 hz)
If there is a frequency out of that range you will get a generator under/over frequency.
Solution: Service generator, replace bushings if applicable, and try to reduce max charge rate to see if the remedies the generator input. 
 

How do I hardwire 10kva and 20kva transformers in a 208/120 or 240/120 environment

Issue:
Implementing a hardwire stepdown transformer in a 208v or 240v environment


Product Line:

Smart-UPS / Symmetra

Environment:

APTF10KT01, APTF10KW01, and APTF20KW01, All Serial Numbers

Cause:

Unbalanced UPS outputs require a stepdown transformer to power 120v loads


Resolution:

This document refers to installing  the APTF10KT01, APTF10KW01, and APTF20KW01 transformers in a North American 120/240 or 120/208 environment. For installations in other regions please consult the users manual.

The wiring block outputs are as follows:


For domestic use, make sure that the Terminal Block Jumper is installed between the Ground Terminal and Terminal 8 on the output wiring block, as illustrated on page 8 of the user manual. Please also make sure that the input voltage switch is in the correct position.

The step-down transformer provides 240/120 output as 2 120v hots, a neutral, and a ground. It provides 208v output as a 120v hot, an 88v hot, and a ground. The 120v hot (terminal  7) and the 88v hot (terminal 9) are 180 degrees out of phase. You will measure 208v from terminals 7 to 9. The step-down transformer is not able to provide 2 120v hots that are 120 degrees out of phase as you would see with utility power.



 Note: If your installation requires both 208v and 120v output power you will need 2 separate subpanels: a 240v/120v panel and a dedicated 208v subpanel.

Conext SW - Installation/ Wiring issue.

Issue:

Customer is installing the Conext SW and wants to confirm the wiring of the AC and DC cabling. 

Environment:

Conext SW 2524 120/240 Split-phase (865-2524)
 
Conext SW 4024 120/240 Split-phase (865-4024)


Resolution:
 

See the attached wiring diagrams for the Conext SW and Conext SW-NA.
Do not mix AC and DC wiring in the same conduit or panel. Consult the applicable installation code for details.
There are two dual 3/4" /1" trade-size knockouts on the side panel and another two on the bottom panel for AC wiring. Use the same trade size of strain relief as the trade size of the knockout(s) you are using.

 

What's the difference between the SyMax Model 50 programmable controllers 8005CP50 and 8005CP51?

The difference between the two SyMax Model 50 programmable controllers is the power voltage rating.
8005CP50 is a 120/240 VAC Processor Unit.
8005CP51 is a 24 VDC Processor Unit.


Legacy KB System (APS) Data: RESL169642 V1.0, Originally authored by on , Last Edited by on
Related ranges: Sy/Max

What is the accuracy of the Premium PLC CPU real time clock.

Real time clock accuracy:

Accuracy of the real time clock is one second (%SW50) +/- 200ms.

Resolution of the real time clock is one second (%SW50) +/- 200ms,because 200ms is the refresh rate of the RTC.
 
Accuracy error:
 
The accuracy error of the quartz oscillator is:
 
1. At 0 and 70°C : -101/20 ppm, error in second/day is -8.7/1.7, in minute/year is -53/11.
 
2. At 25°C: -20/20 ppm, error in second/day is -1.7/1.7, in minute/year is -11/11.

In programming PID, what does parameter FbS do on an ATV312 drive?

Issue:
Parameter FbS (feedback scale factor)

Product Line:
ATV31 and ATV312

Environment:
All models and serial numbers

Cause:
None

Resolution:
The parameter FbS is a parameter that can be used to scale the reference according to the range of the feedback sensor.
Example: Regulating pressure
PI reference range of process, 0-50 psi (0-100%)
Range of pressure sensor, 0-100 psi
FbS = Max sensor range / Max process range
FbS = 100/50 = 2

How SCADAPack VISION 10/60 can go from last to first screen?

Configure NEXT/F1 key as shown in the attachment. When NEXT/F1 key is pressed then the first screen will be displayed.
 

Can the PowerLogic Energy Meter be used to monitor multiple loads?

Issue
A user would like to totalize multiple loads with an Energy meter.

Product Line
Powerlogic Energy Meter

Environment
Energy Meter Installation

Cause
The installation guide for the Energy meter does not contain instructions on wiring the meter to monitor multiple loads.

Resolution
*Warning: Installation and maintenance of this device should only be performed by qualified, competent personnel that have appropriate training and experience with high voltage and current devices. Failure to follow the instructions / warnings in the Meter Installation Guide can result in permanent damage to the meter, severe injury or death. 

The Energy meter is calibrated with the set of CTs that are included with the meter, however the Energy Meter can be installed with up to three sets of parallel CTs to monitor multiple loads. When wiring multiple current transformers in parallel to the Energy Meter, all voltages corresponding to the individual loads must be the same voltage values and must be from the same source. The voltage applied to the inputs of the Energy Meter will be used in the power calculations. Monitoring different voltage values and monitoring the same voltage values from different sources will both cause the power calculations to be inaccurate.

For example, if load A has a system voltage type of 120/208 VAC, and load B has a system voltage type of 277/480 VAC, an Energy Meter cannot be used to measure both loads in a parallel configuration. Likewise, if Load A and Load B both have a system voltage type of 120/208 VAC, but are supplied their respective voltage from different transformers, an Energy Meter cannot be used to measure both loads in a parallel configuration.

Note: When multiple sets of CTs are connected in parallel to the Energy Meter, the accuracy drops from less than 1% to between 1%-3%.


Please follow the guidelines in the attached addendum for selecting and installing the parallel CTs on an Energy meter.
Show More