Dimensions for part number 157/1 is a 94mm x 54mm x 39mm.
Yes the 154/1 does plasterboard/gyprock thickness's between 19-25mm.
Yes the part number for the longer screws is a 355A. They are 50mm long apposed to the 355 which is 32mm long. Both screws are M3.5 X 0.8 Pitch.
The part number for the wall clip suitable for large format Prestige P2000 plaes is 154/2.
The 154/2 is the clip to suit any Prestige large format plate 115mm x 115mm
408/3 has 84mm mounting centres so can be mounted on standard clipsal flush box like the 157/1 for example.
Yes, we do have a wall box spacer for the 157/1PRM wall box. The part number is SL2000WBS.
The 157/1 can be used, but ensure that the wall box is mounted 25mm from outer wall surface.
Yes it will fit into 2025XA / C2025XA, with the following mounting hardware only: 154, 154RM, 154/1, 155NAR, 155VNAR, 155PRM, 156/2, 157, 164, 449A. Will not fit SC2025XA / 25XA. ( Also please note that it will need to be placed into plate in vertical configuration)
For more information on the 30USBCM please visit the Clipsal web site or click link provided .https://www.clipsal.com/Trade/search-results?q=30usbcm
Need to know what are the changes from XB2 to XB4
The XB4 requires only 1 screw to tighten on the mounting collar verses 2 on the XB2. This allows easier installation. The XB4 push buttons can accept 3 contact blocks side-by-side-by-side for a total of nine contacts on non-illuminated devices. Using the XB4 Protected LED light modules and contacts on each side will allow shallower depth than the XB2 on illuminated devices.
No, The 154 is designed to suit up to 12mm and then the 154/1 suits from 19-25mm . If These are not suitable then 155 series may be used
The wall box part number is 164/4
That bracket will suit the slimline, Saturn, ZEN and OneTouch series plates.
The part number for the wall box is 164/2
Which trip unit and BCM date code are configured for a 2 wire modbus system?
Proxima (Powerpact P, R, Masterpact)
Micrologic P and H firmware needs to be 2010-AK or later in order to set the BCM ULP to 2w+ULP mode.
Also, the BCM ULP needs to have the gray connector which will have a firmware higher than 3.x.x.
On a BCM configured for 4w Modbus, if jumpers are placed between E3 and E5, and between E4 and E6, and the mode is set to 4w on the trip unit, it will work as 2w without ULP.
Breakers shipped November 2015 and after have BCM's configured for 2w + ULP. Date code approx. 15441 and later.
replaces the F157/1 it can be used in both gyprock and masonary.
Some of the key features are:
- 1 gang
- Sliding nut
- Adjustable 84 mm centres. Robust construction
- High quality corrosion resistant finish
- Ample knockouts
- 1 and 2 hour fire rating - back to back
- Acoustic rated up to STC50
- Suitable for virtually any fire rated application
- Sound transmission rating for virtually any application
- For masonry walls
For further information please visit https://www.clipsal.com/Trade/Products/ProductDetail?catno=157/1F
The 157/1F can be used however the box will need to be recessed atleast 8mm and sealed with Fire seal.
The dimensions on the 157/1F wall box are 52mm(L) X 95mm(W) X 50mm(D).
Dimension of 157/1F is 52mm (L) 95mm(W) 50mm(D) . Mounting centre is 84mm apart .
The part number is PDL140F
The part number for the wall box is 164/3
The part number for the wall box 164/5
The 164/4 which is the wall box to suit part number B8/30/4.
dimensions 188mm x 97mm x 58 mm
What is the continuous current rating of a CA2K relay?
CTA-ID : 15484
Part number 157/1F-GASKET is not a standard part can be supplied as a special.
The dimension for a 157/1F fire rated wallbox are:
There is no plastic box the same size as 164/3, you can use PDL144Mt side by side would do the same
A9C20833 is the new code for this contactor
Dimensions of wall box 324mm x 97mm x 58mm Part no 164/7
Yes it houses 2 standard size plates, one either side.
The c clip that suits the P2033/2 switch is the 154/2.
Part number 156/2 can be used on all Prestige large format plates.
Standard 2 gang flush box will suit - part number 157/2