Discover our Clipsal Smart Home packages as seen on the Block

in location

OR

I'm looking for

  • Wholesalers
    • Uncheck All Check All
  • EXPERTISE
    • Expand
    • Expand
    • Expand
    • Uncheck All Check All
  • Switchboard Manufacturers
    • Uncheck All Check All
OR

The best way to see what Clipsal electric products can do for your home is seeing them in action at a Clipsal Display Centre.

Product stock may vary according to location. If you're after a specific product range, please check with your chosen location before visiting.

10 Results
    Load More Load Complete
    Change Location

    How hot can circuit breakers get? What is the temperature of a molded case breaker?

    Issue:
    What is the temperature of a molded case breaker?
    The Circuit Breaker is hot to the touch.
    The front face of a breaker feels hot.

    Product Line:
    Circuit Breakers

    Environment:
    Applies to Circuit Breakers listed to UL489 (June 2011)
    NOTE: The below information is a summary, and may contain errors.  Please see the most recent publication of the UL489 standard for complete details.

    Cause:
    A thermal graph from a testing agency that indicates the breakers are white hot.

    Resolution:
    The acceptable operating temperature of a circuit breaker is defined by UL in the UL489 standard (June 2011), which is listed below.
    • Terminations for standard rated breakers: UL 489 Paragraph 7.1.4.2.2 says the temperature rise on a wiring terminal at a point to which the insulation of a wire is brought up as in actual service shall not exceed 50°C (90°F).
    • Terminations for 100% rated breakers: UL489 Paragraph 7.1.4.3.3 says the temperature rise on the termination shall not exceed 60 deg. C (108 deg. F).
    • Handles, knobs and other user surfaces: UL489 Paragraph 7.1.4.1.6 says the maximum temperature on handles, knobs, and other surfaces subject to user contact during normal operation shall not exceed 60°C (140°F) on metallic and 85°C (185°F) on nonmetallic surfaces.

    Table 1: Summary of temperature rise and maximums for a standard rated breaker (breakers are calibrated in 40 deg. C ambient)
    Surface Temp. Rise above ambient Tem. Max at 40 deg. C ambient (104 F)
    Termination on standard rated breaker 50 deg. C (90 F) 90 deg. C (194 F)
    Termination on 100% rated breaker 60 deg. C (108 F) 100 deg. C (212 F)
    Handles, knobs, other user contact surfaces - Metallic N/A 60 deg. C (140 F) Maximum
    Handles, knobs, other user contact surfaces - Nonmetallic N/A 85 deg. C (185 F) Maximum


    The heat that is generated from inside the breaker comes from the contacts and the bimetal, which are typically the hottest parts within the breaker, and the temperature in the current path gets cooler the closer to the bus or cable, which function as heat sinks. Therefore, the sides or bottom of the breaker can be hotter than the terminations. Each breaker family or frame will have its own heating characteristics due to different designs. Smaller frames tend to run hotter on the side of the breaker than do larger frames, since the side of the breaker is much closer to the heat generators within the breaker.

    If your breaker is operating within the temperature rise and maximum values in Table 1, then the breaker should be operating normally.

    If you still believe the breaker is suspect and are concerned that the breaker may nuisance trip, then I recommend you hire Schneider Electric Field Services (Square D Services) to primary injection test the breaker to determine whether or not the breaker performs per its Characteristic Tripping Curve.

    Didn’t find what you were looking for?

    Try Searching Again View Our Categories

    Need further assistance?

    Our Customer Care department provides total customer service solutions for our residential, industrial and commercial applications.

    Get Assistance