Discover our Clipsal Smart Home packages as seen on The Block 2018

in location


I'm looking for

  • Wholesalers
    • Uncheck All Check All
    • Expand
    • Expand
    • Expand
    • Uncheck All Check All
  • Switchboard Manufacturers
    • Uncheck All Check All

The best way to see what Clipsal electric products can do for your home is seeing them in action at a Clipsal Display Centre.

Product stock may vary according to location. If you're after a specific product range, please check with your chosen location before visiting.

10 Results
    Load More Load Complete
    Change Location

    Video: How do I perform basic programming on an ATV212?

    Programming Altivar 212 Drive for First Time Operation

    Product line:
    ATV212 or S-Flex 

    All models, all serial numbers 

    Basic Programming for the ATV212 drive.    


    First set TYP to 2 for 60 hz motors  (doing this first will pre-set many of the other parameters).

    Program the following drive parameters:
        0 = Terminals (most common)
        1 = HMI (keypad Run/Stop buttons)
        2 = Communications (Serial Communication)
    FNOD - Frequency reference
        1 - Ref Source VIA (4-20mA or 0-10VDC)
        2 - Ref Source VIB (0-10VDC)
        3 - HMI reference (keypad)
        4 - Serial Com Ref
        5 - +/- Speed
    AU1 - Auto Ramp Adapt (default is 1, ALWAYS change to 0 unless you understand what it does)
    ACC - Acceleration in seconds
    DEC - Deceleration in seconds
    FH - Max Frequency
    UL - Upper Limit Frequency (High Speed)
    LL - Lower limit Frequency (Low Speed)
    uL - Rated motor frequency
    uLu - Rated motor Voltage
    tHr - Motor thermal protection ( Full load amps of the motor, for overload protection)
    F111 - Terminal F logic input assignment (Programmable input, default = 2; run forward)
    F112 - Terminal R logic input assignment (Programmable input, default = 6; preset speed)
    F113 - Terminal RES logic input assignment (Programmable input, default = 10; fault reset)
    F415 - Rated motor current (Full Load amps of the motor)
    F417 - Rated motor speed (Motor rpms)
    F601 - Current Limit ( Full load amps of the motor multiplied by the service factor of the motor)
    F201 thru F204 scaling the analog input for VIA (sets scale of analog input VIA)
    F210 thru F213 scaling the analog input for VIB  (sets scale of analog input VIB)
    F201=VIA speed ref level 1 (%)                  If using 4-20mA, set to 20%. If using 0-10V, set to 0%
    F202=VIA output frequency level 1 (Hz)     For 4-20mA set to 0, For 0-10V set to 0
    F203= VIA speed ref level 2 (%)                Set to 100% unless you're using less than 10V or 20mA
    F204= VIA output frequency level 2 (Hz)   Set according to max speed (60Hz in the US)

    F210=VIB speed ref level 1 (%)                  For 0-10V set this to 0%
    F211=VIB output frequency level 1 (Hz)     For 0-10V set this to 0
    F212= VIB speed ref level 2 (%)                 For 0-10V set this to100%. If using 0-5V, set this to 50%
    F213= VIB output frequency level 2 (Hz)    Set according to max speed (60Hz in the US)

    There are many other settings and functions available.  
    Note that S-Flex enclosed drives may have different default values than listed here since the programming is often modified to match the wiring in the enclosure.

    Refer to the ATV212 Programming manual S1A53838 for further details.


    Didn’t find what you were looking for?

    Try Searching Again View Our Categories

    Need further assistance?

    Our Customer Care department provides total customer service solutions for our residential, industrial and commercial applications.

    Get Assistance