Discover our Clipsal Smart Home packages as seen on the Block

in location

OR

I'm looking for

  • Wholesalers
    • Uncheck All Check All
  • EXPERTISE
    • Expand
    • Expand
    • Expand
    • Uncheck All Check All
  • Switchboard Manufacturers
    • Uncheck All Check All
OR

The best way to see what Clipsal electric products can do for your home is seeing them in action at a Clipsal Display Centre.

Product stock may vary according to location. If you're after a specific product range, please check with your chosen location before visiting.

10 Results
    Load More Load Complete
    Change Location

    How to enter Pump Curve Data on an Altivar 6xx Process Drive?

    Issue:
    How to enter Pump Curve Data on an Altivar 6xx Process Drive?

    Product Line:
    ATV6xx

    Environment:
    All models and serial numbers

    Cause:
    To monitor behavior of pump curve

    Resolution:
    ATV630 Process Drive Pump Curve Setup
     
    Prerequisites to entering Pump Curve Data 
    Initial Configuration
    • Motor Settings
    • Speed Control Settings
    Pump Curves
    • Enter pump characteristics & activate pump curves

    Initial Configuration

     
    Complete Settings => Motor Parameters + AutoTune (Also available in Simply Start Menu)
    Base Frequency (BFR)  = 60 Hz
    Motor Power (NPR) =
    Nominal Motor Speed (NSP) =
    Nominal Motor Current (NCR) =
    Motor Thermal Current (ITH) =
    Motor Control Type (CTT) =
    Auto Tune (TUN) =
     
    Complete Settings => Macro Config
    Application Selection (APPT) = General Pump Control
     
    Complete Settings => Define System Units
    P Sensor Unit (SUPR) = ft
    Flow Rate Unit (SUFR ) = GPM
    Temperature Unit (SUTP) = F
     
    Simply Start
    Low Speed LSP =
    High Speed HSP =
    Acceleration ACC =
    Deceleration DEC =

    Pump Curves

    Pump Characteristics curves entered
    Activate Curves
     
     

    Pump Characteristics (Data Sheet)

     

     
    Point Flow
    (GPM)
    Head
    (Ft)
     
    Head
    (psi)
    Power
    (HP)
    1 0 80.9   76.8
    2 2585 59.5   71
    3 4509 49.5   70.2
    4 6737.7 27.1   61
    5 7720 16   51.8
    BEP 5560 40.1   66.8
     
    The following pump curve settings can be made through the Keypad display, SoMove configuration software or the embedded web page.
    Complete Settings => Pump Characteristics
    Pump Curve Mode (PCM) = PHQ
    Pump Speed (PCSP) = 1190
    Flow 1 (PCQ1) = 0
    Flow 2 (PCQ2) = 2585
    Flow 3 (PCQ3) = 4509
    Flow 4 (PCQ4)  = 6737.7
    Flow 5 (PCQ5) = 7720
    Flow BEP (PCBQ) = 5560
    Head 1 (PCH1) = 80.9
    Head 2 (PCH2) = 59.5
    Head 3 (PCH3) = 49.5
    Head 4 (PCH4) = 27.1
    Head 5 (PCH5) = 16
    Head BEP (PCBH) = 40.1
    Power 1 (PCP1 = 76.8
    Power 2 (PCP2) = 71
    Power 3 (PCP3) = 70.2
    Power 4 (PCP4) = 61
    Power 5 (PCP5) = 51.8
    Power BEP (PCBP) = 66.8
    Pump Curve Activate (PCA) = YES

    Didn’t find what you were looking for?

    Try Searching Again View Our Categories

    Need further assistance?

    Our Customer Care department provides total customer service solutions for our residential, industrial and commercial applications.

    Get Assistance