Mounting Accessories Metal Bracket with Fixing Nails Horizontal

Mounting Accessories Metal Bracket with Fixing Nails Horizontal

Mounting Accessories Metal Bracket with Fixing Nails Horizontal

Item Number: 155N

Retail
$4.06
RRP (Inc. GST)

Datasheet

Barcode

Qty UoM EAN Colour
-
-
-

Specifications

Design

Product brand

Clipsal

Product or component type

bracket

Physical

Fixing center

84 mm

Depth

37 mm

Length

135 mm

Width

72 mm

EU RoHS Directive

Pro-active compliance (Product out of EU RoHS legal scope)

Toxic heavy metal free

Yes

Mercury free

Yes

RoHS exemption information

Yes

China RoHS Regulation

 Pro-active China RoHS declaration (out of China RoHS legal scope)

Material

Material

metal

Others

Accessory / separate part category

mounting accessory

Shape

rectangular

Package 1 Weight

55 g

Package 1 Height

35 mm

Package 1 width

72 mm

Package 1 Length

140 mm
Show all specifications

Frequently Asked Questions

hide show

What is part number for Optiline 70 skirting duct 155x 55?

The part number for Optiline 70 skirting duct 155x 55 is a - ISM11450

For more information on this part please refer to https://www.clipsal.com/Trade/Products/ProductDetail?catno=ISM11450


User-added image

Read a LXM32 drive ramp (ACC, DEC) using SoMachine

Issue:
How to read a LXM32 drive ramp (ACC, DEC) using SoMachine?

Product Line:
Lexium 32

Resolution:
To read the drive ramp values (ACC, DEC), you can use the function block "MC_ReadParameter".
This function block requires the modbus address of the parameter in the input "Address".
ParameterNumber must be set to 1000 (Default value).
1556 = RAMP_v_acc
1558 = RAMP_v_dec

Using GetAttributeSingle would also work. In this case, the CIP address should be used (can be found in the LXM32M manual).
CIP 106.1.10 = RAMP_v_acc
CIP 106.1.11 = 1558 = RAMP_v_dec

When is a neutral CT required?

Issue:
When is a neutral CT required?

Product Line:

Environment:

Cause:


Resolution:
A neutral CT is only required when there are loads that produce neutral current.
A neutral CT is required when an electronic-trip circuit breaker has a ground-fault option (alarm or trip) and is used on a 4 wire system. Neutral current must be factored in with phase current for accurate sensing.
A neutral CT is also required for the GFM modules when used on a 4-wire system.


CTA-ID : 1559

What is the largest trunking we do in NZ

 The larges is Actassi 155 x 55 part code ISM11400


What is the part number for a PDL DOL Starter 240V 5.5Kw

PDL56DOL12LOBGY - less overload
available on page 155 Pocket book PDL 2014

Installation Issues with Symmetra LX & 100A Supply

"

Symmetra LX is a redundant on-line double conversion UPS. Each Symmetra Power Module is rated at 4 KVA so when the Symmetra LX is fully populated with 5 power modules, it can draw up to16 KVA from the utility as one power module is redundant. This unit can be used either as a single phase or as a 3 phase unit, without any adjustments or changes being made to system to achieve this.

The Symmetra LX will operate at a voltage of 155 V to 276V , therefore it should draw a current of about 100A at 155V on a full load of 16KVA. Most European regulations require a 35 sq. mm cable for a 100A load but the Symmetra LX connectors will only take a maximum of 25 sq. mm.

However if we look at the power supply in most European countries, the voltage range is 230V - 240V and a voltage of under 200V would be very unusual. Taking a voltage of 240V and running the unit on full load the current would be just over the 65A, with 230V it would still be under 70A and we can drop the down to 200V before reaching 80A. The Symmetra LX should be protected by a slow blow Fuse / MCB which would need a sustained overload of over 1.2 times the rated current for about 2 hours to trip the Fuse / MCB, so even if the voltage drops below 200V the extra current shouldn't cause any problem.

In an area where a reasonably stable voltage exists there is no problem in using 25 sq. mm with an 80A fuse / MCB. Even with substantial voltage drops there is no danger of cables overheating or fuses blowing. In cases where the cable runs are very long and the regulations specify 35 sq. mm cable, the 35 sq. mm cable can be brought to the isolator adjacent to the unit and a 25 sq. mm cable can be used between isolator switch and UPS.

"
Show More