TMX-5E
Cavity fixing  L10190
TMX, Cavity fixing
TMX-5E
Cavity fixing  L10190
TMX, Cavity fixing

TMX Hollow WAll Anchor 5E 10x3-16 Box 100 Pcs

Catalogue Number: 1260108
TMX-5E
Cavity fixing  L10190
TMX, Cavity fixing
TMX-5E
Cavity fixing  L10190
TMX, Cavity fixing
Colour:
Colour: Per UOM Std.
  • 1 PCE

Specifications

hide show
Range of product
Thorsman
Product or component type
cavity fixing
Device short name
TMX
Provided equipment
threaded screw
Mounting support
high load installation in board material - thickness: 6-13 mm
Device application
3-16 mm high load installation in board material
Mounting support
wall mounted
Thread type
M5
Screw diameter
5 mm
Screw length
57 mm
Shape of screw head
  • combi-head
  • cross slotted
    • Screwdriver shape
      Philips
      Drilling diameter
      10 mm
      Colour tint
    • metal
    • grey
      • Quantity per set
        set of 50
        Net weight
        0.0158 kg
        Material
      • screw: steel electroplated
      • cavity fixing: sheet metal electroplated
        • Practical load capacity
        • shear: 400 N 2.5 )
        • pull-out load: 160 N 3 )
          • Thickness
            0-24 mm fixture
            Environmental characteristic
            fire resistance
            Ambient air temperature for operation
            -40-80 °C
            Diameter
            16 mm
            Length
            62 mm
            Sustainable offer status
            Green Premium product
            REACh Regulation
            Free of Substances of Very High Concern above the threshold
            REACh free of SVHC
            Yes
            EU RoHS Directive
            Pro-active compliance (Product out of EU RoHS legal scope)
            Toxic heavy metal free
            Yes
            Mercury free
            Yes
            RoHS exemption information
            Yes
            China RoHS Regulation
             Pro-active China RoHS declaration (out of China RoHS legal scope)
            Environmental Disclosure
            ENVPEP101028EN
            Circularity Profile
            N/A
            Warranty
            18 months

            Documents & downloads

            hide show
            Filter items
            • All

            • Product Brochures

            • Technical Data Catalogues

            • Catalog Page

            • Product Environmental

            • Handout

            • Declaration of Conformity

            • Certificates (MSDS)

            Frequently Asked Questions

            hide show

            Does the M580 PAC have a Hot Standby offer?

            Yes, the Modicon M580 family offers a Hot Standby offer.
            Attached is the M580 Hot Standby Planning guide

            Product Page:
            https://www.schneider-electric.com/en/product-range-selector/62098-modicon-m580---epac-controller/?filter=business-1-industrial-automation---control&parent-category-id=3900

            What is the dimension of 1260025 TMX-4E hollow wall anchor cavity fixing with screw?

            The dimension of 1260025 TMX-4E is 14mm (diameter) x 47mm (length). 1260025 is cavity fixing including fully threaded screw with combi-head and Phillips cross-slot.
            Benefits
            • Captive fixing – stays fixed even when the screw is not tightened
            • Anti-rotation design
            • Pre-assembled screw
            • High load values
            • Fire-resistant
            • Ideal for overhead cavity fixing
            Material and Operative Data:
            Material cavity fixing Expanding part: electroplated sheet metal
            Screw: electroplated steel
            Material mounting tool: Steel and plastic
            Temperature range:  –40°C to 80°C
            For further information please visit https://www.clipsal.com/Trade/Products/ProductDetail?catno=1260025
            User-added image

            What is the part Number for the Clipsal Flush mounted smoke detector ?

            The part number is 755PFM for photoelectric type and 755FM for Ionisation

            Please find attached pdf on these alarms

            For further information please visit the Clipsal Web site on the link provided.
            https://www.clipsal.com/Trade/search-results?q=755p

            If a NetShelter CX is scratched or dented can it be repaired? What color is the finish?

            Issue:
            A customer may want to touch up or repair damage to a NetShelter CX cabinet. 

            Product Line:
            NetShelter CX

            Environment: 
            All versions and serial ranges.

            Cause: 
            A NetShelter CX cabinet has been scratched or damaged. 

            Resolution:
            There are a couple of options a customer can use to disguise damage, but at closer inspection any repair work will remain visible. In most cases the repair will be visible. 
            A color marker can help cover a scratch. To fill a hole or indentation it may be necessary to first fill it, then paint it. 
            These are the colors that will patch: 
            RAL - 7016
            NCS - S8000-N
            Pantone - 433U

            How to gear in two LXM28 drives in SoMachine?

            Issue:
            Setup function block GearIn_LXM28 so that the master and slave drives follow each other perfectly

            Product Line:
            LXM28

            Resolution:
            The NUM of the GearIn_LXM28 function block should be set to 1280000 and the DENUM should be set to 8192 (2048 x 4).
            This will make the perfect gear between the master and slave.

            What is the native resolution of the encoder counts for Lexium 28 servo drives?

            The native resolution for Lexium 28 is 1280000 counts per revolution on the motor.

            This is important to know especially when using the LXM28 in gear mode.
            The factory default ratio for gear mode is 128/10      (128 = numerator  10 = denominator)
            The equates to 128 motor increments for 10 pulses applied to the pulse train input.  


            Rev 10-23-18
             

            What is the factory default scaling on Lexium 28 servo drives?

            The factory default for position scaling is 128 as the numerator and 10 and the denominator.  Parameters P1-44 and P1-45 respectively.
            These values are based on the encoder feedback resolution of 1280000 counts per revolution from the motor.

            With the factory default scaling a commanded move of 100000 will result in the motor shaft making one full revolution.


            rev 7-19-18

             

            What is the native resolution of the encoder counts for Lexium 28 servo drives?

