Quantcast

Driva TPD Plastermates Nylon Box 100 Pcs

Driva TPD Plastermates Nylon Box 100 Pcs

Driva TPD Plastermates Nylon Box 100 Pcs

Item Number: 1220010

Retail
$0.58
RRP (Inc. GST)

Datasheet

Barcode

Qty UoM EAN Colour
-
-
-

Specifications

Design

Range of product

Thorsman

Product or component type

cavity fixing

Device application

9-9 mm lightweight installation in plasterboard

Colour tint

white

Sustainable offer status

Green Premium product

Warranty

18 months

Physical

Provided equipment

without screw

Quantity per set

set of 100

Mounting support

wall mounted

Length

37 mm

Net weight

0.177 kg

Ambient air temperature for operation

-40-80 °C

REACh Regulation

Free of Substances of Very High Concern above the threshold

REACh free of SVHC

Yes

EU RoHS Directive

Pro-active compliance (Product out of EU RoHS legal scope)

Toxic heavy metal free

Yes

Mercury free

Yes

RoHS exemption information

Yes

China RoHS Regulation

 Pro-active China RoHS declaration (out of China RoHS legal scope)

Environmental Disclosure

ENVPEP111114EN

Material

Material

  • PA (polyamide)
  • glass fibre reinforced
    • Others

      Device short name

      TPD-VS

      Practical load capacity

    • 0.19 kN shear 13 mm board
    • 0.5 kN pull-out load 13 mm board
      • Thickness

        0-12 mm fixture

        Diameter

        13 mm

        Package 1 Weight

        2 g

        Package 1 Height

        13 mm

        Package 1 width

        13 mm

        Package 1 Length

        37 mm
        Show all specifications

        Frequently Asked Questions

        hide show

        What is the part number of the surface mounting box that has a duct entry?

        The part number of the surface mounting box that can accept a duct is 900SPMB. The 900SPMB is a standard pattern Surface Mounting Box for single gang accessories. Internal depth - 33mm.
        Features: 4 - 25 x 16mm Trunking Entries, including one each end and side.
        Supplied with 3 - Cat. No. 900MBC Clip-in/ push out caps, 4 - Cat. No. 220/10 Insulating Caps and 2 - M3.5 x 0.8 x 16mm long pan head screws. Screws thread into brass inserts.
        For further information, please visit https://www.clipsal.com/Trade/Products/ProductDetail?catno=900SPMB

         

        Generator does not charge my batteries using the XW or SW models?

        Generator is not charging the batteries

        If the inverter/charger qualifies the signal but the unit goes right away to passthrough, please check the following
        Make sure Charger is enabled
        Confirm that the Charger Block Start/Stop is not enabled during the times that you want it to charge

        NOTE:Ex.  If the Charger Block Start is set at 4:00am and the Charger Block Stop is set at 11:00pm, that means that it will not charge between 4am and 11:00pm.
        It would only charge from 11:00pm to 4:00am
        Tip:If there is no need to block the charging then set the start/stop times to 12:00am to disable the feature

        What is the difference between a Transformer's "temperature rise" and its "insulation class"?

        Issue:
        Explanation of the difference between temperature rise and insulation class specifications.

        Product Line:
        LV Transformers

        Environment:
        Applies to Low Voltage Transformers by SquareD/Schneider Electric

        Cause:
        Transformer Temperature Rise and Insulation Class are two different technical attributes

        Resolution:

        This question has come up because NEC 450-21(b) requires Transformers larger than 112.5 kVA to be installed in fire resistant construction unless the insulation class is 155 or higher.

        The insulation system of a Transformer is rated in degrees Celsius at its maximum temperature rating (the Class number = the degree C of the insulation system; example, a Class 220 insulation system is rated for 220°C) Transformers have either a Class 220 (former designation "H") Class 180 (former designation "F",) Class 150 (former designation "B") or Class 105 (former designation "A") Some smaller manufacturers may also use a Class 200 (former designation "R").

        The temperature rise of a Transformer is the average temperature rise that will occur in the coils during normal full load.

        The insulation system <> standard temperature rise relationships are:
        Class 220 <> 150 degree Celsius rise
        Class 180 <> 115 degree Celsius rise
        Class 150 <> 80 degree Celsius rise
        Class 105 <> 50 degree Celsius rise

        A Transformer with a Class 220 insulation system can be designed for a maximum temperature rise that is lower than the standard 150 degree Celsius. It can be designed for either 115 or 80 degree Celsius rise. As well, a Class 180 insulation system Transformer can be designed with 80 degree Celsius rise. Class 150 and 105 transformers are not typically designed for other than their standard temperature rise.

        Since all Square D low voltage dry type Transformers larger than 112.5kVA are built with a 220 degree Celsius insulation system, exception #2 under NEC 450-21(b) applies.