            The native resolution for Lexium 28 is 1280000 counts per revolution on the motor.

            This is important to know especially when using the LXM28 in gear mode.
            The factory default ratio for gear mode is 128/10      (128 = numerator  10 = denominator)
            The equates to 128 motor increments for 10 pulses applied to the pulse train input.  


            rev 10-19-17

            We have some problems with ATV31 and LA9P307. Normally it works well but not in this case: LA9P307 with HUB LU9GC3 and 8 ATV31. RC-Termination is like...

            Goals and Symptoms

            We have some problems with ATV31 and LA9P307. Normally it works well but not in this case: LA9P307 with HUB LU9GC3 and 8 ATV31. RC-Termination is like manual. It works well but when one ATV31 is shut off or disconnect from Modbus the other 7 atv31 are tripping with SLF!

            When it will be switched off it gives for a short time 208 in the ETA

            Facts and Changes

            ATV31 Modbus LA9P307

            Causes and Fixes

            What is the adjusting value of PPO failure ? The problem was solved with Modbus max N adjusted to 2 in place of 7. The signification of 16#0208 in ETA is serial link fault. It was siemens PLC.


            Legacy KB System (APS) Data: RESL162527 V1.0, Originally authored by on , Last Edited by on
            Related ranges: Altivar 31

            Can the PowerLogic Energy Meter be used to monitor multiple loads?

            Issue
            A user would like to totalize multiple loads with an Energy meter.

            Product Line
            Powerlogic Energy Meter

            Environment
            Energy Meter Installation

            Cause
            The installation guide for the Energy meter does not contain instructions on wiring the meter to monitor multiple loads.

            Resolution
            *Warning: Installation and maintenance of this device should only be performed by qualified, competent personnel that have appropriate training and experience with high voltage and current devices. Failure to follow the instructions / warnings in the Meter Installation Guide can result in permanent damage to the meter, severe injury or death. 

            The Energy meter is calibrated with the set of CTs that are included with the meter, however the Energy Meter can be installed with up to three sets of parallel CTs to monitor multiple loads. When wiring multiple current transformers in parallel to the Energy Meter, all voltages corresponding to the individual loads must be the same voltage values and must be from the same source. The voltage applied to the inputs of the Energy Meter will be used in the power calculations. Monitoring different voltage values and monitoring the same voltage values from different sources will both cause the power calculations to be inaccurate.

            For example, if load A has a system voltage type of 120/208 VAC, and load B has a system voltage type of 277/480 VAC, an Energy Meter cannot be used to measure both loads in a parallel configuration. Likewise, if Load A and Load B both have a system voltage type of 120/208 VAC, but are supplied their respective voltage from different transformers, an Energy Meter cannot be used to measure both loads in a parallel configuration.

            Note: When multiple sets of CTs are connected in parallel to the Energy Meter, the accuracy drops from less than 1% to between 1%-3%.


            Please follow the guidelines in the attached addendum for selecting and installing the parallel CTs on an Energy meter.

            Can you hardwire the input/output of the Matrix-UPS?

            Issue:
            Can the input or output of a Matrix UPS be hardwired?

            Product Line:
            Matrix UPS

            Environment:
            All serial ranges

            Cause:
            A user may wish to hardwire the input/output of the UPS rather than use the supplied input power cord.

            Resolution:
            APC offers a hardwire kit to be used with the 120/208 Matrix-UPS product. The part #s for these kits are as follows:

            MXA001: 5kVA Hardwire kit
            MXA002: 3kVA Hardwire kit

            These hardwire kits replace the standard back plate and allows the input and output of the Matrix to be wired directly to their corresponding electrical panels. This kit provides 120V, 208V and 240V on the output. The electrical specifications for both the Matrix 3kVA and Matrix 5kVA UPS systems are as follows:

            Input Over-current Protection
            3kVA: 20 A
            5kVA: 30 A

            Input/Output Wire Size
            3kVA: 12 AWG
            5kVA: 10 AWG


            Description of P1-46 on LXM28 drive

            Issue:
            Description of P1-46 on LXM28 drive

            Product Line:
            LXM28

            Resolution:
            That parameter is for ESIM output resolution.
            Default is 2048 counts from the encoder output based on 1 rotation of the motors encoder at 1280000 counts

            How do I hardwire 10kva and 20kva transformers in a 208/120 or 240/120 environment

            Issue:
            Implementing a hardwire stepdown transformer in a 208v or 240v environment


            Product Line:

            Smart-UPS / Symmetra

            Environment:

            APTF10KT01, APTF10KW01, and APTF20KW01, All Serial Numbers

            Cause:

            Unbalanced UPS outputs require a stepdown transformer to power 120v loads


            Resolution:

            This document refers to installing  the APTF10KT01, APTF10KW01, and APTF20KW01 transformers in a North American 120/240 or 120/208 environment. For installations in other regions please consult the users manual.

            The wiring block outputs are as follows:


            For domestic use, make sure that the Terminal Block Jumper is installed between the Ground Terminal and Terminal 8 on the output wiring block, as illustrated on page 8 of the user manual. Please also make sure that the input voltage switch is in the correct position.

            The step-down transformer provides 240/120 output as 2 120v hots, a neutral, and a ground. It provides 208v output as a 120v hot, an 88v hot, and a ground. The 120v hot (terminal  7) and the 88v hot (terminal 9) are 180 degrees out of phase. You will measure 208v from terminals 7 to 9. The step-down transformer is not able to provide 2 120v hots that are 120 degrees out of phase as you would see with utility power.



             Note: If your installation requires both 208v and 120v output power you will need 2 separate subpanels: a 240v/120v panel and a dedicated 208v subpanel.